Manuel d'utilisation / d'entretien du produit WAP51AB du fabricant Linksys
Aller à la page of 28
Instant Wireless TM Series Dual-Band Wireless Access Point Use this guide to install: W AP51AB User Guide.
COPYRIGHT & TRADEMARKS Copyright © 2002 Linksys, All Rights Reserved. Linksys is a register ed trademark of Linksys. Instant Wireless is a trademark of Linksys. Micr osoft, Windows, and the Windows logo are r egistered trademarks of Microsoft Corporation.
Dual-Band Wireless Access Point Chapter 1: Introduction The Instant Wireless TM Dual-Band Wir eless Access Point Install an access point that protects your infrastructure in vestment without lim- iting you to a single type of wireless technolo gy . The Instant W ireless™ Dual- Band W ireless Access P oint w orks simultaneously with both 802.
Dual-Band Wireless Access Point 3 Chapter 2: Planning Y our Wireless Network A wireless LAN is a group of computers, each equipped with one Instant W ireless™ Series adapter . Computers in a wireless LAN must be conf igured to share the same radio channel.
Dual-Band Wireless Access Point Instant Wireless TM Series Chapter 3: Getting to Know the Dual-Band Wireless Access Point The Access P oint’ s por ts, where a netw ork cable is connected , are located on the Access P oint’ s back panel.
Chapter 5: Setting Up the Dual- Band Wireless Access Point No w that you’ ve connected the Access P oint to your wired netw ork, you are ready to begin setting it up. This Setup W izard will take you through all the steps necessary to conf igure the Access P oint.
9 3. The follo wing screen, shown in F igure 5-2, displays ho w the Access P oint is conf igured in this Setup W izard. Optimally , you should perform this setup through a PC on your wired netw ork. Click the Next button to con- tinue or Exit to exit the Setup Wizard.
The WEP key can consist of the letters “ A” through “F” and the numbers “0” through “9” and should be 10 characters in length for 64-bit encryption, 26 characters in length for 128-bit encryption, or 32 characters in length for 152-bit encryption.
9. As shown in F igure 5-8, the Basic Settings screen for your 2.4 GHz/802.11b wireless products will appear . Enter your wireless netw ork’ s SSID and select the channel at which the netw ork broadcasts its wireless signal. Then, click the Next button to continue or Back to return to the pre- vious page.
Dual-Band Wireless Access Point 13. At this point, the conf iguration performed with the Setup W izard is com- plete, as sho wn in F igure 5-12. T o conf igure any other Access P oints in your netw ork, you can run this Setup W izard again. Click the Exit button to exit the Setup W izard.
16 • Static IP Addr ess. This IP address must be unique to your netw ork. (The default IP address is 192.168.1.250. As this is a priv ate IP address, there is no need to purchase a separate IP address from your service pro vider .) V erify the address and click the Appl y button to sav e changes.
From the pull-do wn menu, select the type of WEP encr yption you wish to use. If you are using 5GHz/802.11a wireless technolo gy , you will need to enter the ke y manually . If you are using 2.4GHz/802.11b wireless technolo gy and wish to use a WEP Passphrase, it can be a maximum of 16 alphanumeric characters.
Dual-Band Wireless Access Point The “Status” tab, sho wn in Figure 6-8, will displa y cur rent information on the Access P oint, its settings and perfor mance. • Firmw ar e V ersion. This displays the current version of the Access P oint’ s f irmw are.
Dual-Band Wireless Access Point UPGRADING FIRMW ARE: Before upgrading the Access P oint’ s f ir mware, be sure to do wnload the f ir mware from Linksys’ s website at www .linksys.com. Once that is done, click the Upgrade Firmw ar e link on the Help T ab.
Dual-Band Wireless Access Point • F ragmentation Length. This specif ies the maximum size a data packet will be before splitting and creating a new pack et and should remain at its default setting of 2,346. A smaller setting means smaller packets, w hich will create more packets for each transmission.
Dual-Band Wireless Access Point Appendix A: T roubleshooting This chapter pro vides solutions to problems usuall y encountered during the installation and operation of the Access P oint. Read the description belo w to solve y our problems. If y ou can’ t f ind an ans w er here, check the Linksys w eb- site at www .
Dual-Band Wireless Access Point What is ESSID? An Infrastructure conf iguration could also support roaming capability for mobile w orkers. More than one BSS can be conf igured as an Extended Service Set (ESS).
Dual-Band Wireless Access Point Y ou ma y also try using different channels, as this ma y eliminate interference af fecting onl y one channel. Also, due to FCC regulations, more po w er ma y be transmitted , using 802.11a, on channels 52, 56, 60 and 64, than on the lo wer channels.
Dual-Band Wireless Access Point The follo wing instr uctions are pro vided as examples for reference only . F or complete instructions on installing and troubleshooting TCP/IP and IPX, con- sult your W indo ws operating system documentation. 1. Click the Start button, select Settings , and open the Control P anel .
Dual-Band Wireless Access Point 2. When the Netw ork windo w appears, click the Protocols tab . Then, click the Add button. 3. Find the IPX/SPX pr otocol in the Select Networ k Protocol f ield. Click it once and click the OK button. 1. At the W indo ws 2000 desktop, right click My Network Places and select Pr operties .
Instant Wireless™ Series 4. Select NWLink IPX/SPX/NetBIOS Compatible T ransport Protocol from the list and click the OK button. 5. When the Netw ork windo w reappears, click the OK button. Restar t your computer . NWLink IPX/SPX/NetBIOS Compatible Transport Protocol has no w been successfully installed.
quently . Using very shor t leases, DHCP can dynamicall y reconf igure netw orks in which there are more computers than there are a vailab le IP addresses. DHCP supports static addresses for computers containing W eb servers that need a permanent IP address.
The IEEE fosters the de velopment of standards that often become national and international standards. The organization pub lishes a number of journals, has man y local chapters, and sev eral large societies in special areas, such as the IEEE Computer Society .
Dual-Band Wireless Access Point Serv er - Any computer w hose function in a network is to pro vide user access to f iles, printing, communications, and other ser vices. Softwar e - Instr uctions for the computer . A series of instructions that perfor ms a particular task is called a "program.
Dual-Band Wireless Access Point Appendix D: Specifications Standards IEEE 802.3, 802.3u, 802.11a and 802.11b Channels 802.11a 8 Channels (US, Canada) 802.
Dual-Band Wireless Access Point 47 Appendix E: W arranty Information BE SURE T O HA VE Y OUR PR OOF OF PURCHASE AND A BARCODE FR OM THE PR ODUCT’S P A CKAGING ON HAND WHEN CALLING.
Appendix F: Contact Information F or help with the installation or operation of this product, contact Linksys T echnical Suppor t at one of the phone numbers or Inter net addresses belo w . Sales Information 800-546-5797 (LINKSYS) T echnical Suppor t 800-326-7114 RMA Issues 949-261-1288 Fa x 949-261-8868 Email support@linksys.
© Copyright 2002 Linksys, All Rights Reser ved. http://www .linksys.com.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Linksys WAP51AB c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Linksys WAP51AB - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Linksys WAP51AB, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Linksys WAP51AB va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Linksys WAP51AB, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Linksys WAP51AB.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Linksys WAP51AB. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Linksys WAP51AB ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
