Manuel d'utilisation / d'entretien du produit VB-43320 du fabricant Panasonic
Aller à la page of 49
Panasonic --- --- 1aIaa Digital Business System DBS Release Notes CPGEX Version 1 .O (Preliminary) Document Number: DBS-EXI O-705 Part Number: 550X07901 June lo,1996 Technical Manuals Online! - http://www.
Contents Introduction ....................................................... 5 Compatibility.. ........................................................ . 44SeriesPhoneSupport.. ............................................... . DirectoryMode .........
DBS Release Notes CPC-EX, Version 1 .O (Preliminary) Panasonic@ June lo,1996 Speed-Dial Enhancements. ......................................... 28 Additional Serial Port on CPC Card .................................. 32 Tl Networking .................
Panasonic@ JunelO, DBS Release Notes CPC-EX, Version 1 .O (Preliminary) Introduction CPC-EX Version 1.0 offers the following new enhancements to the DBS phone system: Compatibility CPC-EX Version 1.0 supports all features of CPC-B Version 7.1 (with the exception of TSAPI support).
DES Release Notes CPC-EX, Version 1 .O (Preliminary) Panasonic@ June lo,1996 New DBS features that can be executed on the 44Series phones are described below. Directory Mode On the new small-display phones, you can scroll through SSD names, PSD names, or extension names and select a displayed name for dialing.
Panasonic@ June 10,1996 DEB Release Note: CPC-EX, Version 1 .O (Preliminary; FF-Key Programming Because Tl Networking adds the capability of 4-digit extension numbering, you can now program up to 8 digits (not 6) into an IF-key. Speed Dial Enhancements CPC-EX supports up to 500 System Speed Dial (SSD) numbers.
DES Release Notes Panasonic@ CPC-EX, Version 1 .O (Preliminary) June lo,1996 ISDN Support CPC-EX supports ISDN-PRI (Integrated Services Digital Network -- Primaq Rate Interface). The program address for Trunk Circuit Type (J32 (trunk #)# 21# ) has been modified to allow for ISDN.
Panasonic@ June lo,1996 DBS Release Notes CPC-EX, Version 1 .O (Preliminary) Key Telephone Installation Desi Strip Cover Tine 44-Series Key Telephones are shipped with a thin green protective film over the Desi strip cover. Be sure to remove this film from both sides of the Desi cover before placing the phone in service.
DBS Release Notes Panasonic@ CPC-EX, Version 1 .O (Preliminary) June IO, 1996 4. Rotate the desk stand 180”. In this position it doubles as a wall mount bracket. 5. Insert the wall mount bracket into the mounting guides as shown in Figure 3. 6. Slide the wall mount bracket onto the telephone.
Panasonic@ June lo,1996 DBS Release Note! CPC-EX, Version 1 .O (Preliminary 44-Series New Phone Features Note: The new features introduced with these phones are supported by CPC-EX Version 1 .
DBS Release Notes CPC-EX, Version 1 .O (Preliminary) Panasonic@ June lo,1996 ;.’ # Feature Description 4 End Key Used to exit directory mode and return display to default mode. 5 Select Keys Used to select and dial System Speed Dial, Personal Speed Dial, and Extension numbers from a directory.
Panasonic@ June lo,1996 Figure 6. 44-Series Large-Display Phone DE3S Release Notes CPC-EX, Version 1 .O (Preliminary) Table 3. Large-Display Phone 8 dures Displays information about phone’s status, menus, dialing directories, and text message information.
DBS Release Notes CPC-EX, Version 1 .O (Preliminary) Panasonic@ June lo,1996 # Feature Description 6 MENU Key Used to return to the Main Menu screen. The default Main Menu screen contains the following items: l PERSONAL DIAL l SYSTEMDIAL l EXTENSION l FUNCTION l HELP 7 PREV Key Used to return to the previous menu.
PanasonicQ DBS Release Notes June lo,1996 CPC-EX, Version 1 .O (Preliminary) Directory Mode Description This new feature applies to the 44series small-display phone only (i.
DES Release Notes Panasonic@ CPC-EX, Version 1 .O (Preliminary) June lo,1996 l Or, to exit the directory without selecting a number to dial, press the END key or go on-hook. Notes Incompatibility with older phone versions. Directory Mode is available on the new 44-Series phones only.
Panasonic@ June lo,1996 DBS Release Notes CPC-EX, Version 1 .O (Preliminary) Notes call (FF3 ExtPort## 30#); and after dialing a busy extension (FF3 ExtPort# 33#). l Use existing addresses FFl 2# 7# l# thru 4# to assign select key features to Flexible Function Screens.
DBS Release Notes Panasonic@ CPC-EX, Version 1 .O (Preliminary) June lo,1996 Handset Mute Description While using the handset (not on speaker) during a phone conversation, you can press the MUTE key to block audio path to the other party -- you can still hear them, but they can’t hear you.
PanasoniaB DBS Release Notes June lo,1996 CPC-EX, Version 1 .O (Preliminary) Off-Hook Monitoring Description Off-Hook Monitoring lets you put a call on speaker while the handset is off-hook. You can still communicate with the outside party via the handset, but you will also be able to hear the other party on the phone’s speaker.
DBS Release Notes Panasonic@ CPC-EX, Version 1 .O (Preliminary) June lo,1996 Programming Operation to register the installation of the Analog Adapter on an extension... FF3 (ExtPort)# 51# (0 f or l)# f Extension Port where VB-44225 Lar O=Analog Adapter is not Phone is ins taf e-Display installed on this extension.
Panasonic@ June lo,1996 DBS Release Notes CPC-EX, Version 1 .O (Preliminary) Notes You can program the *71 ring select comand into an FF key. Pressing the key toggles between “Analog Port RING” and “Key Tel RING”. When the analog port is set to ring, the FF key LED lights red.
DES Release Notes Panasonic@ CPC-EX, Version 1 .O (Preliminary) June 10, 1996 SLT Onhook Flash Timer FFl 3# 14# (O-6)# AEC Disconnect FF3 (ExtPort)# 46# (0 or 1)# Analog Port on Large-Display Phone (n.
Panasonic@ DES Release Notes June lo,1996 CPC-EX, Version 1 .O (Preliminary) Notes To Confirm a Voice Mailbox Access Code Programmed into the Message Key.. Press COW MSG. The programmed access code will be displayed. Operation With Message Waiting Indicator.
DBS Release Notes CPC-EX, Version 1 .O (Preliminary) The new DSS key arrangement is shown in Figures 7 & 8. Figure 7. DSS/72 Console (VB-44320) key layout DW72 Key Layout (alphabetical) Panasonlo Panasonic@ June lo,1996 DSS/72 Key Layout (FF-key numbering) Page 24 l 44-Series New Phone Features Technical Manuals Online! - http://www.
Panasonic@ June lo,1996 Figure 8. DSSi72 #I Default Extension Numbers DSS #I Default Extension Numbers DES Release Notes CPC-EX, Version 1 .O (Preliminary) Panasonio Programming The DSS/72 console (DSS #l . . . DSS #4) is assigned to its extension number in the same manner as before: Terminal Type: FF3 (ExtPort)# 2# (11114)# where.
DBS Release Notes Panasonic@ CPC-EX, Version 1 .O (Preliminary) June lo,1996 The DSS/72 console’s FF-keys are assigned feature codes in the same manner as before (the only difference is the numberin.
Panasonic@ DBS Release Notes June lo,1996 CPC-EX, Version 1 .O (Preliminary) Figure 9. EM124 Unit (VB-44310) keys Programming The terminal type for the EM/24 is specified in the same manner as before:.
DBS Release Notes CPC-EX, Version 1 .O (Preliminary) Speed-Dial Enhancements Description Programming Panasonic@ June 10.1996 The CPC-EX supports up to 500 SSD numbers (code range 000-499) for each system, and up to 10 PSD numbers (code range 900-909) for each extension.
Panasonic3 June 10.1996 DBS Release Notes CPC-EX, Version 1 .O (Preliminary) 11. Assianina SSDs from the atjtendant phone to assign a System Speed Dial number from the attendant phone... 1. Press ON/OFF. 2. Press PROG. 3. Press AUTO. 4. Enter the SSD code (000-499).
DBS Release Notes CPC-EX, Version 1 .O (Preliminary) Panasonic@ June lo,1996 Figure 12. Assigning PSDs from programming mode to assign a Personal Speed Dial number from programming mode... FFlO 2# (ExtPort)# (900-909)# (up to 16 digits)# EXAMPLE: To chain-dial SSD code 001 and PSD codes 901-902 together into PSD code 909 on extension port 033.
Panasonic@ June lo,1996 Notes DBS Release Notes CPC-EX, Version 1 .O (Preliminary) 1) Chain-Dialing Limitations and Restrictions: l You cannot chain-dial any PSD.codes within an SSD number, because the system would not be able to choose which extension to take the PSD code from (the same PSD code might exist on multiple extensions).
DBS Release Notes Panasonic@ CPC-EX, Version 1 .O (Preliminary) June lo,1996 Additional Serial Port on CPC Card Description The CPC-EX card contains an on-board serial port (Serial Port 2) which can be used for Bus Monitor/ Remote Maintenance.
Panasonic@ June lo,1996 DBS Release Notes CPC-EX, Version 1 .O (Preliminary) Programming The following new addresses apply to CPC-EX Serial Port 2. (The addresses that control the SMDR port remain at FW 2# 2# l# thru 9#.) to program the DBS to perform Parity Check on Serial Port 2.
DBS Release Notes CPC-EX, Version 1 .O (Preliminary) Panasonic@ June 10, 1996 to specify Data Length for Serial Port 2... FFI 2# 2# 15# (3 or 4)# -f 3=7 bits 4=8 bits Notes l Serial Port 2 requires a special interface cable. l Serial Port 2 can be used for Bus Monitor/Maintenance only.
Panasonic@ June lo,1996 DBS Release Notes CPC-EX, Version 1 .O (Preliminary) Tl Networking NOTE: The following inform&on covers Tl Networking features that directly affect CPC-EX operation. For detailed information regarding TI Networking, see “Tl Networking Reference Guide”, Part No.
Dl3S Release Notes Panasonic@ CPC-EX, Version 1 .O (Preliminary) June lo,1996 Node 3 - leading digit 3 Node 4 - leading digit 4 Figure 15. Tl Network Extension Numbering.
Panasonic@ June lo,1996 DBS Release Notes CPC-EX, Version 1 .O (Preliminary) Paging Across Nefwork Nodes Every node can allow or deny network paging for each class of service. Network Route Selection A’new option is available for Forced Least Cost Routing to include network route selection.
DBS Release Notes Panasonic@ CPC-EX, Version 1 .O (Preliminary) June lo,1996 _. . Independent Node Attendant Assignment A central network operator can be assigned for Dial 0 access from any node. Each node can independantly designate a network attendant.
Panasonic@ June lo,1996 DES Release Notes CPC-EX, Version 1 .O (Preliminary) SMDR Printing Mode I: Outbound and Inbound Description SMDR data sent to Serial Port 1 can now include Network Calls also. Programming to specify the call type to be included in SMDR.
DBS Release Notes PanasoniaB CPC-EX, Version 1 .O (Preliminary) June 10.1996 Extension Numbers Description The address for extension number assignments has been modified to allow for 4-digit extensions. Programming I to assign extension numbers to ports.
Panasonic@ D6S Release Notes June lo,1996 CPC-EX, Version 1 .O (Preliminary) Other Changes to Programming Addresses Flexible Function Screen Soft-Key Assignments (FFl 2# 7# 2539# (I-lO)# (xxxxxxxx)#) and FF Key Assignments have been modified to allow up to S-digit entries.
DBS Release Notes Panasonic@ CPC-EX, Version 1 .O (Preliminary) June lo,1996 Modification to Toll Restriction Service Description The program address for TRS Operator Access (FF7 l# lS#...) has been modified to allow an extension to dial “O+NXX” phone numbers, even if “O-only” dialing is denied.
Panasonic@ DBS Release Notes June lo,1996 CPC-EX, Version 1 .O (Preliminary) IF EQUAL ACCESS CODE FORMAT IS: IF EQUAL ACCESS CODE FORMAT 1s: 0 = Old Format (10XxX ONLY) 1 = New Format (1OlXXXX ONLY) Setting Action Type of Call Setting Action Type of Call 1 Allow “O-only” and “OO-only” only calls.
DES Release Notes Panasonic@ CPC-EX, Version 1 .O (Preliminary) June lo,1996 Notes l The Operator Access address applies only to DBS systems using the new (1995) NANP dialing plan (FF7 l# 17# l#), and to TRS types 2-6 (IRS types 0 and 1 do not allow outbound dialing; TRS type 7 allows all dialing).
Panasonic@ DES Release Notes June lo,1996 CPC-EX, Version 1 .O (Preliminary) Maximum Time Priority Route Tables Description CPC-EX allows a maximum of 8 Time Priority Route Tables to be used during LCR programming. (CPC-AIL/B allows a maximum of 16 Time Priority Route Tables.
DBS Release Notes Panasonic@ CPC-EX, Version 1 .O (Preliminary) June lo,1996 . ISDN Support Description CPC-EX supports ISDN-PR.l (Integrated Services Digital Network -- Primary Rate Interface). This ISDN Interface provides 23 voice channels (“B” channels) and a control channel (“D” channel) over a 4-wire circuit.
Panasonic@ DBS Release Notes June lo,1996 CPC-EX, Version 1 .O (Preliminary) Modifications to SMDR Description Station Message Detail Recording (SMDR) provides detailed call records of outgoing calls. SMDR records can be output to a printer or an external call accounting system.
DBS Release Notes PanasonicQ CPC-EX, Version 1 .O (Preliminary) June lo,1996 Setting Modified for SMDR Values have been redefined for the SMDR Start Timer. The following table shows the new values. Note: These new values apply to CPC-EX only. Programming - to specify the SMDR Display Start Timer for CO Calls.
Panasonic@ June lo,1996 DBS Release Notes CPC-EX, Version 1 .O (Preliminary) Hardware Requirements l A printer or external call accounting system is required to receive SMDR data. Considerations l Unlike other CPC circuit cards, the CPC-EX supports two serial ports.
DES Release Notes PanasonicB CPC-EX, Version 1 .O (Preliminary) June lo,1996 Modification to Tl Signaling Types Description The default values for Tl Incoming and Outgoing Signal Types have been changed to set “Wink Start” as the default. This will allow easier programming of E&M trunks.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Panasonic VB-43320 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Panasonic VB-43320 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Panasonic VB-43320, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Panasonic VB-43320 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Panasonic VB-43320, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Panasonic VB-43320.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Panasonic VB-43320. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Panasonic VB-43320 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
