Manuel d'utilisation / d'entretien du produit WA-410 du fabricant LOREX Technology
Aller à la page of 29
WIRELESS HOME SECURITY SYSTEM Instruction Manual English Version1.0 MODEL: WA-410 www.lorexcctv.com Copyright © 2007 Lorex Technology In c..
Table of Contents Introduction………………………………………… ………………………………….…... 1 System Package…………………………………… ……………………….…. Optional Accessories…………………………………………………… …….
Important Safety Instructions • Read Instructions – All the safety and operating i nstructions should be read before operating this equipment. These instructions should be retained f or future ref.
Introduction Thank you for choosing the Lorex® WA410 Wireless Home Security System. These security systems are high-quality, reliable and versatile. This system has a built in Auto- dialer for increased security.
Planning for Installation 4 The security system is designed to be as flex ible as possible in order to meet your present needs, and also to adapt as your needs change. For the rea son, we recommend that you read and consider the following information and plan your s ystem before installing these devices.
5 Connecting the T elephone Line T o connect the Main Console to the te lephone line, Please follow these steps: 1. Locate the two phone jacks at the top of the main console. These phone jacks are marked “ Phone “ and “ Line “. 2. Connect one end of the telephone cord that came with the system into the connector , labeled” Line”.
Operation – Main Console The Main Console is the heart of the secu rity system. It monitors the sensors and responds according to how it is programmed, whenever a sensor is activated. The illustration shown for the Main Console may look complex at first, however , m ost procedures are straightforward and easy .
13. Armed LED : When the light is ‘on’, the system is armed; When the light is ‘off’, the system is disarmed. 14. LCD Panel : Displays messages 15. Speaker : Sounds alarm and plays back messages 16. Antenna : Used for wireless reception 17. Output Jack : Connects to the external siren 18.
3.1: System Option menu : Press 0 to st art settin g Setting : 0 – T 1 2 3 4 5 6 – P 7 – MSG 8 – DIAL 9 - CODE (1) 0-T : For time setting (Default is 30 se conds.
Setting 5 : The first priority dial in case of Fire. (check with the fire dept if this is acceptable) Setting 6 : The first priority dial in case of Medical help.
Press 1 to change the Install code menu. Setting : Change Code 1 – Install : 1 2 3 4 5 Press 2 to change the Master code menu. Setting : Change code 2 – Master : 1 3 5 2 4 6 3.2: Sequence Programming Menu This menu for code learning establishes a link between all sensors/other wireless devices and the main console.
listed below . It will automatically adv ance to the next sequencing learning order position. 11 7. If the sensor that was learnt into t he main console is s ending a signal during the learning mode, the main console will indicate on the LCD, as shown below and will not allow duplication.
be cleared. Press 3 to go into the clear mode. Clear Sensor 1 – Single 2 - All Press 1 , and key-in the sequence learning order number. Press ENTER , to clear the sensor . Clear Sensor 1 – Single Num: xx Clear Sensor Clear OK Num : xx Press 2 , It will display the w ords “Are you sure ? ”.
z If the password is correct, the main console will emit a long beep sound. (LCD display shown below). Access Granted Master Mode : MASTER A-AWAY H-HOME Now the system will select the arm mode and set the system in either A way arm/Home Arm mode (see below): A - AWA Y : Press the A WA Y button t o set the “ Armed - Away “ alert.
z SP DIAL + 4 , the autodial order is: Preset 4 → Preset 1 → Preset 2 → Preset 3 (Burglary condition) z SP DIAL + 5 , the autodial order is: Preset 5 → Preset 1 → Preset 2 → Preset 3 (Fire.
is answered, it will playback the message 2 times Medical help - It will automatically dial Preset 6 → Preset 1 → Preset 2 → Preset3, phone numbers for 3 c ycles (6, 1, 2, 3).
Remote Control Handset The key chain Remote Control Handset is a convenient way to arm (Home / Away mode) or disarm this system. Before using this dev ice, please program it into the main console via the sequence programming menu. 1. TRANSMIT LED : The LED will light when the device is transmitting 2.
• Press the P ANIC button, to activate the “P ANIC” function. The activation of the “P ANIC” function will immediately trigger the ala rm and auto dialer . 63 REMOTE SENSOR 01 Panic PIR Motion Detector The PIR Motion Detector is designed to detect the movement of objects in a room or hallway .
4. BA TTERY : Remove the Battery cover and insert one 9V alkaline batter y . 5. ARM & HOLDER : For mounting on the wall. 6. BA TTERY COVER Replace the Battery z When the sensor sends a low batter y message to main console, remove the old battery and replace it with a fresh alkaline battery .
Before installing the sensor , consider the following points: z Mount the sensor two meters (6-1/2’) high for best coverage. z Mount the sensor with a 14 degree do wnward incline angle against the wall for optimum range.
Door/Window Detector (for DC 12V battery) 20 Change the Battery When the sensor sends a low battery message to the main console, remove the old battery and replace it with a fresh alkaline battery . The low batter y message on the LCD is shown below Button function 1.
1. The LED on the sensor will flash once when the sensor is triggered. 2. There cannot be a gap gre ater than 1/4 inch (5 mm) bet ween the magnet sensor and the magnet, otherwise, the sensor will not work properly . Enter the installer pa ssword and press the “1” button to activate the “ Sequence Programming Menu”.
INSTALLING POSITION REFE RENCE FOR DOOR/WINDOW DETECTOR Mini Siren The siren is an effective deterrent to intruders. Choose a location inside your home where the siren is not plainly visible, but can be heard throughout the house.
1. Plug the wire into the control panel OUTPUT JACK 2. Cord length – 8 meters. 3. Loudness output – 110 db. 4. Dimensions – 3.7 x 4.5 x 2 (cm) 5. Weight – 120g (including the cord) Summary of Program – Main Console Use the following form to record your programming choices for future reference.
Item Descriptions Install Code Master Code Exit Time Alarm Time Entry Time Auto-dialing Mode Preset Telephone No. for Auto-dialing : No. 1 Name T el. No. No. 2 Name T el. No. No. 3 Name T el. No. No. 4 (Burglary Emergenc y) Name T el. No. No. 5 (Fire Emergency) Name T el.
Learning Number Place of Installation Zone Label Learning Number Place of Installation Zone Label 05 2F-xx room Window 1 Learning Number Place of Installation Zone Label Learning Number Place of Insta.
Items Specifications Frequency - 303Mhz or 433Mhz Power Source - AC120V, DC 12V Power Consumption - 70mA (idle), 170mA (activated) Back-up Battery (Optional) - Approximate 7 hours ( NO AC adaptor) Tem.
27 “Installation template for wall mounting of main control panel ” 1. Use the template on the right to mark positions for mounting screws to install the main control panel o n the wall. 2. Once the mounting screw posit ions have been ma rked, drill 3/16” pilot holes and install the plastic wall an chors supplied.
It’s all on the web Product Information User Manuals Quick Start Guides Specification Sheets Software Upgrades Firmware Upgrades Lorex Technology I nc.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté LOREX Technology WA-410 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du LOREX Technology WA-410 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation LOREX Technology WA-410, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le LOREX Technology WA-410 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le LOREX Technology WA-410, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du LOREX Technology WA-410.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le LOREX Technology WA-410. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei LOREX Technology WA-410 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
