Manuel d'utilisation / d'entretien du produit Class B Transceiver NAIS-300 du fabricant Navico
Aller à la page of 24
N A I S 3 0 0 MANUAL NAVICO NAIS-300 Class B Transceiver English.
2 Contents The technical data, information and illustrations contained in this publication were to the best of our knowledge correct at the time of going to print. W e reserve the right to change specications, equipment, installation and maintenance instructions without notice as part of our policy of continuous development and improv ement.
Contents 3 Contents 1 Introduction 5 1.1 Gener al overview 5 1.2 SimNet/NMEA2000 6 2 I ns t a l l at i o n 7 2.1 Gener al 7 2.2 Mounting 7 2.3 Cabling 8 2.4 SimNet/NMEA2000 cable 9 SimNet (300-N model only) 9 NMEA2000 (300-L model only) 10 2.5 NMEA0183-HS (RS232) 10 2.
4 Contents RX 18 4.3 Enable/disable switch (Silent Mode) 18 5 Appendix 19 5.1 Maintenance 19 5.2 T roubleshooting 19 5.3 Accessories 19 5.4 Product specications 2 0 5.
Introduction 5 1 Introduction 1.1 General overview The NAIS-300 is a Class B T ransponder that’ s purpose is to transmit the position and other information about y our vessel, to other AIS equipped v essels. It is housed in a rugged waterproof enclosure to withstand the rigors of the marine environment.
6 Introduction 1.2 SimNet/NMEA2000 SimNet is Navico’ s proprietary high speed data bus network compatible with NMEA2000. It provides intelligent sharing of data and control information between a wide range of marine electronics and instruments.
Installation 7 2 I n s t a ll a ti o n 2.1 General The NAIS-300 is designed to be mounted on a flat surface somewhere out of sight, but easily accessible. However , to determine the best possible location, you need to consider how and where, you are going to run the cabling from the sides of the unit.
8 Installation 2.3 Cabling Once you hav e secured your NAIS-300 to a flat surface, you will need to connect the power , SimNet/NMEA2000 and RS232 cables supplied with the unit. The RS485 cable and switch are not supplied, but would be fitted in the same manner .
Installation 9 C h o o s e t h e n i p p le s di r e ct l y a b o v e t h e pa r t s o f t h e c o n n e c to r yo u w an t t o wi r e i n t o a n d c u t o f f t h e t o p s e c t i o n t o t h e re q u ir e d d i a me t e r .
10 Installation NMEA2000 (300-L model only) With the supplied cable connected to the NAIS-300, connect the other end into the supplied T -connector , then connect this into the vessels NMEA2000 network.
Installation 11 The cable can be routed in the molding to drop down directly underneath, or by breaking out the thin traps, the cable can be routed out of the side of the antenna. Alt er nat iv el y , th e ant enn a ma y b e fix e d o n a s tan da rd 1” thr ea ded mo un tin g pol e ( No t s up pli ed) .
12 Installation Th e mo s t im p o rt a n t f a ct o r i n th e pe r f or m a n ce o f a n y AI S tr an s ce i v e r w i l l b e t h e q u a li t y an d p os i t io n i ng o f t h e an t e nn a .
Installation 13 The antenna cable should terminate in a standard marine PL259 plug fitting. Connect the antenna plug to the socket on the side of the unit and screw the retaining collar down. Figure 2.3. To avoid possible water damage to the transceiver, it is recommended that all cables are looped to provide a drip path.
14 Installation.
Configuration 15 3 Conguration 3.1 General Before the NAIS-300 can become fully functional, it will be necessary to load the following information about your vessel into the unit: V essels Name Cal.
16 Configuration For security reasons the MMSI of the vessel cannot be changed once programmed. Do not programme the MMSI unless you are certain you have the correct information. Please check the number entered carefully. If the MMSI programmed is incorrect the AIS transponder will need to be returned to the supplier for factory reset.
Operation 17 4 Operation 4.1 General The NAIS-300 has a limited user interface, consisting of a transmit enable/disable switch, (not supplied), and four indicators on the top of the unit, they are: PWR [Green] - P ower/GPS Lock Status/Silent Mode BIIT [R ed] - Built In Integrity T est TX [Y ellow] - T ransmit RX [Blue] - AIS Message R eceived 4.
18 Operation 6 flashes - noise threshold exceeded 7 flashes - voltage supply fault The “ BII T” me ssa ge wi ll re mai n the re un til th e fau lt is cle ar ed by th e N AI S- 300 ci rc uit ry , or the u nit ha s bee n rep ai red . TX After the initial five seconds the LED will then go out.
Appendix 19 5 Appendix 5.1 Maintenance P eriodically check that the cables are secure and that the connectors have not work ed their wa y loose. 5.2 Troubleshooting These simple checks should be carried out before seeking technical assistance and may sa ve time and expense.
20 Appendix 5.4 Product specications AIS Type Class B for use on non-SOLAS cr aft VHF Receiver R eceiver type Dual TDMA (shared DSC) Sensitivity < -107dBm for 20% PER T ransmit power 2W att T ype Approv al Meets IEC62287-1 GPS Receiver R eceiver type Integral 16 channel receiv er EMC IEC60945 Power V oltage 10.
Appendix 21 NMEA2000 AIS PGNs 129038 Class A P osition R eport 129039 AClass B P osition R eport 129040 Class B Extended P osition R eport 129792 DGNSS Broadcast Binary Message 129793 UT C and Date R .
22 Appendix 5.5 Dimensions Figure 5.1 - NAIS-300 dimensions Figure 5.2 - GPS Antenna dimensions 5.6 Service and warranty If it is necessary to hav e a unit repaired, please contact your local authorized dealer . F or worldwide warr anty details and a list of authorised Navico agents please refer to the W arranty Card supplied with this unit.
Appendix 23 English Hereby , Navico AS declares that this NAIS-300 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Finnish Navico AS vakuuttaa täten että NAIS-300 tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
www.navico.com.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Navico Class B Transceiver NAIS-300 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Navico Class B Transceiver NAIS-300 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Navico Class B Transceiver NAIS-300, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Navico Class B Transceiver NAIS-300 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Navico Class B Transceiver NAIS-300, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Navico Class B Transceiver NAIS-300.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Navico Class B Transceiver NAIS-300. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Navico Class B Transceiver NAIS-300 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
