Manuel d'utilisation / d'entretien du produit Canisfer Cleaner with Power Nozzle du fabricant Hoover
Aller à la page of 20
Canisfer Cleaner with Power Nozzle by Hoover.
Fill in and retain The vacuum cleaner you have just purchased is a combination cleaner. It has a motorized nozzie for carpet and floor cleaning and tools for other tasks.
When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE Warning. injury: n To reduce the risk of fire, electric shock, or . . . . . . . . . . . . . . .
Unpacking Unpack cleaner from carton and identify the parts shown. Re- move and dispose of the car& board packing. A. Canister cleaner : B. Power nozzle / C. Paper bag / D. Extension wands and hose / j The cleaner assembled will iook like the drawing below.
1. 2. 3. 4. 5. 6. 7. 8. 9. Cover: remove by lifting up top section of carrying handle and pulling forward. Carrying handle Check bag indicator: shows red when paper bag should be checked for fullness. Extension wands: use with power nozzle. If added length is desired when using cleaning tools, add one or both wands to hose.
How to assemble 1. Connect hose Insert hose end with cord into opening of cleaner, lining up largest projection on hose with largest notch of opening. Turn hose to the right to tighten. When hose is attached properly, hose cord plug will reach to receptacle on cleaner.
To attach hose to wands, rotate plastic latch ring on hand grip until slots in opening align. Push hand grip onto wand so that button projection fits into slot. Turn plastic latch ring to lock wand in place. Push plug on power nozzle cord completely into receptacle under- neath hand grip.
How to use Power nozzle The power nozzle adjusts automatically for cleaning hard surface floors and various heights of carpet. It is not recommended for very irregular surfaces such as brick, slate, and certain parquet floors unless it is unplugged from the cleaner.
Cleaning tools The cleaning tools have many uses. Select the tool best suited for the cleaning task from the descriptions below. Adjust the suction regulator to select the amount of suction appropriate for the cleaning task. 1. Crevice tool may be used for radiators, dresser drawers, spaces between kitchen equipment.
To connect and remove tools To connect tools, insert end of tool into extension wand and snap into position. To disconnect, press down on the center of the spring latch and remove tool. Tools’attach to hand grip by rotating plastic ring until slots in the opening align.
How to store Your cleaner can be stored on end as shown in the illustration. Store power nozzle with handle in upright position. The hose and extension wands can be stored disassembled from the cleaner if desired. Maintenance The following sections are concerned with proper maintenance of the cleaner.
How to replace Disconnect cleaner from electrical outlet. 1. Remove cover by lifting top section of carrying handle and pulling forward. 2. Depress latch and lift out used bag. 3. Place lower notched edge of new bag collar into grooves located inside front of cleaner.
Clearing obstructions Remove larger items from carpet and floor surfaces before vacuuming to help prevent obstructions in hose, wands or nozzle connector, and to maintain cleaning effectiveness of your cleaner.
Secondary filter How to clean Disconnect cleaner from eiectri- cai outlet. The secondary filter is located inside the cleaner behind the paper bag. To remove filter, first remove cover of cleaner, then lift out filter. Clean filter by rinsing it in water.
1 MOTOR PULLEY AGITATOR PU 2. Return nozzle to original position; and lift off nozzle cover. 3. If the belt is not broken, pull it off the motor pulley. 4. Lift up end of agitator. Remove old belt from agitator pulley and replace with new belt. 5. Stretch belt back and attach to motor pulley.
6. Position nozzle cover on front lip of nozzle base. Press cover into place. Turn nozzle over and replace screws. Agitator brush roll When to replace Disconnect cleaner from electri- cal outlet. When agitator brushes are worn, the brush roll should be replaced.
I I AGITATOR END 1 3. Pull out shaft part way, then reinsert shaft to push out opposite agitator end. 4. Remove shaft, being careful to leave washer on shaft 5. Insert into other end to push out second agitator end. 6. Discard old agitator brush roll.
Lubrication The motor is equipped with bearings, which have been lubricated for the life of the motor. The addition of lubricant could cause damage. Therefore, do not add lubricant to either motor bearing.
---...L.I*-.i^eeI - .- Service If the problem persists, check the Yellow Pages of your telephone book under “Vacuum Cleaners-Household” for your nearest Hoover Factory Service Center or Authorized Warranty Service Dealer where approved HOOVER service and genuine HOOVER replacement parts may be obtained.
0 11) HOOVER and v@ are trademarks of THE HOOVER COMPANY, NORTH CANTON, OHIO 44720 12-91 S3399 Litho USA 56513-319.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Hoover Canisfer Cleaner with Power Nozzle c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Hoover Canisfer Cleaner with Power Nozzle - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Hoover Canisfer Cleaner with Power Nozzle, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Hoover Canisfer Cleaner with Power Nozzle va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Hoover Canisfer Cleaner with Power Nozzle, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Hoover Canisfer Cleaner with Power Nozzle.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Hoover Canisfer Cleaner with Power Nozzle. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Hoover Canisfer Cleaner with Power Nozzle ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
