Manuel d'utilisation / d'entretien du produit SF6 du fabricant ion science
Aller à la page of 17
INSTRUCTION M ANUAL GAS-CHECK SF 6 AN INSTRUMENT FOR THE LOCATION AND MEASUREMENT OF LEAKS IN SF 6 FILLED ELECTRICAL S W ITCHGEAR. User Manual iss 01 Software-Version V1.
Page 1 Contents: Software version V1.39BB Subject Description Page 3.0 Gen eral 2 3.1 Safety 2 4.0 System Properties/introduction 3 4.1 Console controls 3 5.0 Handgun displays and controls 4 5.1 Handgun analogue display 4 5.2 Handgun display LED’s 4 6.
Page 2 12.0 User setup 12 12.1 Peak hold (gauge) 12 12.2 Peakhold (screen) 12 12.3 Display units 12 13.0 Desen Factor 1 13 13.1 Desen Factor 2 13 13.2 Standby mode 13 14.0 Standby delay 13 14.1 RS232 Protocol 13 14.2 Sound type 14 14.3 Sound begins at 14 14.
Page 3 4.0 SYSTEM PROPERTIES: Introduction: GAS-CHECK SF6 is a portable, mains-independent instrument for leak detection and leak measurement of SF6 gas. Although designed for SF6, other gases with a high affinity for electrons, such as refrigerant R12 may also be detected.
Page 4 5.0 Handgun Displays and Con trols: % A l a r m O F F 9 0 8 0 7 0 6 0 5 0 4 0 3 0 2 0 1 0 0 The following controls are found on the hand unit: 5.1 Analogue gauge: displays the response to leaks in %, rather than an absolute value (displayed on the touch-screen), and shows the leak rate in the form of a percentage of the alarm value.
Page 5 6.0 HANDGUN BUTTONS: S QUARE : This has two functions: MEASURE MODE and SEARCH (bar graph) MODE. On power-up the SEARCH mode is automatically selected, the touch screen displays a bar graph. This is ideal for fast and ultra low-level leak detection (~10 E-8cc/sec).
Page 6 7.0 GETTING STARTED: This assumes you have just received the instrument and it is NOT powered up. 1 Plug in the sensor and connect the ha ndgun to the console. Align the red marks and press home. 2 Connect to a mains electrical supply AC 85-265V.
Page 7 7.3 LOW FLOW ERROR: The flow through the sensor is controlled by the vacuum pump. The level of vacuum required to maintain the required flow can be seen in the lower LH screen. Should the sample intake of the sensor be partially or totally blocked, the instrument will first try to compensate by increasing the vacuum.
Page 8 8.1 USER SETUP : This paragraph describes the parameters that determine the behaviour of the instrument. The first step is always. Activating the Menu System. In normal operation, the instrument can be taken to programming mode by simply touching the touch-screen.
Page 9 9.2 D ata Printout If readings were stored using the STORE key on the hand unit, these can be printed or transferred to a computer. After printout, the data memory is cleared. See section 16.5 page 15 for ISL supplied printer settings and information.
Page 10 10.2 F orce Operator ID by key code If selected, a password (key code number) entry screen is opened after power up. The operator is now required to enter his personal key code. If nothing or an invalid key code is entered, data printout is not possible.
Page 11 11.0 C alibration The GAS CHECK SF6 is unique in that completely separate values are stored for each of the display modes. This means that if you want to measure ppm or gm/yr these values must be calibrated before use. Calibration follows the same easy routine as with cc/sec calibration using the Portable Reference Leak .
Page 12 12.0 U ser set-up This gives access to a number of parameters which determine the behaviour of the instrument. They are described as follows and all are selected using the up/down arrows and changed using the -/+ buttons. 12.1 Peakhold (gauge).
Page 13 13.0 Desens Factor 1. Factory pre-set at x5. On a high or ‘gross’ leak, press the GREEN handgun pad once. This desensitises by x5; the Green (special) lamp will flash. 13.1 Desens Factor 2. Factory pre-set at x5. Pressing the GREEN handgun pad again invokes a further desensitise, the lamp will flash faster.
Page 14 14.2 Sound type Using the +/- buttons select sound output you prefer. HARMONIC or TRADDITIONAL. If more than one instrument is used in a confined space, it may be useful to set them to different sound types. 14.3 Sound begins at This allows you to set the display value at which the sound begins.
Page 15 15.1 Probe/Sensor Li fetime/filter: Sensor life is presently estimated to be 200 hours of continuous use in a normal industrial atmosphere. Sensor life is affected only by contamination in the air sample being drawn through probe. Therefore it is dependent on ambient conditions.
Page 16 16.4 Settings on despatch as found in U ser Setup Instrument serial Number P1 Date Peak Hold (gauge) 0.5 s Peak Hold (screen) AUX DISP Display Units E-6 ml/s Desen.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté ion science SF6 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du ion science SF6 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation ion science SF6, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le ion science SF6 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le ion science SF6, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du ion science SF6.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le ion science SF6. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei ion science SF6 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
