Manuel d'utilisation / d'entretien du produit 825 du fabricant Napco Security Technologies
Aller à la page of 15
0 1880, NAPCO OPERATING GUIDE FOR YOUR MAGNUM ALERT-825/ MAGNUM ALERT-825HS SECURITY SYSTEM NAPCO.
Please read this guide thoroughly to familiarize yourself with your new security system. Keep this booklet handy for future reference. Note especially the ALARM PLAN on page 15. Your alarm specialist will help you fill it out and explain the various features and operating procedures for your new Magnum Alert-825/825HS.
Abort Delay A delay period that allows the system to be reset before it reports to a central station. Alarm Plan ldentifies the areas of your premises pro- tected by each zone of protection and lists zone features.
lndicator Lights ARMED/MEMORY (Red) l Steady- system is armed. l Flashes - alarm condition. Flashes indicate the number of zone(s) which were violated. (see page 5, Key 2) STATUS (Green) l Steady - system is disarmed, all zones okay. l Flashes - a non-24 hour zone is in trouble.
Keys NOTICE:Keys1 , 2,3,4,5,9 and S must be held down for 2 seconds (until mini-sounder beeps) to per- form their desianated ‘Hold- Down " (“Key”) functions. Key 1: TEST Momentarily sounds the burglar alarm from the battery. If no alarm is heard, or if it is weak, the battery may need replacing.
Your Magnum Alert-825/825HS Security System has three basic components: 1. Zones Your system is capable of monitoring up to six separate areas of your premises, including Am- bush/Panic and Auxiliary zones. Each zone is an independent cir- cuit that protects a specific area of your premises.
The Digit-Key Keypad All security system operations are carried out at the keypad. Each key hasaspecialfunction o f its own (see “CONTROLS” page 5) plus the ability to arm and disarm the system when they are used in a preselected combination (codes).
Checking AC Power If the three lights of your keypad are blinking slowly, you have lost AC power. Check to see if there has been a general power outage, or if the Control Center’s trans- former is disconnected. If you must operate without AC power, press Key9 to stop the lights from blink- ing.
If trouble is encountered on a zone programmed as a Priority- with-Bypass Zone however, enter your code to silence th e Mini- Sounder and disarm; hold down Reset Key 9 until it beeps (this will bypass the alarm condition); then enter your code to rearm.
Arming Wlth Selective Zone Shunting Your alarm specialist may have opted for one or more zones that can be selectively shunted (removed) from the system. Since a shunted zone cannot cause an alarm, you may wish to use this feature to turn OFF the interior areas while arming, and keeping your perimeter zones (windows, doors, etc.
Your Alarm Specialist may have programmed your security system to be monitore d by a central station. The built-in digital communicator can transmit emergency signals to the central station 24 hours a day.
Abort Delay Note which zones on your alarm plan have abort delay. This is a delay that enables you to reset the system before a zone condition report is sent to the central station. Non-24 hour zone reports are aborted by arming and then disarm- ing. 24 hour zones, however, must first be repaired.
The following information is applicable only where local ordinance permits use of your alarm Control Center for fire detection Controlling Your Fire Circuit If your alarm specialist installed smoke detectors or heat sensing thermostats, you have 24 hour fire protection.
Even with the most advanced fire alarm system, adequate protection requires an escape plan. To pre- pare your plan: Draw floorplans of your building. Show two exit s - a front or back door and a window from each room. (Make sure the window works. You may need a special fire escape ladder if the window is high up.
Zone Area Protected Zone Features Contacts (doom, wlndows, etc.) 1 6 Central Station (Optional) Service Person Telephone Telephone 15.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Napco Security Technologies 825 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Napco Security Technologies 825 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Napco Security Technologies 825, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Napco Security Technologies 825 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Napco Security Technologies 825, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Napco Security Technologies 825.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Napco Security Technologies 825. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Napco Security Technologies 825 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
