Manuel d'utilisation / d'entretien du produit CARB 340 du fabricant Husqvarna
Aller à la page of 36
Operator's manual (CARB, EP A) Please read these instructions carefully and make sure you understand them before using the saw. 3 40/34 5/3 5 0 101 90 07-95.
2 – English KEY T O SYMBOLS Symbols Switch off the engine by moving the stop switch to the STOP position before carrying out any checks or maintenance. Always wear approved protective gloves. Regular cleaning is required. Visual check. Protective glasses or a visor must be worn.
English – 3 CONTENTS Contents Key to symbols ............................................................... 2 Safety instructions Personal protective equipment ............................................ 4 Chain saw safety equipment ..............
4 – English ! CHAIN SA W SAFETY EQUIPMENT This section explains the various safety features of the saw, how they work, and basic inspection and maintenance you should carry out to ensure safe operation. (See the ”What is what?” section to find out where these components are on Your saw).
English – 5 1 Chain brake and front hand guard YOUR chain saw is equipped with a chain brake that is desig- ned to stop the chain immediately if you get a kickback. The chain brake reduces the risk of accidents, but only You can prevent them. Take care when using your saw and make sure the kickback zone of the bar never touches any object.
6 – English 6 The way the chain brake is triggered, either manually or automatically, depends on the force of the kickback and the position of the chain saw in relation to the object that the kickback zone of the bar strikes.
English – 7 SAFETY INSTRUCTIONS The muffler gets very hot in use and remains so for a short time afterwards. DO NOT TOUCH THE MUFFLER IF IT IS HOT! 6 Stop switch Use the stop switch to switch off the engine. 7 Muffler The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user.
8 – English ! SAFETY INSTRUCTIONS 3 Checking the inertia brake release Hold the chain saw over a stump or other firm object. Let go of the front handle so that the bar falls onto the stump. When the bar hits the stump the brake should be applied. 4 Checking the brake trigger Start the chain saw and place it on firm ground.
English – 9 SAFETY INSTRUCTIONS 4 Right hand guard Check that the right hand guard is not damaged and that there are no visible defects, such as cracks. 5 Vibration damping system Regularly check the vibration damping units for cracks or deformation Make sure the vibration damping units are securely attached to the engine unit and handles.
10 – English ! 7 Muffler Never use a chain saw that has a faulty muffler. Regularly check that the muffler is securely attached to the chain saw. If the muffler on your saw is fitted with a spark arrestor mesh this must be cleaned regularly. A blocked mesh will cause the engine to overheat and may lead to serious damage.
English – 11 ! SAFETY INSTRUCTIONS C Some terms that describe the bar and chain When the cutting equipment supplied with your saw becomes worn or damaged you will need to replace it. Use only the type of bar and chain recommended by us. See the ”Technical data” section to find out which equipment is recommended for your saw.
12 – English SAFETY INSTRUCTIONS ! 2 Sharpening your chain and adjusting raker clearance The risk of kickback is increased with a badly sharpened chain! A General information on sharpening cutting teeth • Never use a blunt chain.
English – 13 ! C General advice on setting raker clearance • When you sharpen the cutting teeth you reduce the RAKER CLEARANCE (cutting depth). To maintain cutting performance you must file back the raker teeth to the recommended height. See the ”Technical data” section to find the raker clearance for your saw chain.
14 – English 1 Undo the bar nuts that hold the clutch cover and chain brake, using the combination spanner. Then tighten the nuts by hand as tight as you can. 2 Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner.
English – 15 C Checking chain lubrication • Check the chain lubrication each time you refuel. Aim the tip of the saw at a light coloured surface about 20 cm away. After 1 minute running at 3/4 throttle you should see a distinct line of oil on the light surface.
16 – English H Bar Check regularly: • Whether there are burrs on the edges of the bar. Remove these with a file if necessary. • Whether the groove in the bar has become badly worn. Replace the bar if necessary. • Whether the tip of the bar is uneven or badly worn.
English – 17 ! 6 Take great care when you cut with the top edge of the bar, i.e. when cutting from the underside of the object. This is known as cutting on the push stroke.
18 – English 7 FUEL SAFETY (Refuelling, fuel mixture, storage.) Fuel and fuel vapour are highly inflammable. Take care when handling fuel and chain oil. Keep away from naked flames and do not breathe in fuel vapour. • Never try to refuel the saw while it is running.
English – 19 ! SAFETY INSTRUCTIONS GENERAL WORKING INSTRUCTIONS This section describes basic safety rules for using a chain saw. This information is no substitute for professional skills and experience. If you get into a situation where you feel unsafe, stop and seek expert advice (look under FORESTRY SERVICES in the telephone directory).
20 – English ! SAFETY INSTRUCTIONS Two factors decide whether the chain will jam or the log will split. The first is how the log is supported and the second is whether it is in tension. In most cases you can avoid these problems by cutting in two stages; from the top and from the bottom of the log.
English – 21 ! SAFETY INSTRUCTIONS 2 The log is supported at one end. There is a high risk that it will split. A Start by cutting from below (about 1/3 of the way through). B Finish by cutting from above so that the two cuts meet. 3 The log is supported at both ends.
22 – English SAFETY INSTRUCTIONS FELLING CUT The felling cut is made from the opposite side of the tree and it must be perfectly horizontal. Stand on the left side of the tree and cut with the bottom edge of the bar. Make the FELLING CUT about 3-5 cm (1.
English – 23 We recommend that you use a bar that is longer than the diameter of the tree, so that you can make the FELLING CUT and DIRECTIONAL CUT with single cutting stokes. (See ”Technical data” to find out which lengths of bar are recommended for your saw).
24 – English WHA T IS WHA T? What is what? 1. Cylinder cover. 2. Front handle. 3. Front hand guard. 4. Starter cover. 5. Chain oil tank. 6. Starter handle. 7. Adjuster screw, carburetor. 8. Choke control/Start throttle lock. 9. Rear handle. 10. Stop switch.
English – 25 Mounting guide bar and chain Always wear gloves, when working with the chain, in order to protect your hands from injury. Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle. Take off the bar nuts and remove the clutch cover.
26 – English FUEL HANDLING Chain oil • The chain lubrication system is automatic. Always use special chain oil with good adhesive characteristics. • In countries where no special chain oil is available, EP 90 transmission oil can be used. • Never use waste oil.
English – 27 ! FUEL HANDLING Fuelling Taking the following precautions, will lessen the risk of fire. • Do not smoke or place warm objects in the vicinity of the fuel. • Always shut off the engine before refuelling. • Slowly open the fuel cap, when filling fuel, so that possible overpressure is slowly released.
28 – English ! Start and stop WARNING! • Never start the saw engine without the bar, chain and clutch cover (chain brake) assembled - or else the clutch can come loose and cause personal injuries. • Always move the saw away from the fueling area before starting.
English – 29 MAINTENANCE Carburetor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in.
30 – English Starter device WARNING! • When the recoil spring is assembled in the starter housing, it is in tensioned position and can when treated carelessly, pop out and cause injuries. • Always be careful, when changing the recoil spring or the starter cord.
English – 31 Muffler The muffler is designed in order to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material.
32 – English MAINTENANCE Cooling system To obtain the lowest possible running temperature the saw is equipped with a cooling system. The cooling system consists of: 1. Air intake on the starter unit. 2. Air guide plate. 3. Fan blades on the flywheel.
English – 33 Below you will find some general maintenance instructions. If you have more questions, contact your servicing dealer. Weekly maintenance 1. Check that the AV elements are not soft or torn. 2. Lubricate the clutch drum bearing. 3. File off burrs, if any, on the sides of the bar.
34 – English Engine Cylinder volume, cu.in/cm 3 Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Power, kW/ rpm Ignition system Manufacture Type of ignition system Spark plug Electrode gap, in.
English – 35 FEDERAL AND CALIFORNIA EMISSION CONTROL W ARRANTY ST A TEMENT YOUR W ARRANTY RIGHTS AND OBLIGA TIONS The EPA (The US Environmental Protection Agency), CARB (California Air Resources Boa.
1998W48 ´*3Æo¶5a¨.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Husqvarna CARB 340 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Husqvarna CARB 340 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Husqvarna CARB 340, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Husqvarna CARB 340 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Husqvarna CARB 340, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Husqvarna CARB 340.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Husqvarna CARB 340. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Husqvarna CARB 340 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.