Manuel d'utilisation / d'entretien du produit 20150513 du fabricant Master Bilt
Aller à la page of 20
Manual Code: 98151 10001 0521 12-02SS T ool needed for assembly: Phillips Head Screwdriver Approximate assembly time : 60 minutes W ARNING W ARNING Use only outdoors where it is well ventilated. Fuel, such as charcoal briquettes, wood or heat pellets, are not to be used in the unit.
1 GENERAL W ARNINGS AND SAFETY INFORMA TION READ ALL INSTRUCTIONS When using electrical appliances, basic safety precautions should always be followed including the following: • Cannot be operated for more than 3 hours . • Use GFI protected electrical outlet to reduce the risk of electrical shock.
GENERAL W ARNINGS AND SAFETY INFORMA TION • Be careful when removing food from electric grill. All surfaces are HOT and may cause burns. Use protective gloves or long, sturdy cooking tools. • Drip tray is only for the bottom of electric grill. Do not put drip tray on cooking grate this may damage electric grill.
3 GENERAL W ARNINGS AND SAFETY INFORMA TION • Fatty foods (hamburgers,etc.) can have excess grease and cause fl are ups. When cooking fatty foods use a low setting with lid open. • Clean internal base pan before each use. This will cut down on build-up and fl are-ups.
4 P ARTS LIST P ART NO QTY DESCRIPTION P ART NO QTY DESCRIPTION 1 1 Grill Lid 14b 1 Back Panel 2g 1 T emperature Gauge 15 2 Hub Cap 2b 1 T emperature Gauge Base 16 2 Wheel 3 1 Right Side Shelf 17 2 Fo.
P ARTS LIST 5 (B) M6x35 Phillips Head Screw Qty: 2 (F) Bakelite Spacer Qty: 2 (J) M4 Flat W asher Qty: 5 (D) M4x40 Phillips Head Screw Qty: 2 (G) M6x13 Phillips Head Screw Qty: 40 (L) M6x8 Phillips He.
SHORT SIDE FRONT ASSEMBL Y *Note that the front of the grill is actually the shortest width of the bottom storage shelf (12). • BEFORE ASSEMBL Y READ ALL INSTRUCTIONS CAREFULL Y . • ASSEMBLE UNIT ON A CLEAN, FLA T SURF ACE. • T OOL NEEDED: PHILLIPS HEAD SCREWDRIVER • UNP ACK ALL P ARTS AND LA Y OUT IN FRONT OF YOU.
SHORT SIDE FRONT 7 ASSEMBL Y STEP 4 Attach bottom shelf (12) to legs (18) using screws (G) with the feet facing away from right side of the shelf as shown.
8 ASSEMBL Y STEP 5b Repeat step 4a for leg (19, “FL”). STEP 5c Place panel (14b) [the panel with the serial plate] over panels (13) and insert screw (G); into bottom holes.
ASSEMBL Y STEP 6 Insert support (1 1b) into front leg (18, “FR”) with holes facing in- ward. Insert other (1 1a) into back leg (18, “BR”) with holes facing inward. Repeat steps for left side. When all supports are in place screw holes should be facing each other as shown in image.
10 ASSEMBL Y STEP 8 Attach drip tray bracket (8) to grill base (5) using washers (I) and screws (L). 5 8 I I L STEP 9 Position grill base (5) onto seat (22) as shown. Secure using washers (I) and screws (G). 5 5 I I G G 22 22 L (G) M6x13 Phillips Head Screw (L) M6x8 Phillips Head Screw View of grill base (5) positioned on seats (22) from below .
11 ASSEMBL Y STEP 10 Place logo base (28) onto grill base (5). Secure using washers (J) and screws (H). H 28 5 J STEP 11 Attach left bottom hinge (24) to grill base (5) using washers (C) and screws (G). [Welded nut on left bottom hinge (24) should be facing right when secured.
12 ASSEMBL Y STEP 12 From inside grill lid, align holes of left lid hinge (25) to grill lid (1) holes. Secure with screws (G) and fl at washer (C). Repeat step on other side with right lid hinge (26), washer (C) and screw (G).
ASSEMBL Y STEP 14 Attach temperature gauge (2g) and temperature gauge base (2b) to grill lid (1) using wing nut. 1 WING NUT 13 STEP 15 Place bakelite spacer (F) on grill lid (1). Attach handle (27) using washers (J) and screws (D) as shown. Make sure lid handle (27) is slop- ing downward as shown in FIGURE 2 .
14 ASSEMBL Y STEP 17 Place re fl ector plate (9) into bottom of grill base (5). 5 9 STEP 16 Attach left side shelf (6) to both supports (1 1) using screws (G). Repeat step on opposite side with right side shelf (3). GO BACK AND TIGHTEN ALL SCREWS A T THIS TIME.
15 STEP 19 Position cooking grate (20) on top of grill base (5). 20 STEP 18 Attach heating element (4) to grill base (5) using screws (A) as shown. 5 A 4 ASSEMBL Y (A) M5 Thumb Screw Note: The 2 support bars on cooking grate (20) should span left to right, with the grates going front to back.
16 STEP 20 Insert warming rack (21) onto cooking grate (20), with forks of warming rack straddling grate as shown in FIGURE 3. STEP 21 Plug controller (10) into side of grill base (5) from below side shelf (6), coming in at a slight angle, carefully inserting plug while lifting so that top of controller slips into notch in shelf (6).
17 • Inspect hardware and assembled parts on a regular basis to insure grill is in safe working condition. • AL W A YS allow grill to cool completely before handling. • AL W A YS empty drip tray after use only when ashes have completely cooled. • Clean grill, including special surfaces such as cooking grates with mild cleaning agents.
18 LIMITED W ARRANTY Masterbuilt warrants its products to be free from defects in material and workmanship under proper assembly , normal use and recommended care for 90 days from the date of original retail purchase. Masterbuilt warranty does not cover paint fi nish as it may burn of f during normal use.
Masterbuilt Manufacturing, Inc. 1 Masterbuilt Ct. Columbus, GA 31907 Customer Service 1-800-489-1581 www .masterbuilt.com.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Master Bilt 20150513 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Master Bilt 20150513 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Master Bilt 20150513, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Master Bilt 20150513 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Master Bilt 20150513, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Master Bilt 20150513.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Master Bilt 20150513. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Master Bilt 20150513 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
