Manuel d'utilisation / d'entretien du produit 335XPT du fabricant Husqvarna
Aller à la page of 36
101 91 92-95 Operator's manual (EP A) Read these instructions carefully and make sure you understand them before using the saw. 3 3 5X P T Califor nia.
2 – English Symbols KEY T O SYMBOLS Switch off the engine by moving the stop switch to the STOP position before carrying out any checks or maintenance. Operating position Choke Always wear approved protective gloves. Regular cleaning is required. Visual check.
English – 3 CONTENTS Contents Key to symbols ......................................................... 2 Safety instructions Personal protective equipment ................................. 4 Chain saw safety equipment ...............................
4 – English CHAIN SA W SAFETY EQUIPMENT This section explains the various safety features of the saw, how they work, and basic inspection and maintenance you should carry out to ensure safe operation. (See the ”What is what?” section to find out where these components are on Your saw).
English – 5 SAFETY INSTRUCTIONS 2 The front hand guard is not designed solely to activate the chain brake. Another important safety feature is that it prevents the chain from hitting your left hand if you lose your grip on the front handle.
6 – English 6 The way the chain brake is triggered, either manually or automatically, depends on the force of the kickback and the position of the chain saw in relation to the object that the kickback zone of the bar strikes.
English – 7 4 Vibration damping system Your chain saw is equipped with a vibration damping system that is designed to minimise vibrations in the handles and make operation easier. When you use a chain saw vibrations are generated by the uneven contact between the chain and the wood you are cutting.
8 – English SAFETY INSTRUCTIONS 3 Checking the brake trigger Place the chain saw on firm ground and start it. Make sure the chain does not touch the ground or any other object. Grasp the saw firmly, wrapping your fingers and thumbs around the handles.
English – 9 SAFETY INSTRUCTIONS 2 Throttle lock 1 Make sure the throttle control is locked at the idle setting when you release the throttle lock. 2 Press the throttle lock and make sure it returns to its original position when you release it.
10 – English 7 Muffler Never use a chain saw that has a faulty muffler. Regularly check that the muffler is securely attached to the chain saw. If the muffler on your saw is fitted with a spark arrestor mesh this must be cleaned regularly. A blocked mesh will cause the engine to overheat and may lead to serious damage.
English – 11 SAFETY INSTRUCTIONS C Some terms that describe the bar and chain When the cutting equipment supplied with your saw becomes worn or damaged you will need to replace it. Use only the type of bar and chain recommended by us. See the ”Technical data” section to find out which equipment is recommended for your saw.
12 – English SAFETY INSTRUCTIONS 2 Sharpening your chain and adjusting raker clearance The risk of kickback is increased with a badly sharpened chain! A General information on sharpening cutting teeth • Never use a blunt chain.
English – 13 C General advice on setting raker clearance • When you sharpen the cutting teeth you reduce the RAKER CLEARANCE (cutting depth). To maintain cutting performance you must file back the raker teeth to the recommended height. See the ”Technical data” section to find the raker clearance for your saw chain.
14 – English 1 Undo the bar nuts that hold the clutch cover and chain brake, using the combination spanner. Then tighten the nuts by hand as tight as you can. 2 Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner.
English – 15 C Checking chain lubrication • Check the chain lubrication each time you refuel. Aim the tip of the saw at a light coloured surface about 20 cm away. After 1 minute running at 3/4 throttle you should see a distinct line of oil on the light surface.
16 – English H Bar Check regularly: • Whether there are burrs on the edges of the bar. Remove these with a file if necessary. • Whether the groove in the bar has become badly worn. Replace the bar if necessary. • Whether the tip of the bar is uneven or badly worn.
English – 17 General rules SAFETY INSTRUCTIONS 6 Take great care when you cut with the top edge of the bar, i.e. when cutting from the underside of the object. This is known as cutting on the push stroke. The chain tries to push the saw back towards the user.
18 – English SAFETY INSTRUCTIONS GENERAL SAFETY PRECAUTIONS 1 Chain saws are designed solely for cutting wood. The only cutting equipment that can be used with this chain saw are the combinations of bars and chains recommended in the ”Technical data” section.
English – 19 SAFETY INSTRUCTIONS GENERAL WORKING INSTRUCTIONS This section describes basic safety rules for using a chain saw. This information is no substitute for professional skills and experience. If you get into a situation where you feel unsafe, stop and seek expert advice (look under FORESTRY SERVICES in the telephone directory).
20 – English SAFETY INSTRUCTIONS Two factors decide whether the chain will jam or the log will split. The first is how the log is supported and the second is whether it is in tension. In most cases you can avoid these problems by cutting in two stages; from the top and from the bottom of the log.
English – 21 SAFETY INSTRUCTIONS 2 The log is supported at one end. There is a high risk that it will split. A Start by cutting from below (about 1/3 of the way through). B Finish by cutting from above so that the two cuts meet. 3 The log is supported at both ends.
22 – English SAFETY INSTRUCTIONS FELLING CUT The felling cut is made from the opposite side of the tree and it must be perfectly horizontal. Stand on the left side of the tree and cut with the bottom edge of the bar. Make the FELLING CUT about 3-5 cm (1.
English – 23 We recommend that you use a bar that is longer than the diameter of the tree, so that you can make the FELLING CUT and DIRECTIONAL CUT with single cutting stokes. (See ”Technical data” to find out which lengths of bar are recommended for your saw).
24 – English WHA T IS WHA T? 1 24 16 5 11 7 4 2 3 8 9 10 19 6 21 20 12 18 17 13 14 15 23 26 25 27 1. Filter cover. 2. Front handle. 3. Front hand guard. 4. Starter cover 5. Chain oil tank. 6. Starter handle. 7. Adjuster screws, carburetor. 8. Stop and choke control: • Ignition on/off switch.
English – 25 Hold up the tip of the bar and tighten the chain. The chain is correctly tensioned when there is no slack on the underside of the bar, but it can still be turned easily by hand. Hold up the bar tip and tighten the bar nuts with the combination wrench.
26 – English Fuelmix Gasoline • This engine is certified to operate on unleaded gasoline. • Use good quality unleaded gasoline. • The lowest recommended octane rating is 87. If you run the engine on lower octane rating than 87 so- called “ knocking “ can occur.
English – 27 Fuelling Taking the following precautions, will lessen the risk of fire. • Do not smoke or place warm objects in the vicinity of the fuel. • Always shut off the engine before refuelling. • Slowly open the fuel cap, when filling fuel, so that possible overpressure is slowly released.
28 – English ST ART AND ST OP Start Activate the chain brake by pushing the front hand guard forwards. Grip the front handle with your right hand and hold the saw down by putting your right knee on the rear handle. Pull the starter handle with your right hand and pull out the starter cord slowly until the starter pawls engage.
English – 29 Carburetor MAINTENANCE Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in.
30 – English Starter device WARNING! • The recoil spring is in its tensioned position in its cassette in the starter device. If the spring is handled caralessly, it can pop out and cause personal injury.. • Always be careful, when changing the recoil spring or the starter cord.
English – 31 Muffler The muffler is designed in order to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material.
32 – English MAINTENANCE Adjustment of the oil pump The oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combination spanner. The saw is supplied from the factory set to 1 turn open. Turning the screw clockwise will reduce the oil flow and turning the screw anti-clockwise will increase the oil flow.
English – 33 MAINTENANCE W eekly maintenance 1. Check that the AV elements are not soft or torn. 2. Lubricate the clutch drum bearing. 3. File off burrs, if any, on the sides of the bar. 4. Clean the spark plug and check the gap. The correct gap is 0,7 mm (0,028 inch).
34 – English 335XPT 2,7/45 1,7/43 1,22/31 2 800 1,6/9 000 FHP CD NGK BPMR 7A Champion RCJ 7Y .02"/0,5 Walbro WT 459 B 0,63/0,3 3-7 0,34/0,16 Automatic 7,5/3,4 14"/34 12"-16"/30-41 11"-15"/28-38 18,3 3/8" 0,050"/1,3 6 TECHNICAL DA T A Engine Cylinder volume, cu.
English – 35 EMISSION CONTROL W ARRANTY ST A TEMENT YOUR W ARRANTY RIGHTS AND OBLIGA TIONS The EPA (The US Environmental Protection Agency) and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2000 and later small nonroad engine.
´*33=¶59¨ 2001W06.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Husqvarna 335XPT c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Husqvarna 335XPT - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Husqvarna 335XPT, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Husqvarna 335XPT va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Husqvarna 335XPT, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Husqvarna 335XPT.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Husqvarna 335XPT. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Husqvarna 335XPT ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
