Manuel d'utilisation / d'entretien du produit V022-E3-1 du fabricant Omron
Aller à la page of 318
NT -series Programmable T erminal Operation Manual Cat. No. V022-E3-1.
.
OMRON Product References All OMRON products are capitalized in this manual. The word “Unit” is also capitaliz ed when it refers to an OMRON product, regardless of whether or not it appears in the proper name of the product.
.
T ABLE OF CONTENTS PRECAUTIONS xi ...................................... SECTION 2 Functions of the NT600S 2 ............................. SECTION 3 Hardwar e Setti ngs and Connections 23 .................. SECTION 4 System Menu Operation 65 .....
SECTION 6 Using Ho st Link/NT Lin k/C200H Direct 153 ................ SECTION 7 Using the R S-232C Interface Unit 201 ..................... SECTION 8 T roubleshoot ing and Maintena nce 241 .................... APPENDICES 255 ...................
About this Manual: This manual descr ibes the installation and operation of the NT600S Programmable T erminals ( PT s) and includes the s ections descr ibed below . Further information is prov ided in manuals on the Host Interface Units and Support T ool.
Manuals: The related manuals are indicated below . The symbol at the end of the manual number is the revision histor y symbol. Operating the Programmable terminal and Communicating with the Host NT600S Programmable T er minal Operation Manual V022-E1- (this manual) This operation manual is the manual for the NT600S its elf.
PRECAUTIONS.
1 Intended Audience This manual is intended for the following personnel, w ho must also have knowl- edge of electrical systems (an electrical engineer or the equivalent). Personnel in c harge of installing F A systems. Personnel in charge of designing F A systems.
Safety Precautions (continued) W ARNING: Do not attempt to take the NT600S apar t and do not touch any internal parts while the power is being supplied. Doing either of these may result in electri- cal shock. Switch off the power before replac ing the backlight, or you could sustain an electric shoc k.
Safety Precautions (continued) The cable’s tensile load is 30 N. Do not subject it to loads greater than this. Otherwis e a dis continuity may oc cur , caus ing operation to fail.
Safety Precautions (continued) Do not disassemble for r epairs or modification, or the produc t may malfunc - tion. The dispos al of the N T600S ( and used backlights ) may be regulated by na- tional or local author ities. Dis pose of them in ac cordanc e with the laws and regulations of the relev ant country and local authority .
.
SECTION 2 Functions of the NT600S NT600S is a new programmable terminal ( PT) which incorpor ates a host interface unit and a RS-232C interface unit in a programmable terminal body .
Section 1-1 2-1 Role and Operation of NT600S NT600S is a progr ammable terminal used to dis play and trans mit the infor mation in an F A site. The following gives a general desc ription of the role and operation of the NT600S for those who use a programmable ter minal ( PT) for the firs t time.
Section 1-1 2-1-1 Operations of NT600S Displays Screens The information to be display ed (scr een data) c an be created on a computer by using support tools and stored in the NT600S. The s creen data c an be display ed on the NT600S in response to the instructions fr om a P C/Host or touch switch op- eration.
Section 1-2 2-2 Functions of NT600S The NT600S has the following features which ar e different fr om those of exis ting NT600M; 2-2-1 Features Downsized Body The NT600S has thin depth (64 mm or less in the panel) in the NT series. The width is shorter by 50 mm, maintaining the exis ting display area.
Section 1-2 A vailability of the C200H Direct Communication Function The C200H direct communication function can be used if the C200H interface unit (NT-LB122), whic h must be purchas ed separately , is mounted to the NT600S.
Section 1-2 2-2-2 Principal Functions of NT600S Functions Related to the Data Display Character display Characters of various s izes can be dis played. Characters can flas h or be highlighted. Figure display Straight lines , cir cles, and other graphic figur es c an be displayed.
Note Section 1-2 2-2-3 Comparison between NT600S and NT600M The NT600S is a unitary PT which incorporates a system ROM, screen memory, and a hos t I/F unit (host link , NT link, and RS-232C) as the standard equipment in one body .
Section 1-2 2-2-4 Differences Between Existi ng Models and NT600S-ST121/ST21 1-EV3 Difference bet ween direct connection V er .4 and Ver .5 V er .5 of the dir ect connection func tion has the following additional functions in comparison with Ver .
Section 1-2 2-2-5 Displays The NT600S c an display various kinds of elements such as char acters, numeric value, lamps, touc h switches, and bar gr aphs on a screen. The sc reen data dis- played on the NT600S ar e created by using suppor t tools on a computer.
Reference Section 1-3 2-3 System Configuration This section gives the basic configuration of a system which uses an NT600S. Refer to the manual for individual device for information on the equipment other than the NT600S in the system.
Reference Reference Section 1-3 Host link and NT link (1:1) communications can be per formed with RS-422A by using an RS-232C/RS-422A c onverter unit (ty pe NT -AL001), but communica- tions with RS-485 are not possible.
Section 1-3 When using the C200H Direct Communication Function Use an I/O connec ting cable for the connection to the PC, and an RS-232C cable for connection to the H ost. PC made by OMRON Controls the NT600S as required for machine control, line monitoring, etc.
Reference Section 1-4 2-4 Direct Connection Function The communication method applied between the NT600S and the PC is either a host link or NT link or C200H or RS232C dir ect. The following deals with the ”direc t access” available when a host link , NT link, or C200H direct is used, and the c ommunication with a PC.
Reference Note Section 1-4 2-4-1 What is the NT Link (1:N) The NT link uses the direct connection function and c an execute high-speed com- munications with the CPU units (with built- in host link) of the CPM1, CQM1, C200HS, C200HX/HG/HE, or CVM1/CV series.
Caution Section 1-4 2-4-2 C200H Direct Communication C200H dir ect communication allows communication with C H, C200H, and C200HS CPU units by using the “direct connec tion” func tion. Advantage of C200H Direct Communication Since an I/O connec ting cable is us ed for c onnection to each CPU unit, high- speed communic ation is pos sible.
Section 1-5 2-5 Functions of the Allocated Bits and Words Elements displayed on the NT600S and the NT600S status can be allocated to the bits and words of the PC. By changing the contents of the bits and words, the NT600S can be controlled by the PC.
Section 1-5 T ouch s witches Allocation destination: Bit T ouch s witc h #12 Bit 009012 Bit 009012: ON NT600S PC The lamp c omes on ( flashes) when the PC’s control bit is ON (1) and goes of f when it is OFF ( 0). While the touch switch is pressed, the PC’ s notification bit turns ON ( 1), and when it is released, the bit turns OFF (0).
Section 1-5 Functions of the PT Status Control Area (PC to NT600S) The “PT s tatus c ontrol area” is used to control the NT600S s tatus. When data is written to this area in the PC, the NT600S reads the contents and operates accor d- ing to the contents.
Section 1-6 2-6 Communications by RS-232C Control of the NT600S by a Hos t is exec uted by two kinds of commands s upported by the RS-232C interfac e whic h is built into the NT600S. Operation commands Oper ation c ommands are used to control t he display and s tatus of the running NT600S as well as to notify information.
Note Reference Section 1-7 2-7 Before Operating Follow the procedure gi ven below to start the system of the NT600S. When using Host Link/NT Link/RS- 232C PC NT600S Support tool Check and change the PC settings. For the host link, refer to page 31 and the manuals for the host link unit and peripheral tools.
Section 1-7 Refer to the following manuals for the equipment and softwar e. Equipment or Software Manual Title Manual Number Support tools NT -series Support T ool Operation Manual V028-E1- PCs.
.
SECTION 3 Hardware Settings and Connections This section des cribes the settings of the NT600S, c onnections to a PC/Host, and other hardware settings. 3-1 Description of Par ts and Settings 24 .............................................. 3-1-1 D escription of Par ts 24 .
Caution Reference Section 2-1 3-1 Description of Parts and Settings Before getting to the operation, confirm the names and functions of parts. Also set the DIP switc hes on the NT600S. On unpac king the NT600S, c heck its external appear ance and confirm that there is no damage.
Reference Section 2-1 Rear View Lid of CFL ca se The backli ght unit and bat tery mounting holder are inst alled underneath t his lid. Contrast c ontrol (ST 121 only) Use a fine flat -blade s crewdriv er. Turn clock wise to increas e the bright ness.
Reference Caution Section 2-1 3-1-2 DIP Switch Settings Set the NT600S operation status with the DIP s witches located in the bottom right corner on the rear s ide of the body .
Caution Caution Note Section 2-2 3-2 Installation Install the NT600S to the operation panel and connect the power to the NT600S as described below. Select a proper location refer ring to Appendix D Installation Environment (page 262). Always s witch O FF the power before assembling equipment or connecting cables.
Note Reference Caution Section 2-2 3-2-2 Power Supply Connecti on Connect a 24 VDC power s upply to the power input terminals. U s e2m m 2 or thicker wires to prevent v oltage dr op. T wist the wires t ogether for wiring. Make sure you connect the power s upply wires with the correc t polarity .
Caution Note Caution Section 2-2 Fit cr imp-style terminals to the power cable. Connecting the wires of the cable to the terminal block directly after merely twisting them together c ould c ause fire and other hazards.
Reference Section 2-3 3-3 Connecting to the Support T ool Connect the NT600S to a computer with an RS-232C cable to transfer the screen data created by using a support tool to the NT600S. In other than C200H direct communications, it is imposs ible to connect a computer and the Hos t that are used to r un the suppor t tool at the same time.
Reference Section 2-4 3-4 Connection to a PC by the Host Link Connect the NT600S to an OMRON PC by the host link method. T o connect the NT600S to a PC by the host link method, the NT600S memory switch for “Comm. Method” mus t be set for the host link.
Caution Section 2-4 P C S e r i e s Units with Built-in Host Link Function CPU Units Connectable Usin g an C o n n e c t a b l e t o PC Series Host Link Unit CPU Unit C P U U n i t s C o n n e .
Note Com muni c at i ons por t 1 Com muni c at i ons por t 2 I/O p ort select or sw i t ch RS-232C ↔ RS-422A ( RS-232C/ RS-422A) ( RS-232C) Section 2-4 Connecting to a PC with a 9-pin Connector Use a connec tor cable with a 9-pin connector on both ends to c onnect the NT600S to a PC w ith a 9-pin c onnector.
Note Reference Section 2-4 Connecting to C Series CPM1 The CPM1 is connected v ia an RS-232C adapter (type CPM1-CIF01) . Procure an RS-232C 9- pin type connection cable for the connec tion. When a connector cable of 5 m or longer is required When a connector c able of 5 m or longer is required, pleas e make the cable.
Section 2-4 Connecting to a Host Link Unit T wo types of hos t link units are av ailable: a rac k-mounting type and a CPU- mounted type. The switch settings differ according to the type of hos t link unit. Set the switches ac cording to the unit type.
Section 2-4 [Setting the rear switches] CTS 0V Ext ernal I/O port selection ( selector switch ) Set this to “RS-232C”. Unit # ( DIP SW1 ) Set SW1-1 to SW1-5 to “OFF” ( “0” ) . S y nchronization ( selector switch ) Set this to “Internal”.
Section 2-4 C500/C1000H rack- mounting type: C500-LK203 [Setting the rear switches] CTS 0V Ext ernal I/O port selection (selector switch) Set this to “RS-232C”. Unit #, parity, and transfer code (DIP SW1-1 to SW1-7) Set SW1-1 to SW1-7 to “OFF” (“0”).
Section 2-4 CPU-mounted ty pe: C120-LK201-V1 [Setting the rear switches] Synchronization (DIP SW3-3 to SW3-6) Set S W3-3, SW3-5, and SW3-6 to “ON” (1), and SW3-4 to “OFF” (0). (Set thes e to “Internal”.) Unit #, parity, and transfer code (DIP SW1-1 to SW1-5) Set SW1-1 to SW1-5 to “OFF” (“0”).
Section 2-4 CVM1/CV s eries backplate mounted ty pe: CV500- LK201 [Setting the front sw itches] Set the operating c onditions with the PC System Setting functions when a CVM1/CV series host link unit is connected to the NT600S. The PC system set- tings can be made directly from the peripheral tool (LSS etc.
Reference Section 2-4 Connecting to a CPU C-series C H, CVM1/CV-series (-EV ) Only CVM1/CV ser ies CPU units designated “-EV1” or higher can be connected. Set the operating c onditions with the PC System Setting func tions when a C H, CV M1/CV-series host link unit is connected to the NT600S.
Section 2-4 [Making the PC system settings] The possibl e setting s and existi ng settin gs which c an be set by th e PC system set- ting are as given below .
Section 2-4 When using port A of C200HX/HG /HE Channel # Writing V alue Settings DM6555 0001 Host link mode Set the conditions with the contents of DM. D M 6 5 5 6 0303 Data length: 7 bits, 2 stop bits, even parity, baud rate: 9600 bps DM6556 0304 Data length: 7 bits, 2 stop bits, even parity, baud rate: 19200 bps DM6558 0000 Unit No .
Reference Section 2-5 3-5 Connection to a PC by the NT Link (1:1) Connect the NT600S to an OMRON PC by the NT link method. T o connect the NT600S to a PC by the NT link method, the NT600S memory switch for “host communication” must be set for the NT link.
Caution Note Section 2-5 3-5-2 Connecting the NT600S Refer to the illustrations below to select the appr opriate cable for the unit connec - tors and connect the NT600S to the PC.
Section 2-5 3-5-3 PC Switch Settings When the NT600S and PC are connected to eac h other , set the c onditions at the PC CPU so as to enable the NT link c ommunications.
Section 2-5 CVM1/CV-series ( -EV ) When connecting to a CVM1/CV-series (-EV ) CPU, set the switc hes as given below . I/O port selection (selector switch) Set this to “RS-232C”. NT link setting (DIP SW3) Set SW3 to “ON”. I/O p ort select or sw i t ch RS-232C RS-422A Set SW3 to “ON” (right).
Caution Section 2-6 3-6 Connection to a PC by the NT Link (1:N) Connect the NT600S to an OMRON PC by the NT link method. T o connec t the NT600S to a PC by the NT link (1:N) method, the communic ation conditions must be set with the memor y s witches.
Reference Section 2-6 Connection Diagram As shown in the figure below , c onnect multiple NT600S units to one PC. In an NT link (1:N), up to eight NT600S units can be c onnected to one PC por t. C200HX/HG/H E OMRON PC While controllin g machine ry and monitoring lines, control s the NT600S units when necessary .
Note Section 2-6 Converter Unit Connector Specifications The terminal block s pecifications of the RS-232C/RS-422A c onverter unit are indi- cated here. For details on the method for mak ing the connection c able, refer to “Making the Cable” (page 272).
Section 2-6 Wiring Method For the connections between the PC and NT600S units, wir e as shown below . The wiring method differs depending on the cables us ed for c onnection. RS-422A connection OMRON PC While controllin g machine ry and monitoring lines, control s the NT600S units when necessary .
Section 2-6 [RS-232C Cable Wiring] ( NT600S-ST121(B)- EV ) +5V (150mA) 2 3 4 5 6 9 Pin No. Abbrev. SD RD RS CS +5V SG RS-232C interface Shielding wire PT , PC NT -AL001 RS-232C interface Pin No. Abbrev. 2 3 4 5 6 9 SD RD RS CS +5V SG : Only c onnected at P C Connector cover Connector cover The pin numbers are the numbers at the NT600S.
Section 2-6 RS-485 connection C200HX/HG/H E OMRON PC While controllin g machine ry and monitoring lines, control s the NT600S units when necessary .
Section 2-6 NT -AL001 Converter Unit DIP Switch Set tings The DIP switc h settings to be made at an NT - AL001 used in the wiring depend on whether it is connected part way along the R S-422A/485 cable or is at the end of the RS-422A/485 c able.
Section 2-6 RS-422A connection, RS- 422A at the PC side C200HX/HG/H E RS-232C/RS -422A converter unit, type NT -AL001 RS-232C/RS -422A converter unit, type NT -AL001 RS-232C/RS -422A converter unit, type NT -AL001 (*) T otal cable length: 500 m RS-422A cable (*) RS-232C cable (max.
Section 2-6 3-6-3 PC Switch Settings When the PC and NT600S units have been connec ted, set the switches at the CPU module at the PC s ide in order to enable c ommunication us ing the NT link method. C series, C200HX/HG/HE W rite the communication conditions directly to the “PC system area” (data memory) us ing a peripheral tool (e.
Caution Section 2-7 3-7 Connecting to the PC with C200H Direct Communication This is the proc edure for connec ting the NT600S to an OMRO N PC by using the C200H direct c ommunication method. 3-7-1 Compatible PCs Some models and series of OMRON PCs have the direc t communic ation func tion built in.
Reference Note Section 2-7 C200H Interface Unit Part Names and Functions This section gives the names and functions of the parts of the C200H interface unit for your information before you mount the C200H interface unit to t he NT600S.
Section 2-7 Removing the unit As shown in the figure below , gr asp the unit by the cutouts at either side, then pull it out while keeping a fir m grip.
Reference Caution Caution Note Section 2-7 If unit number s 8 and 9 ar e set with a C H, a “special I/O unit error” oc curs. When an NT600S is connec ted to a C H, I/O expansion equipment c annot be connec ted.
Section 2-7 Connection to a C200H/C200HS, C200HX/HG/HE Make the connection to the C PU unit or I/O extension unit with an I/O connecting cable. The following restr ictions apply to this c onnection: Only one CPU unit, and one I/O ex tension unit, c an be connected.
Note Section 2-7 Connection to a C H Make the connection to the C PU unit with an I/O connec ting cable. The following restr ictions apply to this c onnection. Only one CPU unit can be connec ted. Up to two I/O units can be connected to one CPU unit.
Caution Reference Reference Section 2-7 Switching the power ON/OFF when using C200H direct communication The C200H inter face unit has the function of a C200H I/O extension unit. The pow- er should be switc hed ON /OFF in the way explained below.
Reference Reference Section 2-8 3-8 Host Connections by RS-232C Connect NT600S with an RS-232C Interf ace Unit ins talled to the host computer with an RS-232C cable.
Note Caution Section 2-8 Connec- i Signal name Abbrevi- i Signal direction tor pin # g ation Input Output 1 Frame ground FG --- --- 2 Send data SD (TXD) --- Ye s 3 Receive data RD (RXD) Ye s --- 4 Request to send RS (RTS) --- Ye s 5 Clear to send CS (CTS) Ye s --- 6 +5V 150mA Max.
SECTION 4 System Menu Operation This section des cribes the operation of the Sy stem Menu focusing on the procedure to start up the NT600S. Functions which will be conveni ent to use the NT600S and those which are useful for the system maintenance are also explained here.
Section 3-1 4-1 Operation Flow by the System Menu Follow the pr ocedure below when using the NT600S for the fir st time or when changing the system. Create the Screen Data Create the sc reen data to be displayed on the NT600S by using a support tool.
Note Section 3-2 4-2 Starting the NT600S When the NT600S is started, it will enter the RUN mode if system settings and screen data registration have been completed. If no screen data has been regis- tered or the screen data are destroy ed, the Sys tem Menu will be displayed.
Section 3-3 4-3 Operation Modes and the System Menu The NT600S operates in either “RUN”, “Transmit”, or “Maintenance” mode. The operation modes can be s witched by using the System Menu. 4-3-1 System Menu and the Operati on Modes Select an operation mode by press ing the cor responding touch switc h in the Sys - tem Menu.
[ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance m ode Section 3-3 4-3-2 Menu T ree The System Menu allows to ef fect various NT600S functions by using the touch switches . The NT600S’s functions with respect to the Sy stem Menu are related as shown below .
Reference Reference Section 3-3 4-3-3 Operations with the System Menu The following gives the procedur e to call the System Menu, select the menu items , and other operations with the System Menu. Make sure that DIP SW2-3 “Switch to the System Menu enabled/disabled” is set to OFF ( enabled).
[ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance M ode [ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t . Me mo r y S w i t c h e s Section 3-3 Selecting the Menu Items Press ( touch) a menu item on the scr een to select the item.
Reference Reference Section 3-4 4-4 Initializing Memory If the NT600S is us ed for the fir st time or if the scr een data is ruined and the NT600S c annot be normally st arted, the memory needs to be initialized. The memory initializ ation is required in the cases mentioned below .
[ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance M ode [ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t .
Reference [ M EM O RY I NI T I AL I ZATI ON M ENU ] Qu i t S c r e e n D a t a Me mo r y M em or y T abl es D is p la y H is to ry Me mo r y S w i t c h e s Note In itia liz e th e S c re e n D a ta M e m o ry ? C onf i r m C anc el T urn of f the DIP-Switch 2-1 and push the reset switch, then NT600S starts up normally .
Reference Reference [ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance M ode [ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t .
In itia liz e th e M e m o ry T a b le s ? C onf i r m C anc el Reference Reference [ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance M ode [ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t .
[ M EM O RY I NI T I AL I ZATI ON M ENU ] Qu i t S c r e e n D a t a Me mo r y M em or y T abl es D is p la y H is to ry Me mo r y S w i t c h e s In itia liz e th e D is p la y H is to ry ? C onf i r m C anc el Reference Section 3-4 Select “Dis play History ”.
[ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance M ode [ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t .
Reference Reference Section 3-5 4-5 Registering the Screen Data The s creen data is created by using the s upport tool and registered to the NT600S screen data memory . This sec tion des cribes the proc edure to r egister the sc reen data to the NT600S.
Caution Reference Reference Section 3-5 T ransmission in Screen Units The NT600S allows the transmis sion of data for individual s creens. The screen number of the scr een to be transmitted can be specified with the s upport tool to transmit this sc reen only to the NT600S ( it is also pos sible to trans mit multiple screens in a batch).
Reference [ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance M ode EXI T [ T RA NSMI T MODE ] S uppor t T ool M ode: N T600S EXI T [ T RA NSMI T MODE ] T ool → PT S cr een Dat a 0K B S uppor.
-- -- -- -- -- He l p Me s s a g e -- -- -- -- -- D at a successf ul y t r ansm i t t ed ( H i t any key t o cont i nue) Reference Section 3-5 7. When the sc reen data transmis sion is completed, the support tool will display the following screen.
C o mm. Me t h o d K ey Pres s Sound B uzzer Sound H os t Li nk OF F P u ttin g -O u t T im e R es um e Funct i on OF F N one ON [ M EM O RY SW I TCH MEN U ( 1 / 2) ] S uppor t T ool M ode N T600S EXI.
H os t Li nk Speed 19200bps A u to m a tic R e s e t O N [ M EM O RY SW I TCH MEN U ( 2 / 2) ] EXI T SA VE EXI T PREV . PA G E A u to m a tic R e s e t O N [ M EM O RY SW I TCH MEN U ( 2 / 2) ] EXI T SA VE EXI T PREV . PA G E PT UNI T No . 7 A u to m a tic R e s e t O N [ M EM O RY SW I TCH MEN U ( 2 / 2) ] EXI T SA VE EXI T PREV .
A u to m a tic R e s e t D at a B i t Lengt h S t op Bi t Lengt h ON 7bi t s Pa r i t y Bi t Fl ow C ont r ol 2bi t s Od d XO N/ XOFF [ M EM O RY SW I TCH MEN U ( 2 / 2) ] R S- 232C Speed 19200bps EXI T SA VE EXI T PREV .
C o mm. Me t h o d K ey Pres s Sound B uzzer Sound H os t Li nk OF F P u ttin g -O u t T im e R es um e Funct i on OF F N one ON [ M EM O RY SW I TCH MEN U ( 1 / 2) ] S uppor t T ool M ode N T600S EXI.
C o mm. Me t h o d K ey Pres s Sound B uzzer Sound H os t Li nk OF F P u ttin g -O u t T im e R es um e Funct i on OF F N one ON [ M EM O RY SW I TCH MEN U ( 1 / 2) ] S uppor t T ool M ode N T600S EXI T SA VE EXI T NEXT PA G E A u to m a tic R e s e t H os t Li nk Speed ON 19200bps [ M EM O RY SW I TCH MEN U ( 2 / 2) ] EXI T SA VE EXI T PREV .
[ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t . Me mo r y S w i t c h e s C o mm. Me t h o d K ey Pres s Sound B uzzer Sound H os t .
[ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance M ode [ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t .
A u to m a tic R e s e t D at a B i t Lengt h S t op Bi t Lengt h ON 7bi t s Pa r i t y Bi t Fl ow C ont r ol 2bi t s Od d XO N/ XOFF [ M EM O RY SW I TCH MEN U ( 2 / 2) ] R S- 232C Speed 19200bps EXI T SA VE EXI T PREV .
[ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t . Me mo r y S w i t c h e s C o mm. Me t h o d K ey Pres s Sound B uzzer Sound H os t .
Caution Note Reference Section 3-7 4-7 Starting the Operation After completing the s creen data transmiss ion, connec t the NT600S to the PC/ Host and s tart the oper ation. Carefully check the operation of all s creen data and host progr ams before using them.
[ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance M ode [ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t .
Reference Section 3-8 T o set and quit the menu, press the [SA VE EXIT] touch switch. T o quit without setting, pr ess [EXIT]. ON: The k ey press sound will be given for 0.2 s econd when a touch switch is pressed. OFF: The key press sound will not be giv en when a touch key is pr essed.
Reference [ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance M ode [ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t .
Reference [ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance M ode Section 3-8 T o set and quit the menu, press the [SA VE EXIT] touch switch. T o quit without setting, pr ess [EXIT]. When “OFF” is set, the buzzer does not s ound during operation.
[ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t . Me mo r y S w i t c h e s C o mm. Me t h o d K ey Pres s Sound B uzzer Sound H os t .
Reference [ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance M ode [ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t .
C o mm. Me t h o d K ey Pres s Sound B uzzer Sound H os t Li nk OF F P u ttin g -O u t T im e R es um e Funct i on OF F N one ON [ M EM O RY SW I TCH MEN U ( 1 / 2) ] S uppor t T ool M ode N T600S EXI.
[ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance M ode [ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t .
[ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance M ode [ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t .
[ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance M ode [ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t .
[ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance M ode [ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t .
[ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance M ode [ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t .
[ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance M ode [ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t .
[ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance M ode [ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t .
EXI T [ TOOL TRA NS MI T CHE CK ] Note [ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance M ode [ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t .
[ I / O CHE CK MENU ] Qu i t LE D B uzzer B ackl i ght T ouch S w i t ch LC D D i spl ay C om m uni cat i on I / F DI P- Swi t c h [ D I P- SW I TCH ST A TUS ] 1. For ced M em or y I ni t . O FF 2. Language Engl i sh 3. M ode C hange E nabl e 4. Reser ved 5.
[ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t . Me mo r y S w i t c h e s [ PT SET TI NG ST A TUS ] C om m uni cat i on M et hod H o.
Reference Section 3-9 4-9-4 Display History The display histor y function records the number of times that s creens for which a display history attribute has been set by the suppor t tool are displayed, and dis- plays the accumulated oc currenc e data either in order of occur rence or or der of frequency format.
[ SYST EM M ENU ] Qu i t T r ansm i t M ode M ai nt enance M ode [ MAI NT E NA NCE MENU ] Qu i t PT Se t t i n g St a t u s I/O C h e c k D is p la y H is to ry Me mo r y I n i t .
S cr een num ber No. Freq. M essage 24 ( ) Workpi ec e m i sal i gnm ent A.2 24 ( ) Workpi ec e m i sal i gnm ent A.2 4 ( ) V al ve abnor mali t y 26 ( ) Workpi ec e m i sal i gnm ent B.1 25 ( ) Workpi ec e m i sal i gnm ent A.3 35 ( ) Fr equent st op 26 ( ) Workpi ec e m i sal i gnm ent B.
SECTION 5 NT600S Functions This section des cribes the functions of the NT600S. 5-1 Creating and T ransmitting Sc reen Data 1 14 ........................................ 5-1-1 Setting the Support T ool for Use with the NT600S 1 14 .........
Reference Section 4-1 5-1 Creating and T ransmitting Screen Data This section describes briefly the support tool settings required for c reating scr een data and the screen data creation proc edure. For the details of the support tool and screen data cr eation, refer to the “NT-series Support T ool O peration Manual” (V028-E1-01).
Note Section 4-1 T o create the NT600S screen data, make settings in the “T ool Settings” screen as follows. PT T ype :NT600S Memory Size :128 KB Direct Acc ess :When using Host link /NT link /C200H direct communic ation: Ve r. 4 o r Ve r.
Section 4-1 Select “Edit Scr een”. ➡ Select a file used for stor ing the s creen data for the NT600S in the “File List” screen. T o c reate a new file, s elect “New File”. T o edit an exist ing file, selec t a file to edit. Select “New File” and pres s [Enter].
Section 4-1 PT status c ontrol area: Section 5-4 NT600S Status Control (page 192) PT st atus notify area: Sec tion 5-5 Notification of the Oper ating Status to the PC (page 197) Numeral mem.
Section 4-1 [Exiting the Edit sc reen] Return to the “Screen List”. [T o the File Selection] Enter filename to newly cr eated screen data. Return to the “File List”. Pressing the [F8] (Star t-up screen) k ey allows setting of the screen number to be displayed when the NT600S is booted.
Caution Section 4-2 It is also possible to transmit the data in sc reen units by pressing [F10] (Next) , then [F6] (Transmit) on the “Screen List” screen. Howev er , the memory table data and direct information are not tr ansferred w hen this function is used.
Section 4-2 5-2-2 Characters and Figures Which can be Displayed The NT600S s creen can display char acters , figur es, and other various elements . This section des cribes the types and attributes of the character s and figures which can be displayed and do not need to be c hanged at all.
Reference Section 4-2 Enlarged display of the char acters and marks The char acters and marks can be enlar ged to the following sc ales. x1 scale Double width scale Double height scale x4 sc.
Section 4-2 5-2-3 Communication with the Host Communication with Host Link, NT Link, and C200H Direct Communication Using the direct communication function, bits and wor ds can be allocated without restric tion to the PC memory ar ea, and data can then be direc tly written to and read from these bits and words.
Caution Section 4-2 Ascertainable NT600S Statuses The following NT600S s tatuses c an be ascertained. PT operating s tatus :Whether the NT600S is operating or stopped Screen number :Screen n.
Reference Section 4-3 5-3 Screen Display This section des cribes the sc reen information r equired for the operation with the NT600S. 5-3-1 Classification of Screens The NT600S is provided with the following types of scr eens which are classified by the display method.
Reference Reference Reference Section 4-3 Only one numer al s etting scr een which allows numeric values to be set on the NT600S s creen can be r egistered as a child sc reen. For the numeral setting, refer t o Section 4-8 Numer al Setting ( page 143).
P r oduct i on St at us Li ne A : N or m al Li ne B : N or m al 1/ 3 ➡ ➡ Reference Reference Section 4-3 Switching the Continuous Screens by Using the T ouch Switches Continuous scr eens c an be switched by using the [ ↓ ] and [ ↑ ] touch switches which have th e system key functio ns.
Reference Section 4-3 The sc reen attributes are set for eac h screen by using the “scr een selection” screen of the support tool. The support tool display s “alarm”, “backlight color” , etc.
Reference Section 4-4 5-4 Memory T ables The NT600S has the “char acter-s tring memor y table” for the charac ter data and the “numeral memory table” for numeric data which can be written and updated by the PC/Host.
Section 4-4 Enlarged display of the char acters and marks The char acters and marks can be enlar ged to the following sc ales. Double width s cale, Double height sc ale, x4 scale, x 9 s cale.
Reference Reference Section 4-4 Numerals Which can be Displayed The power of expr ession of the s creen can be i ncreas ed by giving various attrib- utes such as the enlarged or reverse display to the numerals of the numeral memory table.
Reference Reference Section 4-5 5-5 Bar Graphs The c ontents of the numeral memory tables of the NT600S c an be dis played as bar graphs as well as numeral data. Setting for bar graphs is made when creating the sc reen data using the suppor t tool.
Section 4-5 Orientation and incremental direc tion The orientation and incremental direction of the bar graph can be selec ted from those mentioned below. ↑ (up): The bar graph incr ements upward in the v ertical orientation. ↓ (down): T he bar graph inc rements downward in the vertic al orientation.
Section 4-5 [T o display a value below 0 %: Sign display “Y es”] The bar graph is displayed in the r ange of - -100 % to 100 %. The middle of the bar graph indicates 0 %. % display 0 % 100 % - -100 % -- 6 0 % [Not to display a value below 0 %: Sign display “No”] The bar graph is displayed in the r ange of 0 % to 100 %.
Section 4-5 (2) When the absolute v alue of the % value is in the range of 100 % to 999 % The % v alue is displayed as it is . Sign display “No” : The display will be as mentioned below ac cording to the graph frame s etting.
Section 4-6 5-6 Lamps The NT600S has the “lamp” func tion used to simply dis play the PC bit status. Set the lamp function when creating the s creen data using the support tool. The following describes the k inds of lamps that c an be displayed.
Section 4-6 Guide display mes sage Lamps c an be displayed with the guide display messages . ➡ The guide display message attributes are the same as that for the “c haracter display”. Refer to “ Characters and Figures whic h can be Displayed” (page 128).
Section 4-6 When a lamp is overlapped with a memory table display The guide display message for a lamp is a fixed character -string. If you want to change the lamp guide display in ac cordance with some condition, overlap t he dis- play area of a numeral memory table or character- string memory table w ith the lamp.
Caution Correct use Section 4-7 5-7 T ouch Switches The NT600S has a func tion whereby input oper ations can be performed by us ing touch panels displayed on the screen. NT600S screens can be switched, or bit information sent to the PC, by pr essing (lightly touching) the “touch switc hes” in a panel.
Reference Section 4-7 Caution on pres sing touch s witches at 3 points When multiple touch switches are created at the relative positions indicated in the example below , malfunctions may occ ur due to the character istics of this switch c onfiguration.
Section 4-7 Functions of touch s witches T ouch s witches can have the following func tions: - PC notific ation func tion Direct connection (page 181) RS-232C c ommunication ( page 205) - Sc.
Reference Section 4-7 5-7-2 Standalone Function The NT600S has a function that allows screens to be switched by pressing touch switches on its scr een, rather than by designation from the PC. This function is called the “standalone function”.
Reference Reference Section 4-7 5-7-3 System Key Functions The NT600S allows the allocation of “system key” functions to touch switches. The system key functions can then be used during operation by pressing the touch switches to which they have been allocated.
Caution Section 4-8 5-8 Numeral Setting The NT600S has a “numeral setting” function to enable numerical values to be in- put from the s creen. This function inputs numer ical values to numeral memory tables in r esponse to touch switc h operations, displays thes e numerical values on the screen, and sends them to the host.
Correct use Section 4-8 When there is no s ign display :0 to 99999999 (8 digits ) When there is a s ign display :- -9999999 to +9999999 (7 digits for negativ e numbers , 8 digits for pos iti.
Section 4-8 Numeric Key T ype When a numerical v alue is input using touch s witches to whic h numeric key func- tions hav e been allocated, the input numerical value is display ed on the screen.
Section 4-8 5-8-3 Creating Numeric Keys In order to input numer ical v alues using the numeral setting function, apart from the display area for the numeral setting, the numeric k eys mus t also be created. Setting Screen Attribute s The type of numeric k eys can be selected using the numeral s etting attributes of the screen attributes.
Reference Section 4-8 Numeric Key Allocations The following special touch switc h number s (numeric key numbers) ar e allocated to the numeric key s. T ouch Switch Number Numeric Key T ouch Switch Number Numeric Key T ouch Switch Number Numeric Key 227 (*) Menu display 237 6 247 CLR 228 238 7 248 229 239 8 249 .
Section 4-8 5-8-4 Using Numeric Keys T o input numerical data at a numeral s etting area during operation, first select the numeral setting at which the data is to be input, and then input the numerical value by pressing the numeric key s (touch s witches) .
Section 4-8 Inputting Numerical V alues Input numeric al v alues using the following numeric keys (touch switc hes): numer- als (0 to 9), dec imal point ( .
Reference Section 4-8 Upper/lower limit check (only w hen using direct connection) By s etting a maximum v alue and minimum v alue for input numeric al values , the storage of erroneous v alues outside the applicable r ange in numeral memory tables and their notification to the PC/Host can be prevented.
Section 4-8 Upper/lower limit chec k An upper/lower limit check is executed when the incrementing/decrementing ( +, - -) key s are pr essed. If the input numer ical v alue is outside the valid range, the data in the numeral memory table before the k ey was pr essed is r edisplayed and notified to the host.
.
SECTION 6 Using Host Link/NT Link/C200H Direct This s ection des cribes how the NT600S can be us ed when using the Host link /NT link/C200H direct. 6-1 Outline of Hos t Link / NT Link / C200H Direct Operation 154 .......................... 6-1-1 Equipment and Settings Us ed in This Chapter 154 .
Reference Reference Section 5-1 6-1 Outline of Host Link / NT Link / C200H Direct Operation This section des cribes the basic s for operating the NT600S through communica- tions with the PC using the Host link/NT link/C200H direc t.
Section 5-1 6-1-3 NT600S Status Control and Noti fication to PC This section des cribes the fundamentals of the dis play elements, NT600S status control, and notification which are the basic s of the NT600S functions.
Reference 000 n+3 CH 15 14 13 12 1 1 10 9 8 Bit Section 5-1 Controlling the NT600S Status by Using Allocated Bits and W ords ..... PT Status Control Area (PC to PT) The PT status control area ( PC to PT) is provided to c ontrol the NT600S s tatus from the PC.
Caution Reference Section 5-1 The PT status c ontrol area (PC to PT) can be alloc ated to the following PC areas. Symbol CS e r i e s P C s Allocated CVM1/CV S eries PCs Allocated DM Data me.
Reference Reference Section 5-1 Notifying the NT600S Status by Using Allocated Bit s and W ords ..... PT Status Notify Area (PT to PC) The PT status notify ar ea (PT to PC) is prov ided to notify the NT600S status changes to the PC.
Reference Caution Reference Section 5-1 As the number of the numeral table is wr itten, the PT status numeral setting strobe flag is simultaneous ly s et ON (1) .
Reference Reference Reference Section 5-1 6-1-4 Switching the Screen Display The following describes the proc edure used to s witch the NT600S s creen display by controlling from t he PC. The display screen c an be s witched also by pres sing a touch s witch during the operation after r egistering a scr een number to the touch switch.
Reference Reference Section 5-1 Use of the scr een switching strobe Create a progr am to read the number of the currently displayed screen and to write the number to the “s creen switch s etting word” at the leading edge of the “scr een switching strobe” of the PT status notify area.
Reference Section 5-1 6-1-5 Notifying the Display Screen to the PC (T o Display the Number of Currently Displayed Screen) The following descr ibes the processing to dis play the number of currently dis- played scr een of the NT600S. This proces sing reads the data from the PC s tatus notify area.
Reference Section 5-1 Procedure 1. Us e the support tool to allocate the PT status notify area (PT to PC) to the PC memory . 2. Create a PC program to read the “curr ently displayed sc reen wor d” in the in the PT st atus notify area when the “sc reen switch str obe flag” in the PT status notify area has tur ned ON.
Reference Section 5-2 6-2 Memory T ables and Bar Graph This section des cribes allocation of the memor y table t o PC words, and changes to the c ontents of words neces sary to display char acters, numerals, and graphs by communicating with the PC using the Host link/NT link .
Section 5-2 Direct s pecification Direct s pecification is a method of s pecification in which the c ontents of dis- played memory tables are directly corr elated with the contents of the allocated words.
Note Section 5-2 Number of registr ation words Set the number of wor ds within 20 words required for registering the character- string data. One word can stor e two half-size charac ters or one full-siz e charac- ter .
Note Section 5-2 Setting the Words of the Numeral Memory T able When creating the screen data by using the s upport tool, mak e the following set- tings for each number ed numeral: Initializ.
Note Section 5-2 Available allocation wor ds The memory tables c an be allocated to the following PC areas: CS e r i e s P C s CVM1/CV Series PCs Sym bol A r e a N a m e Allocation A r e a N.
Reference Section 5-2 Displaying the numer al memory table Numerals can be displayed in three different ways according to the contents of the numeral memory table, as mentioned below. The most significant digit ( digit 4 of a single wor d or digit 8 of a double word) is process ed in different way s.
Reference Reference Section 5-2 Contents of the character -string memory table A character- string is stored i n the allocated words beginning with the first wor d in half-size or normal- size char acters. T wo half-s ize charac ters or two normal- size char acter is stored in one wor d.
Reference Section 5-2 When it is necessary to dis play changing data such as monitored data of wor ds in the PC, us e the numeral and charac ter-str ing memory tables. This must be used to change the display contents (c ontents of memor y table and words) .
Section 5-2 PC ladder program Create a PC ladder progr am as follows : INC(38) DM0000 00100 INC(38) DM0001 (1) Word for leas t s ignifi cant 4 digits of #1 (2) Word for most signifi cant 4 d.
Reference Section 5-2 In this section, the procedure for changing the display contents by using method (1) is explained. Method (2) involves changing the contents of the allocated table.
Section 5-2 Example of Changing a Character-String in Indirect Specificat ion An example in which the character-str ings being display ed are changed by adding the contents of the wor d allocated to the numeral memor y table which is us ed in indirect specific ation is given below.
Reference Reference Section 5-2 Program operation When the program is executed by displaying the screen on the PT , the following operation is performed. (1) Each time contact 00100 comes O N, the display on the NT600S c hanges to the next item in the following sequence.
Reference Section 5-2 Available allocation wor ds The PT status control area can be allocated to the following PC areas: Symbol CS e r i e s P C s Allocated CVM1/CV S eries PCs Allocated DM .
Section 5-2 Order for w riting to the PT status control area (PC to PT) First write the “copy destination memor y table number”, and then, wr ite the “copy source memory table number” to the PT status c ontrol ar ea (PC to PT) . The NT600S reads the area sometimes when the PC is wr iting the settings.
Section 5-2 PC ladder program Create a PC ladder progr am as follows : @MOV(21) #0004 09000 @MOV(21) #0010 (1) Copy type, copy des tination m emory table # Copy destinat ion word Copy source.
Reference Reference Section 5-2 6-2-5 Upgrading Bar Gr aphs (Changing the Contents of Allocated W ords) The following describes the proc edure to upgrade the bar graph display on the NT600S by changing the contents of the alloc ated words.
Reference Reference Section 5-3 6-3 Lamps, T ouch Switches, and Numeral Setting This section descr ibes bit allocation for lamps and touch switches and the method used to find the numeral input using the numeral s etting function, when communi- cating with the PC using the Host link/NT link/C200H direc t.
Reference Section 5-3 6-3-2 T urning ON (lit) and OFF (unlit) the Lamps (Changing the Contents of Allocated Bits) The following describes the proc edure to change the lamp display status on the NT600S by changing the contents of the alloc ated bits.
Section 5-3 Lamp #5: Word 000205 (output bit to unclamp rotate robot arm), guide display message “UNCLAMP” Contents r egistered to the sc reen: Lamp #0 to #5 Line 1 Process 3 Conveyor Lo.
Section 5-3 6-3-3 Allocated Bits, and Display , of T ouch Switches Method for PC Notification and NT600S Control T wo types of bit can be allocated to touch switches : notify bits - which ser ve to notify statuses to the PC - and c ontrol bits, lamp bit, whic h control the lighting (flashing) of the touch switches.
Section 5-3 Notes on the Notification Operation The touch switch notific ation operations are as follows: T ype of Notification Operation When Using Host Link or NT Link with DM Are a When U.
Reference Section 5-3 6-3-4 Lit (Flashing) and Unlit T ouch Switch Statuses (Changing the Status of Allocated Bits) This section des cribes how to change the statuses of allocated bits and thereby the statuses of the touc h switches display ed by the NT600S.
Reference Section 5-3 The status of the notify bit reflec ts the touch s witch status , as follows : Momentary : 0 (OFF) ... Not pressed 1 (ON) ... Press ed Alternate : The bit alloc ated for notification is set to 1 (ON) if currently 0, and to 0 (OFF) if cur rently 1.
Section 5-3 Important Points T ype of Notification Operation When Using Host Link or NT Link with DM Are a When Using C200H Direct Communication or NT Link with other than DM Area Momentary .
Section 5-3 T ouch s witch #1 1: Function “Notify Bit” Display attribute “Light” Control bit CH 05001 (Stop flag) ... Guide mess age: “ STOP” Notify bit CH 06001 Data registered .
Section 5-3 Program operation The operation when the program is executed is pres ented below . Execut e program Press Run touch switc h. Press Stop touc h swit ch.
Reference Section 5-3 [“Conte nt upgrade mem ory table ” in the PT sta tus not ify are a and PT sta tus] 00 1 5 1 4 1 3 1 2 1 1 1 0 9876 5432 10 B i t -- 0 -- -- 0 0 0 Word m+1 15 14 13 .
Section 5-3 Application Example This example shows the reading of the numeral memory table number after a val- ue has been changed by inputting numer ical data at the NT600S. Setting at the s upport tool Make the following settings us ing the support tool.
15 14 13 12 1 1 10 9 8 7 6 5 4 3 2 1 0 Bit 000 Word n+3 15 14 13 12 1 1 10 9 8 Bit PT status control bits 00 PT stat us control desi gnation Section 5-4 6-4 NT600S Status Control The statuse.
Reference Section 5-4 Screen dis play (bit 15) The screen display bit is used to display and clear the scr een to prev ent “burn-in” on the CRT . Set bit 15 to 0 (OFF) to clear the screen. (When the LCD display unit is used, the backlight will also go OFF at the same time.
Reference Reference Section 5-4 Continuous buzz er (bit 13) and intermittent buz zer (bit 12) In the case of both buzzer s, when the respectiv e bit is ON the buzzer s ounds and when it is OFF the buzzer does not s ound. The “continuous buzzer ” sounds continuously without interruption.
Reference Section 5-4 6-4-2 How to Control NT600S Functions This section des cribes how to control the func tions of the NT600S. Restrictions on allocating wor ds The PT status control area (PC → PT) can be allocated to the PC memory areas listed in the following table.
Section 5-4 PC program Create the following PC ladder program. @MOV(21) #A000 103 09002 09003 09002 @MOV(21) #9000 103 @ANDW(34) 103 #CFFF (1) Displ ay t he scr een, sound cont i nuous buzze.
Caution Section 5-5 6-5 Notification of the Operating Status to the PC (Determining the NT600S Operating Status) The status ( operating statuses , etc .) of the NT600S can be determined from the PC by reading the “PT s tatus” word in the PT status notify area allocated in the PC memory .
Section 5-5 Battery (bit 13) If the voltage of the bac kup battery for the NT600S memory becomes low, this bit is set to O N (1) . - T his bit is v alid only when DIP s witch 2-8 is ON (1).
Reference Section 5-5 Since all the CVM1/CV-s eries special auxiliary relays are allocated to the system, they cannot be used for applications not related to the system. The range of each memory area differs according to the PC ty pe. See “Appendix L PC Memory Map” (page 291) for more details.
Section 5-5 Program operation (1) If PT operating status (contact 1 1215) is tur ned OFF (0) and battery (con- tact 1 1213) is turned ON (1), “ 1” ( NT600S stop, low battery voltage) is trans- mitted t o DM0001.
SECTION 7 Using the RS-232C Interface Unit This section des cribes how to use the NT600S when it is connected to a Host using the RS-232C interf ace. 7-1 RS-232C Interfac e U nit Communications 202 ....................................... 7-1-1 C ommunication Procedur e 202 .
Reference Section 6-1 7-1 RS-232C Interface Unit Communications The communication proc edure through the RS-232C cir cuit and the program flow using examples in BASIC are des cribed below. 7-1-1 Communication Procedure The Host and NT600S communic ate ac cording to the following procedur e.
Section 6-1 Operation by Operating Commands The following describes c ontrol of the NT600S using the operating commands, and the flow of notifications fr om the NT600S. For the actual procedur e for using the operating commands, r efer to 7-2 Com- mands Sent by the Hos t (page 208) and 7- 3 Commands Sent by the NT600S (page 218).
Reference Section 6-1 7-1-2 Precautions Some impor tant points to c onsider when us ing commands are lis ted below . Command Length If a mistake during command specification r esults in a command being too long, the correc t length of the command is ex ecuted and the remainder is ignored.
Note Section 6-1 7-1-3 Notification and Contr ol of T ouch Switches If a touch switc h is pr essed, the corr esponding touc h switch number or bit informa- tion is sent to the Host. Conversely , t o turn ON a touch switch or cause it to flash, the touch switch number or bit information is sent from the H ost.
Section 6-1 7-1-4 T able of Commands Operating Commands Ty p e Command Name Page Screen control [ESC] 0 Display Specified Screen 208 [ESC] X Request Screen Number 209 Memory table op- e r a .
Ty p e Command Name Page Delete [ESC] & Clear Screen 222 Character Size [ESC] ) Character Specify Size 222 [ESC] Specify Character Enlargement 223 Character Display A t t r i b u t e s [.
Note Reference Section 6-2 7-2 Commands Sent by the Host The operating commands s ent by the Host are descr ibed below . All data v alues must be s ent in ASCII code.
Section 6-2 Inquiry of the displayed screen A s creen number can be inquired using the f ollowing command to k now the num- ber of the displayed s creen. Request Screen Number Format 1B [ESC] 58 x Description Enquires what number sc reen is displayed on the NT600S.
Reference Section 6-2 If the actual c haracter s tring is longer than the s pecified char acter string length, the specified number of c haracters is written and the remainder ar e discarded. A timeout err or mess age is display ed if the actual character str ing is shor ter than the specified char acter s tring length.
Reference Section 6-2 Copying the Memory T able Use the following command to change numerals or character -strings to be dis- played on the NT600S after copying the contents of a memory table.
Bit Parame ter Section 6-2 7-2-3 Lamps and T ouch Switches The procedure for changing/c hecking the display status of lamps and touc h switches , and that for disabling input from the touch switches using c ommands from the Hos t are des cribed below .
Reference Section 6-2 Bit ON: The lamp or touch switc h is turned on (or caused to flash). Bit OFF: The lamp or touch switch is turned off. Example T o turn on lamps and touc h s witches wit.
Reference Reference Section 6-2 Description Enquires the s tatus of a lamp or touch switch s pecified by its addres s. The NT600S returns the Lamp and T ouch Switch Display Status Res ponse Com- mand ( refer to 7-3 Lamp and T ouch Switch Display Status Response ) to repor t the display status .
Reference Reference Section 6-2 7-2-4 Controlling the NT600S Status The NT600S status can be controlled by the Host. T urning OFF the Backlight / Preventing Afterimage By turning off the bac.
Reference Section 6-2 Displaying t he System Menu By using the following command, it is pos sible to enable or disable display of the NT600S system menu.
Reference Section 6-2 Controlling the LCD Screen When the LCD screen is used, the normal or invers e dis play mode c an be selected by using the following command.
Section 6-3 7-3 Commands Sent by the NT600S The operating commands s ent by the NT600S to the Host ar e described below . 7-3-1 Screen Display Notifying the Display Screen The scr een number of the screen currently display ed on the NT600S is sent to the Host on execution of the following command.
Reference Section 6-3 Description A number with 4 transferred digits set with the NT600S number s etting function is reported to the Host with this c ommand.
Bit Parame ter Section 6-3 Notifying t hat a T ouch Switch Has Been Pressed When “On” is set for “Bit In” when setting the scr een attribute with the support tool, the “touch switc h pressed” s tatus is s ent to the Host in the bit information.
Reference Section 6-3 T ouch Switch Number Output (from NT600S to Host) Format 1B [ESC] 48 H m 1 m 2 m 3 0D [CR] m 1 m 2 m 3 : Address of the pr essed touch switc h (3-digit hex adecimal) 00.
Reference Reference Section 6-4 7-4 T erminal Commands T erminal commands allow the display of information from the Host as text and graphics, independently of the s creen stored in the NT600S.
Reference Reference Section 6-4 The character str ing is specified with the Specify Dis played Charac ters Com- mand (refer to 7-4-2 Specify Displayed Char acters ).
Reference Reference Section 6-4 Specifying t he Inverse Display Use the following command to set the inver se display mode. Set Inverse Display Format 1B [ESC] 22 ” Description Sets the display attr ibute to inver se s o that all charac ters and marks sent subs e- quently ar e highlighted.
Reference Reference Reference Section 6-4 The Set Flas hing Display Command is cancelled by the End Flas hing Display Command or the Normal Display Command (refer to 7-4-2 Normal Dis play and 7-4-2 End Flashing Display ).
Reference Section 6-4 Specifying t he Character-string The char acter-s tring to be display ed can be spec ified by the following c ommand. Specify Displayed Characters Format 1B [ESC] 34 4 .
Section 6-4 Displaying t he Circle Us e the following command to display a circle. Draw Circle Format 1B [ESC] 38 8 x 1 x 2 x 3 y 1 y 2 y 3 r 1 r 2 r 3 x 1 x 2 x 3 : X coordinate of circ le .
Note Section 6-5 7-5 Key to Programs The following pr ograms include all the c ommands that can be used w ith the NT600S. 7-5-1 Use of Programs The sample program appear s as follows on the screen.
Section 6-6 7-6 EXAMPLE PROGRAM.
Section 6-6.
Section 6-6.
Section 6-6.
Section 6-6.
Section 6-6.
Section 6-6.
Section 6-6.
Section 6-6.
Section 6-6.
Section 6-6.
! " #.
Caution Section 7-1 8-1 Hardware Faults When a fault relating to the operation of the NT600S occ urs, find the symptoms in the table below and respond by following the cor responding “Remedy” indicated in the table. Confi rm system safety before t urnin g the po wer ON/OFF or resetti ng.
Section 7-1 NT600S Symptom s C ause Remedy Buzzer sounds, RUN LED is OFF . Malfunction due to external noise. Distance the communication cable from the source of the noise and insert a noise filter in the power supply line.
Section 7-2 8-2 Responding to Displayed Error M essages When the NT600S dis plays an er ror mess age, find the c orresponding s ymptoms in the appropriate table below and respond by following the “Remedy” indicated in the table.
Note Section 7-2 8-2-4 Communication Errors This section des cribes the err ors relating to communication with the PC that can occur dur ing operation, and their remedies. Operation when a communic ation err or occur s When a communica tion error occ urs, the error message is displayed at the NT600S, and the buzz er s ounds.
Section 7-2 Message Cause Remedy Parity Error Framing Error O v e r r u n E r r o r Communication param eters set incorrectly. C heck whether the parity bit, data bit length, baud rate, stop bit length, and flow control settings of the PC/Host match the settings of the NT600S.
W ARNING Section 7-3 8-3 Maintenance of the NT600S Carry out maintenance work in order to ensure that the NT600S is always used in its optimum c ondition. Do not attempt to take the NT600S apart and do not touch any internal parts while the power is being supplied.
W ARNING Section 7-3 Replacing the Backlight Switch off the power before replac ing the bac klight. O therwise y ou could sus tain an electric shoc k.
Section 7-3 3. Remove the backlight ( -s haped). Remove the backlight, lifting it upward, by pulling the left handle after pushing the right handle to the right. 4. Fit a new backlight. Hold the handle and insert the projection at the right s ide face of the unit into the hole in the NT600S.
Note Section 7-3 Replacing the Battery The NT600S uses a lithium battery to back up the memory c ontents. The battery life is 5 year s if the NT600S is used in a l ocation where the ambient temperature is 25 C. If the temper ature at the location of use i s higher than this, the battery life w ill be shor ter .
Reference Caution Note Section 7-3 3. Pull out the battery together with the connector. 4. Install a new battery . Insert the battery connector, keeping it straight. 5. Close the CFL case lid and s ecure it with the scr ew . The battery may be replaced while the power is ON.
Note Section 7-4 8-4 Inspection and Cleaning Clean and inspect the NT600S regularly to ensure that it is always used in its opti- mum condition. Cleaning Method If the dis play is dirty the sc reen is difficult to see. Clean the scr een from time to time as follows.
Caution Section 7-4 Points inspected Inspect the following points to determine if ther e is any divergence from the stated c riteria. If there is, either improve the surr ounding environment so that the values fall within the stated r ange, or adjust the NT600S.
.
Appendix A APPENDIX A Specifications General Specifications Item Specification Power supply voltage 24 VDC Allowable power supply v oltage range 20.4 VDC to 26.4 V DC (24 VD C - -15% +10%) Power consumption 24V , less than 15W (ST121 (B)-EV ) 24V , less than 25W (ST21 1 (B)-EV ) Inrush current 3Am a x .
Appendix A Performance Specifications Display Specifications Item Specification D o tm a t r i x o fS T N liquid crystal display Number of dots (resolution) 640 dots (vertically) x 400 dots (horizontally) (dot size: 0.
Appendix A Display Capacity Item Specification Displ ay l t Character displays Fixed character data (character strings registered for each screen) y elements Character string displays 256 st.
Appendix A Special Features Item Specification Buzzer T wo types: Continuous sound and intermittent sound Setting: Set “key press sound” in the “Memory Switch” menu of the Maintenance Mode ON. If “ERR ON” is set the buzzer only s ounds when an error occurs.
Appendix A Communications Specifications [For a Host Link] Item Specification Communications standard EIA RS-232C Communications settings Start-stop synchronization Baud rate: 9600, 19,200 b.
Appendix B APPENDIX B Dimensions [ Body ] NT600S-ST121(B)-V NT600S-ST211(B)-V POWER RUN 275 (10.81) 263 (10.34) 192 (7.55) 180 (7.08) 6(0.24) 71 (2.
Appendix B [ Installation ] Unit : mm (inch) 180 (7.09) 287 (1 1.3) 15.5 (0.61) 34 (1.34) (min.) 38 (1.5) (max.) Installation fitting Installation panel 204 (8.
11 0 (4.33) 53.5 (2.11) 74.5 (2.93) 100.2 (3.94) 105 (4. 13) or les s 4 (0.16) 30 (1.18) 30 (1.18) 45 (1.77) (Unit: mm) Appendix C APPENDIX C Handling the RS-232C/RS-422 Converter Uni t This section shows the dimensions of the RS-232C/RS-422 conver ter unit (NT-AL001), and descr ibes the methods for installing and removing it.
Note Appendix C Installation on a DIN Rail Hook the t op part of the rear of the converter unit ( (a) in the figure) onto the top edge of the DIN r ail, and push the unit in direction (b) . Then fit end plates on the right and left sides of the converter unit s o that the unit cannot shift s ideways.
Caution Appendix D APPENDIX D NT600S Installation Environment When installing the PT in the operation panel, obs erve the following points. See also the s ection “G etting Starting”. The view angle of the LCD s creen is 50 to the left and 40 to the right.
Note Appendix D T ake the following points into ac count in order to prevent noise (1) Avoid installing the unit in panels in whic h high-voltage equipment is als o installed. (2) Install the unit at a distance of at least 200 mm fr om power lines.
Note Appendix E APPENDIX E Method for Maki ng the Cable for Connecti on to the PC/Host Explained below is the method for making the c able that connects the NT600S and the PC/Host. Connect the wires to the connec tors in accor dance with the connector s pecification for each unit.
1 6 9 5 Correct Use 1 14 25 13 Appendix E Connector Specifications and Wiring for OMRON Units The combination of pin numbers to w hich the connecting wires are connected differs according to the connec tor specifications for each unit.
2. C500-LK201 and C200H-LK201(-V1) only.
1 6 9 5 Appendix E Wiring Connections The NT600S does not use pin 4 (RS) or pin 5 (CS) . Either s hort the RS and CS pins of the PC connector together or set the CTS setting s elector s witch at the rear face of the hos t link unit to “0V” (s ee in the figure).
1 14 25 13 1 6 9 5 Appendix E Wiring Connections The NT600S does not use pin 4 (RS) or pin 5 ( CS). Short t he RS and CS pins of the PC connector together (s ee in the figure) . Connect the cable shielding wir e to the connector cover and pin 1 at both the NT600S and CPU ends of the cable.
Appendix E Wiring Connections CVM1/CV-series host link units have two ty pes of connec tor , which mus t be wired differently . The NT600S does not use pin 4 (RS) or pin 5 (CS) .
Note 1 6 9 5 Appendix E Connecting an NT600S to a C Series C200HS, C200HX/HG/HE, or CPM1, CQM1, CVM1/CV Series ( -V )C P U Unit (Including Communication Port) C-Series C200HS, C200HX/HG /HE,.
Reference Appendix E Connecting an NT600S to an RS-232C/RS-422 Converter Unit ( NT -AL001) Connecting to an RS-232C/RS-422 conver ter unit allows transmissions over distanc es greater than 15 m (maxi- mum of 500 m).
Note Appendix E NT -AL001 RS-422A terminal block specifications Connected terminal bloc k: RS-422A terminal bloc k (M3 screws ) Electrical c haracteristic s: Confor m to EIA RS- 422A Signal direction: Signal input and output is relativ e to the NT-AL001.
Appendix E Making the Cable The proc edure to mak e up the c able is desc ribed below . Refer to the following explanation when making an RS-422A c able also. Cable Preparation The preparation of the cable differs acc ording to whether or not the shielding wire is to be connected to the FG.
Appendix E Cable with Shielding Wire Not Connected to FG (1) Cut the cable to the required length. (2) Remove the ex ternal vinyl insulation from the cable with a razor blade. T ake c are not to damage the s hielding underneath. (3) Cut back t he shielding wir e with s ciss ors.
Note Appendix E Connector Cover Assembly Assemble the connector cov ers as s hown in the diagram below . End c onnected to FG Alumi num foi l tape End not c onnected to FG Preparing RS-232C .
Appendix F APPENDIX F Connecting to an RS-232C/RS-422 Converter Unit (1:1) By us ing an RS-232C/RS-422 conv erter unit (NT-AL001), R S-232C can be converted to RS-422A, allowing long- - distance communication of up to 500 m. Connection Method OMRON PC RS-232C cable (max.
Appendix F RS-422A Cable Wiring 3 4 5 6 Pin No. Abbrev. SDA SDB RDA RDB RS-422A terminal block Shielding wire NT -AL001 NT-AL001 RS-422A terminal block 3 4 5 6 FG SDA SDB RDA RDB 1 Abbrev.
Reference Appendix G APPENDIX G Function Restri ctions Depending on the Support T ool When using the dir ect c onnection func tion, sc reens c an be created by using the conventional support tools indi- cated below . NT series NT20M/NT2000M/NT600M support tool (Ver .
Note Appendix H APPENDIX H Making the Cable for Connection to the Support T ool Make the connection c able for connection to the s upport tool by referring to the following explanation. Parts Required The table below indicates the recommended par ts for making the c onnection cable.
Appendix H With a 9-pin Connec tor Shielding wire 2 3 4 5 9 1 2 3 7 8 5 SD RD RS CS SG RD SD RS CS SG Personal computer side PT tool connect or side When making the connection cable, us e the following recommended parts .
Appendix I APPENDIX I NT600S Internal Processing When Host/NT link or C200H dir ect is used, the following processing is executed ins ide the NT600S.
Appendix I Number of words for screen element registration The number of wor ds used for sc reen element regis tration is as follows . Allocated wor ds : Number of words Allocated bits : Number of words calculated by summing the number of bits in e a c ha r e aa n dt a k i n g 1w o r dt o b e1 6b i t s .
Reference Reference Appendix I Only the bit and numeral/charac ter-str ing memory table data of elements current- ly being us ed in the sc reen display is written to the PC. If the contents of a numer- al/character -string memory table that is not being used for dis play c hange, the new data is not written to the PC.
Appendix J APPENDIX J Model List PT Model Specification NT600S-ST121-EV Beige, LCD type NT600S-ST121B-EV Black, LCD type NT600S-ST21 1-EV Beige, EL type NT600S-ST21 1B-EV Black, EL type Host.
Note Appendix J CPUs (For Connection Via a Host Li nk) Model Specification PC T ype C20H C28H C40H C60H Features a 9-pin connector for RS-232C connections C-seri es C20H C28H C40H C60H CPM1-10CDR- CPM1-20CDR- CPM1-30CDR- Connect an RS-232C adapter to the peripheral port.
Note Note Appendix J CPUs (For Connection Via an NT Li nk (1:1)) Name Model PC T ype CPM1-10CDR- CPM1-20CDR- CPM1-30CDR- Connect an RS-232C adapter to the peripheral port.
Appendix J CPUs (For Connection Via a C200H Dir ect Communicati on) Name PC T ype C20H C28H C40H C60H C-series C20H C28H C40H C60H C200H-CPU01-E C200H-CPU03-E C200H-CPU1 1-E C200H-CPU21-E C2.
Appendix J Parts Used for Connection Cables with connector s Model Cable Length Applicable Units Communication M ethod XW2Z-200S 2m Host link units w ith 25-pin H o s t l i n k XW2Z-500S 5m .
Appendix K APPENDIX K Option List Replaceable Backlight ... NT600S-CFL01 This is a backlight for replacement purpos es. Reflection-Suppressing Protective Sheet ... NT600M-KBA04 Stuck to the display to pr event it from being soiled. The entire sheet is colorles s and transparent.
Reference Appendix K Chemical-resistant Cover .. T ype NT600S-KBA01 Covers the front panel and protects it from chemical agents. The entire sheet is milky white and made of silicone rubber . The protection the cov er affords is summarized below.
Note Appendix K C200H Interface Unit ... NT-LB122 This is a host interface unit for exec uting direct communic ation. Battery ... 3G 2A9-BA T08 This is a lithium battery used for memory backup. The disposal of the batteries and backlight may be regulated by national or local authorities.
Appendix L APPENDIX L PC Memory Map OMRON C-Series Memory Map Area IR Area HR Area AR Area Link Relay Area Tim er/Count er Area DM Area Ladder type C20H C28H C40H C60H 0000 to 0255 0000 to 0.
Appendix M APPENDIX M Special Characters English Char acter Codes Pin 2 of SW2 must be ON to enable English language messages to us e the following codes. Example: Hex c ode is represented by 30, dec imal code by 48, and character by 0. 30 0 48 Code 20 and 32 in the table r epresents a spac e, as indic ated by “ SP”.
Hex Digits 1st 2nd 2- 3- 4- 5- 6- 7- 8- 9- -0 20 SP 30 0 40 @ 50 P 60 ‘ 70 p 80 Ç 90 É 32 48 64 80 96 11 2 128 144 -1 21 ! 31 1 41 A 51 Q 61 a 71 q 81 ü 91 æ 33 49 65 81 97 11 3 129 14.
Note Appendix M Hex Digits 1st 2nd A- B- C- D- E- F- -0 A0 á B0 C0 D0 E0 α F0 ≡ 160 176 192 208 224 240 -1 A1 í B1 C1 D1 E1 β F1 161 177 193 209 225 241 -2 A2 ó B2 C2 D2 E2 Γ F2 ≥ .
.
INDEX A Allocatable bits and words 154 .................. Allocated bit 13 ............................... Allocated word 13 ............................. Alternate (touc h switch) 185 .................... Automatic reset func tion 89 ......
Creating s creen data 1 15 ....................... D DIP switc h settings 107 ........................ DIP switch 28, 40 ............................. Data memory ( DM) 183 ........................ Decimal fraction parts 148 ................
K Key pres s sound 93 ........................... L LCD 264 ..................................... LSS 39, 40, 41, 44 ............................ Lamp and touch switch display status enquiry 213 ................................... Lamp and touch switch display status response 219 .
POWER 102 ................................. PT battery status res ponse 221 ................. PT operating s tatus 197 ........................ PT st atus c ontrol area 18, 156, 192 ............. PT status enquiry 216 .......................
Solderless terminal 29 ......................... Specify c haracter enlargement 223 .............. Specify dis played charac ters 226 ................ Standard 140 ................................. Start-up sc reen 1 19 .....................
.
Revision History NT -series Programmable T erminal Operation Manual A manual revision code appears as a suffix to the catalog number on the front cov er of the manual. Cat. No. V022-E3-1 Revisi on code The following table outlines the changes made to the manual during each r evision.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Omron V022-E3-1 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Omron V022-E3-1 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Omron V022-E3-1, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Omron V022-E3-1 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Omron V022-E3-1, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Omron V022-E3-1.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Omron V022-E3-1. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Omron V022-E3-1 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
