Manuel d'utilisation / d'entretien du produit C/A210 du fabricant Logitek Standard Elec. Cable Manufacturing
Aller à la page of 18
INST ALLA TION AND OPERA TION MANUAL W ARNINGS • Hot! Do not touch! The glass and surfaces of this appliance will be hot during operation and will retain heat for a while after shutting off the appliance. Severe burns may result. • Carefully supervise children in the same room as appliance.
2 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. C ontents t esting i nforma tion .........................................................................3 g eneral s afety P reCautions .........................................................
3 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. t esting i nforma tion This manual describes the installation and operation of the Performer™ C/A210 non-catalytic wood heaters. These heaters meet the U.S. Environmental Protection Agency’ s emissions limits for wood heaters sold on or after July 1, 1990.
4 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. D rafting Y our wood stove is dependent upon a properly functioning chimney for optimum per formance. It is a high efficiency appliance that loses much less heat up the chimney than older applian ces and firep laces.
5 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Please be patient with the heat output of your stove for the first few weeks. The steel will go throu gh a curing process that eliminates moisture, which is deep in the steel and firebrick. This moisture will reduce initial heat output of your stove and may make it difficult to start.
6 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. B riCk i nst alla tion P erformer ™ C/a210 B riCk i nst allation CAUTION: Wear gloves during brick installation in case of sharp edges behind the stove.
7 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Model F (1) G H J(2) M C/A210 18” 45 0m m 12-1/4” 31 1m m 19 ” 48 3m m 4-1/2” 1 14m m 42 -1 /8 ” 10 70 m m C/A210 w/ mantel and/or sid.
8 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. C himney r equirements The Performer™ C/A210 inserts are approved for use in masonry fireplaces built to UBC Chapter 37 or equivalent with a minimum 22” (559mm) opening at the front of the fireplace.
9 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. i nst alla tion P roCeDure - f aCtor y -B uil t Z ero C learanCe f irePlaCes Fireplace and Chimney Requirements The Performer™ C/A210 insert m.
10 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Chimney Liner Installation Remove the existing chimney cap and install a stainless steel liner into the chimney (if a special section has been used or drilled to attach to the insert, it must be the bottom piece).
11 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. o Pera ting h ints 1. Burn only dr y , well-seasoned wood for maxi- mum heat output. In some states it is illegal to burn wet wood or anything other than clean, dry wood products.
12 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. s t arting anD m aint aining a f ire Be sure to clean the Nickel or Gold Plated door with Win- dex brand cleaner and a ver y soft cloth to remove any fingerprints and residues prior to the first fire.
13 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Keeping freshly loaded wood away from the window will also help. Load fresh logs in the rear of the firebox. Build-up tends to occur first on the right side of the window . This is caused by the swirling motion of the exhaust gases similar to water running down a drain.
14 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 4. Operate your stove as much as possible in the low to medium burn ranges. 5. Do not lower the draft setting so low as to compl etely extinguish the flames in the firebox. Check for at least some small flames 20 minutes after setting the draft control.
15 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Exp eri men t with diff ere nt loa din g config ura tio ns to achi eve longer burns. T r y loading the wood from side to side and nesting it in the ashes to prevent airflow under and around the wood.
16 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. t rouBleshooting Problem Solution POOR DRAFT : Extend chimney in length or have the chimney realigned to the proper size flue. Oversized chimneys normally have poor drafts. Remember , the stoves’ draft depend solely on the natural draft of the chimney (See Drafting section on page 4).
17 D o ’ s anD D on ’ ts DO NOT : Install or operate this stove before reading this manual. DO NOT : Close the draft beyond the point at which the flames are completely extinguished. DO NOT : Open the stove door without fully opening the draft first.
The manufacturer reser ves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information. 1110 West T aft Avenue • Orange, CA 92865 Printed in U.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Logitek Standard Elec. Cable Manufacturing C/A210 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Logitek Standard Elec. Cable Manufacturing C/A210 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Logitek Standard Elec. Cable Manufacturing C/A210, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Logitek Standard Elec. Cable Manufacturing C/A210 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Logitek Standard Elec. Cable Manufacturing C/A210, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Logitek Standard Elec. Cable Manufacturing C/A210.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Logitek Standard Elec. Cable Manufacturing C/A210. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Logitek Standard Elec. Cable Manufacturing C/A210 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
