Manuel d'utilisation / d'entretien du produit 1902 du fabricant Honeywell
Aller à la page of 312
™ Xenon™ 1900/1902 Area-Imaging Scanner User’s Guide.
Disc laimer Honeyw ell International Inc. (“HII”) reser v es the right to mak e changes in speci- fications and other inf or mation contained in this document without prior notice, and the reader should in all cases cons ult HII to deter mine whether any such changes hav e been made .
Pr oduct Agency Compliance - Xenon 1900 USA FCC P art 15 Subpar t B Class B This de vice complies with par t 15 of th e FCC Rules. Operation is subject to the f ollowing two conditions: 1.
Canada Industry Canada ICES-003 This Class B digital apparatus complie s with Canadian ICES-003. Opera- tion is subject to the f ollowing conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may c ause undesired operation.
In order to av oid the dissemination of those substances in our en vironment and to diminish the pressure on the na tural resources , we encourage y ou to use the appropriate take-back systems f or product disposal. Those sys- tems will reuse or recycle most of th e materials of the product you are dis- posing in a sound wa y .
Russia Gost-R cer tificate South K orea This product meets K orean agency approv al. Ta i w a n If the f ollowing label is attached to y our product, the product meets T aiwan agency approv al: BSMI S.
Caution - use of controls or adjust ments or perf ormance of procedures other than those specified herein ma y result in hazardous radiation e xpo- sure.
Pr oduct Agency Compliance - Xenon 1902 and CCB01-010BT Base USA FCC P ar t 15 Subpar t C This de vice complies with par t 15 of the FCC Rules. Operation is subject to the f ollowing two conditions: 1. This device may not cause harmful interference. 2.
C-UL Statement C-UL listed: CSA C22.2 No .60950- 1-07 for I.T .E product safety . Eur ope The CE marking on the product indicates that this device is in conf or- mity with all essential requirements of the 1999/5/EC R&TTE Directive . In addition, complies to 2006/95/EC Low V oltage Directive , when shipped with recommended powe r supply .
If you need more inf or mation on the collection, reuse, and recycling sys- tems, contact y our local or re gional waste administration. Y ou ma y also contact your supplier fo r more inf or mation on the environ- mental perf or mances of this product.
Japan Complies with T echnical Regulations Conformity Cer tification of Specified Radio equipment. Ko r e a This product meets K o rean agency approval.
Radio T echnology Class II CB Scheme Cer tified to CB Scheme IEC 60950-1, Second Edition. Laser Safety Statement If the f ollowing label is attached to yo ur product, it indicates the product contains a laser engine or laser aimer : This de vice has been tested in acco rdance with and complies with IEC60825-1 ed2.
Required Safety Labels Scanner Compliance Label location Item Number, Serial Number and Revision Information location Illumination output.
CCB01-010BT Base Item Number, Serial Number and Revision Information location Compliance Label location.
i Chapter 1 - Getting Started About This Manual ............. ......................................... 1-1 Unpacking Your Device ...... ......................................... 1-1 Connecting the Device ..............................................
ii Wincor Nixdorf Beetle™ Terminal Default Settings ............. ................................... 2-9 Keyboard Country Layout .......................................... 2-10 Keyboard Style ................... ....................................
iii Charging Information ............................................. 3-5 Battery Recommendations .................................... 3-5 Proper Disposal of the Battery .............................. 3-6 Beeper and LED Sequences and Meaning ........
iv Scanner Name ..................... ...................................... 3-22 Application Work Groups ........... ................................ 3-24 Application Work Group Selection ....................... 3-25 Resetting the Factory Defaults: All Application Work Groups .
v Scanner Power Time-Out Timer ............................ 4-7 Presentation Mode ............. ......................................... 4-9 Presentation LED Behavior after Decode ............. 4-9 Presentation Sensitivity ... .......................
vi Working Orientation ........... ........................................ 4-27 Chapter 5 - Data Editing Prefix/Suffix Overview.................................................. 5-1 To Add a Prefix or Suffix : ....................................... 5-1 To Clear One or All Prefix es or Suffixes .
vii Codabar ........................... ........................................... 7-3 Codabar Concatenation ... ..................................... 7-4 Code 39 ............................... ........................................ 7-6 Code 32 Pharmaceutical (PARAF) .
viii GS1 Composite Codes .............................................. 7-45 UPC/EAN Version ............. ................................... 7-45 GS1 Emulation........................................................... 7-46 TCIF Linked Code 39 (TLC39) .
ix Chapter 10 - Utilities To Add a Test Code I.D. Prefix to All Symbologies .................. ......................................... 10-1 Show Decoder Revision ....... ..................................... 10-1 Show Scan Driver Revision .. .......
x Chapter 13 - Maintenance Repairs ...................................................................... 13-1 Maintenance .............................................................. 13-1 Cleaning the Scanner ........... ...........................
1 - 1 1 Getting Star ted About This Manual This User’ s Guide provides installati on and programming instructions f or the Xenon™ 1900 and 1902 area-imaging sc anners. Product specifications , dimensions, w arranty , and customer su ppor t information are also included.
1 - 2 Connecting the Device Connecting with USB A scanner or a cordless base can be connected to the USB por t of a com- puter . 1. Connect the appropriate interface cable to the dev ice first, then to the computer.
1 - 3 2. Make sure the cables are secured in the wireways in the bottom of the cordless base and that the base sits flat on a horizontal surface. 3. The scanner beeps. 4. Verify the scanner or cordless base operation by scanning a bar code from the Sample Symbols in the back of this manual.
1 - 4 3. Make sure the cables are secured in the wireways in the bottom of the cordless base and that the base si ts flat on a horizontal surface. 4. Turn the terminal/computer po wer back on. The scanner beeps. 5. Verify the scanner or cordless base operation by scanning a bar code from the Sample Symbols in the back of this manual.
1 - 5 Connecting with RS232 Serial P or t 1. Turn off power to the terminal/computer. 2. Connect the appropriate inte rface cable to the scanner. Note: For the scanner or cordless base to work properly, you must have the correct cable for your type of terminal/computer.
1 - 6 3. Make sure the cables are secured in the wireways in the bottom of the cordless base and that the base si ts flat on a horizontal surface. 4. Plug the serial connector into t he serial port on your computer. Tighten the two screws to secure the connector to the port.
1 - 7 2. Make sure the cables are secured in the wireways in the bottom of the cordless base and that the base sits flat on a horizontal surface. 3. Turn the terminal/computer powe r back on. The scanner beeps. 4. Verify the scanner or cordless base operation by scanning a bar code from the Sample Symbols in the back of this manual.
1 - 8 Reading T echniques The scanner has a view finder that projects a bright red aiming beam that corre- sponds to the scanner’ s hor izontal fiel d of vie w . The aiming beam should be centered ov er the bar code, but it can be positioned in any direction f or a good read.
1 - 9 Setting Custom Defaults Y ou hav e the ability to create a set of menu commands as your o wn, custom def aults. T o do so , scan the Set Custom Defaults bar code below bef ore each menu command or sequence y ou want sa ve d.
1 - 10 there are no custom defaults , it will reset the scanner to the factory default set- tings. Any settings that have not been specified thro ugh the custom defaults will be defaulted to the factory default settings.
2 - 1 2 Pr ogramming the Interface Intr oduction This chapter describes how to program y our system for the desired interf ace. Pr ogramming the Interface - Plug and Pla y Plug and Pla y bar codes provide in stant scanner set up f or commonly used interf aces.
2 - 2 RS232 Serial P or t The RS232 Interface bar code is used when conn ecting to the serial por t of a PC or terminal. The following RS232 Interface bar code also pro- grams a carriage return (CR) and a lin e feed (LF) suffix, baud rate , and data f or mat as indicated below .
2 - 3 Each bar code abov e also programs the f ollowing suffix es for each symbol- ogy: * Suffixes programmed for Code 128 with IBM 4683 Port 5B, IBM 4683 Port 9B HHBCR-1, and IBM 4683 Port 17 Interfa.
2 - 4 USB IBM SureP os Scan one of the f ollowing “Plug and Pl a y” codes to program the scanner f or an IBM SureP os (USB handheld scanner ) or IBM SureP o s (USB tabletop scanner) interf ace. Note: After scanning one of these code s, you must power cycle the cash register.
2 - 5 USB HID Scan the f ollowing code to progr a m the scanner f or USB HID bar code scanners. USB Serial Scan the f ollowing code to progr a m the scanner to emulate a regular RS232-based COM P or t. If you are us ing a Microsoft® Windows® PC , you will need to download a driver from the Hone ywell website (www.
2 - 6 A CK/NAK Mode Ve r i f o n e ® Ruby T erminal Default Settings Scan the f ollowing Plug and Pla y code to program the scanner f or a V er i- f one Ruby terminal. This bar code se ts the baud rate to 1200 bps and the data f ormat to 8 data bits, no parity bit, 1 stop bit.
2 - 7 Gilbar co ® T erminal Default Settings Scan the f ollowing Plug and Pla y co de to program the scanner f or a Gil- barco terminal. This bar code sets th e baud rate to 2400 bps and the data f ormat to 7 data bits, ev en par ity , 2 st op bits.
2 - 8 NCR Bioptic A ux P ort Configuration Scan the f ollowing Plug and Pla y co de to program the scanner for an NCR bioptic scanner auxiliar y por t configuration.
2 - 9 Wincor Nixdorf Beetle™ T erminal Default Settings Scan the f ollowing Plug and Pla y code to program the scanner f or a Wincor Nixdorf Beetle terminal.
2 - 10 Ke yboard Country La y out Scan the appropriate countr y code below to program the k eyboard lay out for your country or language. As a general rule, the f ollowing characters are sup- por ted,.
2 - 11 Ke yboard Country (continued) Bulgaria (Latin) Canada (French) Canada (Multilingual) Croatia Czech Czech (Programmers) Czech (QWERTY) Czech (QWERTZ) Bulgaria (Cyrillic) Canada (French legacy) B.
2 - 12 Ke yboard Country (continued) Finland Gaelic Germany Greek Greek (220 Latin) Greek (220) Greek (319 Latin) Greek (319) Faeroese France Estonia Greek (Latin) Greek (MS).
2 - 13 Ke yboard Country (continued) Italian (142) Hungarian (101 key) Iceland Irish Italy Japan ASCII Kazakh Kyrgyz (Cyrillic) Hebrew Hungary Greek (Polytonic) Latin America Latvia.
2 - 14 Ke yboard Country (continued) Lithuania (IBM) Malta Mongolian (Cyrillic) Norway Poland Polish (214) Polish (Programmers) Portugal Lithuania Macedonia Latvia (QWERTY) Romania Russia.
2 - 15 Ke yboard Country (continued) SCS Serbia (Latin) Slovakia Slovakia (QWERTY) Slovakia (QWERTZ) Slovenia Spain Spanish variation Russian (Typewriter) Serbia (Cyrillic) Russian (MS) Sweden Switzer.
2 - 16 Ke yboard Country (continued) Ref er to the Honeyw ell website ( www.honeywell.com/aidc) f or complete ke y- board countr y suppor t information and appl icable interf aces.
2 - 17 appropriate countr y from the inside back cov er, then the Sa ve bar code. Ke yboard Style This programs k eyboard styles, such as Caps Loc k and Shift Lock. If you ha ve used Keyboard Conversion settings, the y will override any of the f ollowing K ey- board Style settings.
2 - 18 A utocaps via NumLock bar code should be scanned in countries (e.g., Ger- many , Fr ance) where the Caps Lock k ey cannot be used to toggle Caps Lock. The NumLock option w orks similar ly to t he regular Au tocaps, b ut uses the Num- Lock k ey to retriev e the current state of the Caps Lock.
2 - 19 Contr ol Character Output This selection sends a te xt string instead of a control character . For e xample, when the control character f or a carr iage retur n is expected, the output w ould displa y [CR] instead of the ASCII code of 0D . Ref er to ASCII Conversion Chart (Code Page 1252) on page A-4.
2 - 20 Def ault = Control + ASCII Mode Off . T urbo Mode: The scanner sends characters to a term inal fa ster . If the ter mi- nal drops characters, do not use T urbo Mode. Def ault = Off Numeric Ke ypad Mode: Sends numeric characters as if entered from a numeric ke ypad.
2 - 21 A utomatic Direct Connect Mode: This selection can be used if you ha ve an IBM A T style ter minal and the sy stem is dropping characters. Def ault = Off Automatic Direct Connect Mode On * Auto.
2 - 22 RS232 Baud Rate Baud Rate sends the data from the scanner to the terminal at the specified rate. The host terminal must be set for the same baud rate as the scanner .
2 - 23 RS232 W ord Length: Data Bits, Stop Bits, and P arity Data Bits sets the word length at 7 or 8 bits of data per character . If an applica- tion requires only ASCII He x characters 0 through 7F decimal (te xt, digits, and punctuation), select 7 data bits.
2 - 24 RS232 Receiver Time-Out The unit sta ys aw ake to receiv e data until the RS232 Re ceiver Time-Out e xpires. A manual or serial trigger resets the time-out. When an RS232 receiver is sleeping, a char acter ma y be sent to wak e up the receiv er and reset the time-out.
2 - 25 RS232 Timeout When using Flow Control with Timeout, y ou must program the length of the dela y you w ant to wait f or CTS from th e host. Set the length (in millisec- onds) f or a timeout by sc.
2 - 26 the scanner waits for ACK/NAK again. T ur n on the ACK/NAK protocol b y scanning the A CK/NAK On bar code below . T o turn off the protocol, scan A CK/NAK Off . Def ault = A CK/NAK Off . Scanner to Bioptic Comm unication The f ollowing settings are used to set up communication betw een Honeyw ell scanners and bioptic scanners.
2 - 27 Scanner -Bioptic A CK/NAK Mode Bioptic A CK/Nak On must be scanned so the sc anner will wait f or an ACK or NAK from a bioptic scanner afte r each pack et is sent. The Scanner- Bioptic A CK/NAK Timeout (below) cont rols ho w long the scanner will wait fo r a r e s p o n s e.
2 - 28.
3 - 1 3 Cor dless System Operation Note: This chapter applies only to cordle ss scanning systems. It does not apply to corded scanners. How the Cor dless Charge Base/Access P oint Wo r k s A cordless charge base or an Access P oint provide the link between the cord- less scanner and the host system.
3 - 2 Linking the Scanner to an Access P oint T ur n on the computer (l aptop/desktop). Plug the interf ace cable into the Ac cess P oint first and then into the appropriate por t on the computer . The P age button lights up when the connection to the host is made.
3 - 3 been properly sent to the base or Acce ss P oint, the scanner issues an error indication. Y ou must then chec k to s ee if the scanned data was receiv ed by the host system.
3 - 4 Scanner Is Out of Range The cordless scanner is in communicat ion with its base or Access P oint, e ven when it is not tr ansmitting bar c ode data. Whene ver the scanner can’t communicate with the base or Access P oint f or a f ew seconds , it is out of range.
3 - 5 Charging Inf ormation The batter y is designed to charge wh ile the scanner is positioned in the cordless base unit. Ref er to Base/Access Point LED Sequences and Meaning , page 3-7, f or an inter pretation of the Charge Status indicators. Ref er to Charge Only Mode (page 3-11) if you nee d to charge a scanner without linking it to the base.
3 - 6 Caution: Danger of explosion if batteri es are incorrectly replaced. Dispose of used batteries accord ing to the recycle program for batteries as directed by the go verning agency for the country where the batteries are to be discarded.
3 - 7 Scanner LED Sequences and Meaning Base/Access P oint LED Sequences and Meaning The base contains a red LED and the Access P oint has a blue LED that indicate the status of the unit and veri fies its communication with the host system. The base also has a green LED that indicates scanner battery charge condition.
3 - 8 Base P ower Comm unication Indicator T o display the po wer indicator on a base or an Access P oint, scan the Base P ower Communication Indicator On bar code.
3 - 9 P aging P aging Mode By def ault, the paging button on the base or Access P oint pages the scan- ners associated with that base or Ac cess P oint. If you want the paging b ut- ton on your base or Access P oint to be disabled, scan the P aging Mode Off bar code, belo w .
3 - 10 The base can be configured to beep at a par ticular pitch when an error occurs, such as transmission prob lems to a host system. The beeper pitch codes modify the pitch (frequency) of the error tone the base emits when there is an error . Def ault = Low .
3 - 11 Scanner Address Scan the bar code below to determine the address of the scanner you are using. Base or Access P oint Address Scan the bar code below to determine th e address of the base or Access P oint you are using.
3 - 12 If you w ant to charge a scanne r and link to the base, use Charge and Link Mode . If the base is progr a mmed f or Charge Only Mode, y ou must link a scanner to it first in order to progra m it f or Charge and Link Mode. Scan the linking bar code on the base to link the scanner , then scan Charge and Link Mode .
3 - 13 bar code. Each time a scanner is placed into a base or scans an Access P oint linking bar code, the scanner becomes the linked to the base or Access point and the old scanner is unlinked. Unlinking the Scanner If a base or an Access P oint has a scann er linked to it, that scanner must be unlinked bef ore a new scanner can be lin ked.
3 - 14 code below and then set the time-out duration (from 0-30 00 seconds) b y scan- ning digits on the Programming Chart inside the back co ver , then scanning Save . Def ault = 0 sec (no alarm). Note: If you are out of range when you scan a bar code, yo u will receive an error tone even if you do not have the al arm set.
3 - 15 Flexib le P ower Management If you are e xperi encing network performanc e issues, and suspect the scanner is interf ering with other devices, y ou can tur n down the power output of the scan- ner .
3 - 16 Reset Scanner and Base/Access P oint Once the power le vel is set, y ou must scan the Reset Base bar code and wait f or the scanner to unlink and reli nk to a base or an Access P oint. Once that is done, scan the Reset Scanner bar code and wait f or the base or Access P oint to unlink and relink to the scanner .
3 - 17 Def ault = Batch Mode Off . Batch Mode Beep When using Batch Mode, scan Batch Mode Beep On to prog ram the scan- ner to click when each bar code is read to stor age.
3 - 18 RAM Storage : The scanner will not power do wn while it contains data that has not been transmitted to the base or Access P oint, ev en if it reaches a power do wn timeout. Howe ver , if the sc anner runs out of batter y power , it will power do wn and the data will be lost.
3 - 19 2. Scan the quantity 1 bar code. 3. Scan the quantity 5 bar code. 4. Scan the quantity 0 bar code. 5. Scan the quantity 0 bar code. Example: Change a quantity of 103 to 10. T o correct an incorrect quantity , scan the quantity 0 bar code to replace the incorrect digits, then scan the correct quantity bar codes .
3 - 20 Quantity Codes (continued) Batch Mode Output Or der When batch data is transmitted, select whether you w ant that data sent as FIFO (first-in first-out), or LIFO (last-in last-out). Delete Last Code If you w ant to delete the last bar co de scanned when in Batch Mode, scan Delete Last Code .
3 - 21 T ransmit Records to Host If you are operating in In ventory Batch Mode (see Inventory Batch Mode on page 3-17), you mu st scan the fo llowing bar code to transmit all the stored data to the host system.
3 - 22 T o put the scanner in multiple scanner mode, scan the bar code below . Once you scan this bar code , the scanner is unlinked from the base or Access P o int and must either be placed into the base , or you must scan the Access P oint link- ing bar code in order to relink.
3 - 23 T o rename scanners with sequential, numeric names, scan the bar codes below . Scan the Reset code after each name change and wait f or the scanner to relink to the base or Access P oint befo re scanning a bar code to rename the ne xt scanner .
3 - 24 Application W ork Groups Y our cordless system can hav e up to 7 scanners linked to one base or Access P oint. Y ou can also hav e up to 7 work groups. If y ou want to hav e all of the scanners’ settings programmed alik e, you don’t need to use more than 1 work group .
3 - 25 Application W ork Group Selection This programming selection allo ws you to assign a scanner to a work group by scanning the bar code belo w . Y o u may then prog ram the settings (e.g., beeper volume , prefix/suffix, data form atter) that your application requires.
3 - 26 T o see what the factory default settings are, ref er to the table of Menu Commands, beginning on page 11-5. The st andard product def ault settings fo r each of the commands are indica ted by an asterisk (*). Note: Scanning this bar code also caus es both the scanner and the base or Access Point to perform a reset and become unlinked.
3 - 27 with your scanner , the scanner will not reconnect to the Bluetooth de vice when it is back in r ange. If you w ant to relink to the charge base or Access P oint, refer to Override Locked Scanner , page 3-13.
3 - 28 A uto Reconnect Mode A uto Reconnect controls whether or not the scanner automatically begins the relink process when a loss of co nnection is detected. When the Au t o Reconnect On bar code is scanned, the scann er begins the relink process immediately , without user intervention.
3 - 29 Maximum Link Attempts The Maximum Link Attempts setting cont rols the number of times the scan- ner tries to form a connection with a base or an Access P oint. Duri ng the connection setup process, the scanner transmits in order to search f or and connect to a base or an Access P oint.
3 - 30 Relink Time-Out Relink Time-Out controls the idle time between relink attempts. An attempt to link a scanner to a base or an Ac cess P oint typically lasts up to 5 sec- onds.
3 - 31 A uto Reconnect Mode set to 1 Maximum Link Attempts set to 0 Relink Time-Out set to 10 Scanner P ower Time-Out Timer set to 1800 Note: See Scanner Power Time-Out Timer on page 4-7. The scanner attempts to connect to th e base or Access P oint ev er y 15 sec- onds, measured from one attempt start to the ne xt attempt star t.
3 - 32 • Scanner operation is suspended until 1) a valid escape string is received from the host system (via the base or Access Point) or 2) the scanner times out. • Once condition 1 or 2 above has been met, the scanner is ready to scan again, and the process repeats.
3 - 33 <ESC> 8 Razz or error tone to indicate a decode/communication to host was unsuccessful. Command Action.
3 - 34.
4 - 1 4 Input/Output Settings P ower Up Beeper The scanner can be programmed to beep when it’ s powered up . If you are using a cordless system, the base can al so be programmed to beep when it is powered up . Scan the Off bar code(s) if you don’t want a po wer up beep.
4 - 2 Tr i g g e r C l i c k T o hear an audible click e very time the scanner tr igger is pressed, scan the T rigger Click On bar code below . Scan the T rigger Click Off code if y ou don’t wish to hear the click. (This f eature has no effect on serial or automatic trigger- ing.
4 - 3 Beeper V olume – Good Read The beeper volume codes modify the v o lume of the beep the scanner emits on a good read. Def ault = High. Beeper Pitch – Good Read The beeper pitch codes modify the pitc h (frequency) of the beep the scan- ner emits on a good read.
4 - 4 Beeper Pitch – Err or The beeper pitch codes modify the pitc h (frequency) of th e sound the scan- ner emits when there is a bad read or error . Def ault = Razz. Beeper Duration – Good Read The beeper duration codes modify the length of the beep the scanner emits on a good read.
4 - 5 Number of Beeps – Good Read The number of beeps of a good read can be programmed from 1 - 9. The same number of beeps will be applied to the beeper a nd LED in response to a good read. F or e xample, if y ou pr ogram this option to hav e five beeps, there will be five beeps and fiv e LED flashes in response to a good read.
4 - 6 Good Read Delay This sets the minimum amount of time bef ore the scanner can read another bar code. Def ault = 0 ms (No Dela y). User -Specified Good Read Delay If you w ant to set your o wn len.
4 - 7 slightly less range than Normal mode. Enhanced mode is best used when you require a very f ast scan speed and don’t require a long working range. Def ault = Manual T rigger-Nor mal. Serial T rigger Mode Y ou can activ ate the scanner either by pres sing the trigger , or using a serial tr ig- ger command (see Trigger Commands on page 11-4).
4 - 8 If there are no trigger pulls dur ing the timer inter val, the scanner goes into power do wn mode. Whenev er the tr igger is enabled, the timer is reset. If the scanner is placed in the charge base cradle and the battery is in the process of being charged, the scanner will not go into power do wn mode.
4 - 9 Presentation Mode Presentation Mode uses ambient light to detect bar codes. The LEDs remain off until a bar code is presented to the sc anner , then the LEDs tur n on automat- ically to read the code. If the light le vel in the room is not high enough, Presen- tation Mode ma y not work properly .
4 - 10 Presentation Centering Use Presentation Centering to narrow th e scanner’ s field of view when it is in the stand to make sure the scanner reads only those bar codes intended by the user . F or instance, if multip le codes are placed closely together , Presentation Centering will insure that only the desired codes are read.
4 - 11 Scan Presentation Centering On , then scan one of the f ollowing bar codes to change the top , bottom, left, or right of the centering window . Then scan the percent you w ant to shift the centering window using digits on the inside back co ver of this manu al.
4 - 12 Y ou ma y program a Streaming Presentation Mode (Normal, Enhanced, or Mobile Phone) you wish to use f or in -stand scanning, and a Manual T r igger mode (Normal, Enhanced, or Mobile Phone) you wish to use f or out-of-stand scanning.
4 - 13 Y ou cannot take images when in St reaming Presentation Mode . T o take images, scan Image Snap and Ship (see page 4-14). Note: If you are using a cordless charge base, it must have an external power supply plugged into the aux port fo r Streaming Presentation to work properly.
4 - 14 Image Snap and Ship Image Snap and Ship tells the scanner to take a pi cture (r ather than read a bar code) when the trigger is pressed. Once the picture is snapped, it is shipped to the host system as a jpeg file by def aul t.
4 - 15 Use shor ter delays in applications wh ere repetitiv e bar code scanning is required. Reread Dela y only works when in Presentation Mode (see page 4-9).
4 - 16 Aimer Dela y The aimer dela y allows a dela y time for the operator to aim the scanner bef ore the picture is taken. Use these codes to set the time betw een when the trigger is pulled and when the picture is taken. During the dela y time, the aiming light will appear , but the LEDs won’t turn on until the delay time is o v er .
4 - 17 Aimer Mode This f eature allows y ou to tur n the ai mer on and off. When the Interlaced bar code is scanned, the aimer is inte rlaced with the illumination LEDs.
4 - 18 In the e xample below , the white box is the centering window . The centering window has been set to 20% left, 30% ri ght, 8% top , and 25% bottom. Since Bar Code 1 passes through the centering window , it will be read. Bar Code 2 does not pass through the centering window , so it will not be read.
4 - 19 Scan Centering On , then scan one of the f ollow ing bar codes to change the top , bottom, left, or r ight of the center ing window . Then scan the percent you want to shift the centering window using digits on the inside bac k cov er of this manual.
4 - 20 Scan a bar code below to enab le or disable Pref erred Symbology . Def ault = Pref erred Symbology Off . High Priority Symbology T o specify the high pr iority symbol ogy , scan the High Pr iority Symbology bar code below . On the Symbology Chart on page A-1, find the symbology you w ant to set as high pr ior ity .
4 - 21 bar code has been encountered. Scan the bar code below , then set the dela y (from 1-3,000 milliseconds) by scanning digits from the inside bac k cov er , then scanning Save . Def ault = 500 ms. Preferred Symbology Default Scan the bar code below to set all Pr ef erred Symbology entr ies to their def ault values .
4 - 22 T o Add an Output Sequence 1. Scan the Enter Sequence symbol (see Require Output Sequence , page 4-25). 2. Code I.D. On the Symbology Chart on page A-1, find th e symbology to which you want to apply the output sequence format.
4 - 23 Output Sequence Example In this e xample, y ou are scanning Co de 93, Code 128, and Code 39 bar codes, b ut you want the scanner to out put Code 39 1st, Code 128 2nd, and Code 93 3rd, as shown below . Note: Code 93 must be enabl ed to use this example.
4 - 24 SEQBLK sequence editor star t command 62 code identifier f or Code 39 0012 A - Code 39 sample length (11) plus CR suffix (1) = 12 41 star t character match f or Code 39, 41h = “A” FF term i.
4 - 25 Require Output Sequence When an output sequence is Required , all output data must conf or m to an edited sequence or the scanner will not transmit the output data to the host de vice.
4 - 26 No Read With No Read turned On , the scanner notifies you if a code cannot be read. If using an EZConfig T ool Scan Data Window (see page 10-3 ), an “NR” appears when a code cannot be read. I f N o R e a d i s t u r n e d Off , the “NR” will not appear .
4 - 27 W orking Orientation Some bar codes are direction-sensitive . For e xample, KIX codes and OCR can misread when scanned sidew ays or upside down. Use the working orientation settings if your direction-sensitiv e codes will not usually be presented upr ight to the scanner .
4 - 28.
5 - 1 5 Data Editing Prefix/Suffix Overview When a bar code is scanned, additional in fo rm ation is sent to the host computer along with the bar code data. This gr oup of bar code data and additional, user-defined data is called a “message stri ng.
5 - 2 symbology to which you want to apply the prefix or suffix. For example, for Code 128, Code ID is “j” and Hex ID is “6A”. Step 3. Scan the 2 hex digits from the Programming Chart inside the back cover of this manual or scan 9 , 9 for all symbologies.
5 - 3 Step 1. Scan the Clear One Prefix or Clear One Suffix symbol. Step 2. Determine the 2 digit Hex val ue from the Symbology Chart (included in the Symbology Chart, beginning on page A-1) for the symbology from which you want to clear the prefix or suffix.
5 - 4 Suffix Selections Function Code T ransmit When this selection is enabled and f unction codes are contained within the scanned data, the scanner transmits the func tion code to the terminal. Char ts of these function c odes are provided in Supported Interface Keys star ting on page 9-3 .
5 - 5 Inter character Dela y An intercharacter dela y of up to 500 0 milliseconds (in 5ms increments) may be placed between the transmission of each char acter of scanned data.
5 - 6 Interfunction Dela y An interfunction dela y of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each segment of the message string. Scan the Interfunction Delay bar code below , then scan the num- ber of 5ms dela ys, and the Save bar code using the Programming Chart inside the back co ver of this manual.
6 - 1 6 Data Formatting Data Format Editor Intr oduction Y ou ma y use the Data F ormat Editor to change the scanner’s output. F or exam- ple, y ou can use the Data F ormat Editor to inser t characters at cer tain points in bar code data as it is scanned.
6 - 2 you are programming. (See Primary/Alternate Data Formats on page 6-11 for further information.) Step 3. Terminal Type Refer to Terminal ID Table (page 6-4) and loca te the Terminal ID number for your PC. Scan three nu meric bar codes on the inside back cover to program the scanner for y our terminal ID (you must enter 3 digits).
6 - 3 Other Pr ogramming Selections Clear One Data Format This deletes one data format for one symbology. If you are clearing the primary format, scan 0 from the Programming Chart inside the back cover of this manual. If you are cl earing an alternate format, scan 1 , 2 , or 3 , depending on the format you are cl earing.
6 - 4 Data Format Editor Commands Send Commands Send all character s F1 Include in the output message all of the characters from the input message, starting from current cursor position, followed by an insert character. Syntax = F1xx where xx stands for the insert character’s hex value for its ASCII code.
6 - 5 ASCII code, and xx stands for the inse rt character’s hex value for its ASCII code. Ref er to the ASCII Conversion Chart (Code Page 1252), beginning on page A-4 for decimal, hex and character codes.
6 - 6 For example, B501021F inserts an “A” on a 104 key, U.S. style keyboard. B5 = the command, 01 = number of keys pressed (without the key modifier), 02 is the key modifi er for Shift Right, and 1F is the “a” key. If a lower case “a” were to be inserted, B501001F would be entered.
6 - 7 Searc h backward f or a character F9 Search the input message backward for “xx” character from the current cursor position, leaving the cursor pointing to the “xx” character. Syntax = F9xx where xx stands for the search character’s hex value for its ASCII code.
6 - 8 Miscellaneous Commands Suppress character s FB Suppress all occurrences of up to 15 different characters, starting at the current cursor position, as the curs or is advanced by other commands. When the FC command is encountere d, the suppress function is terminated.
6 - 9 Check f or non-numeric character ED Check to make sure there is a non-numeric ASCII character at the current cursor position. The format is aborted if the character is numeric. Insert a delay EF Inserts a delay of up to 49,995 mill iseconds (in multiples of 5), starting from the current cursor position.
6 - 10 Data Format Required, Keep Prefix/Suffix Scanned data is modified according to your data format, and prefixes and suffixes are transmitted. Any data that does not match your data format requirements generates an error tone and the data in that bar code is not transmitted.
6 - 11 will sound. If you wish to hear th e error tone when a non-matching bar code is f ound, scan the Data Format Non-Match Err or T one On bar code. Def ault = Data F orm at Non-Match Error T one On . Primary/Alternate Data Formats Y ou can sav e up to four data f or mats, and s witch between these f or mats.
6 - 12 F or e xample, y ou ma y hav e set your de vice to the data f ormat you sav ed as Data F orm at 3. Y ou can s witch to Data Format 1 f or a single trigger pull by scanning the Single Scan-Data Format 1 bar code below . The next bar code that is scanned uses Data F orm at 1, then rev er ts back to Data Fo r- mat 3.
7 - 1 7 Symbologies This programming section contains the f ollowing menu selections. Ref er to Chapter 11 f or settings and def aults. • All Symbologies • Interleaved 2 of 5 • Aztec Code • Ko.
7 - 2 All Symbologies If you w ant to decode all the symbologi es allowab le for y our scanner , scan the All Symbologies On code. If on the other hand, y ou want to decode only a par ticular symbology , scan All Symbologies Off follo wed b y the On symbol f or that par ticular symbology .
7 - 3 Codabar <Default All Codabar Settings> Codabar On/Off Codabar Start / Stop Characters Star t/Stop characters identify the leadi ng and trailing ends of the bar code. Y ou ma y either transmit, or not transmit Star t/Stop characters. Def ault = Don’t T ransmit .
7 - 4 When Check Character is set to V alidate, but Don’t T ransmit , the unit will only read Codabar ba r codes printed with a check char acter , but will not transmit the chec k character with the scanned data. Codabar Concatenation Codabar suppor ts symbol concatenati on.
7 - 5 Codabar Message Length Scan the bar codes below to chang e the message length. Ref er to Message Length Description (page 7-2) f or addition al info r mation.
7 - 6 Code 39 < Default All Code 39 Settings > Code 39 On/Off Code 39 Star t / Stop Characters Star t/Stop characters identify the leadin g and trailing ends of the bar code . Y ou ma y either transmit, or not tr ansmit Star t/Stop characters. Def ault = Don’t T ransmit.
7 - 7 When Check Char acter is set to V alidate and T ransmit , the scanner only reads Code 39 bar codes printed with a check character , and will transmit this character at the end of the scanned data. Def ault = No Check Char ac- ter . Code 39 Message Length Scan the bar codes below to chang e the message length.
7 - 8 acter(s), it buff ers Code 39 bar codes until it reads a Code 39 bar code that does not hav e the append tr igger . The da ta is then transmitted in the order in which the bar codes were read (FIFO). Def ault = Off . Code 32 Pharmaceutical (P ARAF) Code 32 Pharmaceutical is a form of the Code 39 symbology used by Ital- ian pharmacies.
7 - 9 Full ASCII If Full ASCII Code 39 dec oding is enabled, certai n character pairs within the bar code symbol will be inter preted as a single character . For e xample: $V will be decoded as the ASCII ch aracter SYN, and /C will be decoded as the ASCII character #.
7 - 10 and scan the value and the Sa ve bar code from the Programming Chart on the inside the back co ver of this ma nual. The data characters should then appear properly .
7 - 11 When Check Digit is set to V alidate and T ransmit , the scanner only reads Interleaved 2 of 5 bar codes printed with a check digit, and will tr ansmit this digit at the end of the scanned data. Def ault = No Check Digit. Interleaved 2 of 5 Messa g e Length Scan the bar codes below to chang e the message length.
7 - 12 NEC 2 of 5 < Default All NEC 2 of 5 Settings > NEC 2 of 5 On/Off Check Digit No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit.
7 - 13 NEC 2 of 5 Message Length Scan the bar codes below to chang e the message length. Ref er to Message Length Description (page 7-2) f or addition al info r mation. Mini- mum and Maximum lengths = 2-80. Minim um Default = 4, Maxim um Def ault = 80.
7 - 14 Code 93 < Default All Code 93 Settings > Code 93 On/Off Code 93 Message Length Scan the bar codes below to change the message length. Ref er to Message Length Description (page 7-2) f or additional inf ormation. Mini- mum and Maximum lengths = 0-80.
7 - 15 which the bar codes are read, deleting the first space from each. The scanner transmits the appended data when it reads a Code 93 bar code that star ts with a character other than a space. Def ault = Off . Code 93 Code P age Code pages define the mapping of character codes to characters .
7 - 16 Straight 2 of 5 Industrial (three-bar star t/stop) <Default All Straight 2 of 5 Industrial Settings> Straight 2 of 5 Industrial On/Off Straight 2 of 5 Industrial Message Length Scan the bar codes below to change the message length. Ref er to Message Length Description (page 7-2) f or additional inf ormation.
7 - 17 Straight 2 of 5 IA T A (tw o-bar star t/stop) <Default All Straight 2 of 5 IATA Settings> Straight 2 of 5 IA T A On/Off Straight 2 of 5 IA T A Message Length Scan the bar codes below to chang e the message length. Ref er to Message Length Description (page 7-2) f or addition al info r mation.
7 - 18 Matrix 2 of 5 <Default All Matrix 2 of 5 Settings> Matrix 2 of 5 On/Off Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Ref er to Message Length Description (page 7-2) f or additional inf ormation. Mini- mum and Maximum lengths = 1-80.
7 - 19 Code 11 <Default All Code 11 Settings> Code 11 On/Off Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 bar codes.
7 - 20 Code 11 Message Length Scan the bar codes below to change the message length. Ref er to Message Length Description (page 7-2) f or additional inf ormation.
7 - 21 that suppor ts concatenation of neighb or ing symbols, and 4) the standard la yout f or bar codes on a blood product label. Use the bar codes below to turn concatenation on or off. Def ault =Off. Code 128 Message Length Scan the bar codes below to chang e the message length.
7 - 22 Code 128 Code P age Code pages define the mapping of character codes to characters . If the data received does not displa y with the proper characters, it ma y be because the bar code being scanned wa s created using a code page that is diff erent from the one the host progra m is e xpecting.
7 - 23 GS1-128 <Default All GS1-128 Settings> GS1-128 On/Off GS1-128 Message Length Scan the bar codes below to chang e the message length. Ref er to Message Length Description (page 7-2) f or addition al info r mation. Mini- mum and Maximum lengths = 1-80.
7 - 24 Te l e p e n <Default All Telepen Settings> T elepen On/Off T elepen Output Using AIM T elepen Output, the scanner reads symbols with star t/stop pat- tern 1 and decodes them as standard full ASCII (star t/stop patter n 1).
7 - 25 T elepen Message Length Scan the bar codes below to chang e the message length. Ref er to Message Length Description (page 7-2) f or addition al info r mation.
7 - 26 UPC-A Number System The numeric system digit of a U .P .C . symbol is nor mally transmitted at the beginning of the scanned data, but the unit can be prog rammed so it will not transmit it. Def ault = On. UPC-A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-A data.
7 - 27 UPC-A Addenda Separator When this f eature is on, there is a space between the data from the bar code and the data from the addenda. When tur ned off , there is no space. Def ault = On. UPC-A/EAN-13 with Extended Coupon Code Use the f ollowing codes to enab le or disable UPC-A and EAN-13 with Extended Coupon Code.
7 - 28 Coupon GS1 DataBar Output If you scan coupons that ha ve both UPC and GS1 DataBar codes, y ou may wish to scan and output only the data from the GS1 DataBar code. Scan the GS1 Output On code below to scan and outp ut only the GS1 DataBar code data.
7 - 29 UPC-E0 Expand UPC-E Expand e xpands the UPC-E code to the 12 digit, UPC-A format. Def ault = Off . UPC-E0 Addenda Required When Required is scanned, the scanner will only read UPC-E bar codes that hav e addenda.
7 - 30 UPC-E0 Check Digit Check Digit specifies whether the chec k digit should be transmitted at the end of the scanned data or not. Def ault = On. UPC-E0 Number System The numeric system digit of a U .P .C . symbol is nor mally transmitted at the beginning of the scanned data, but the unit can be prog rammed so it will not transmit it.
7 - 31 UPC-E1 Most U .P .C. bar codes lead with the 0 number system. F or these codes, use UPC-E0 (page 7-28). If you need to read codes that lead with the 1 n umber system, use the UPC-E1 On selection.
7 - 32 EAN/JA N-13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Def ault = Off f or both 2 Digit and 5 Digit Addenda. EAN/JA N-13 Addenda Required When Required is scanned, the scanner wi ll only read EAN/JAN-13 bar codes that hav e addenda.
7 - 33 EAN/JAN-13 Ad denda Separator When this f eature is On , there is a space between the data from the bar code and the data from the addenda. When tur ned Off , there is no space. Def ault = On. Note: If you want to enable or disabl e EAN13 with Exten ded Coupon Code, refer to UPC-A/EAN-13 with Extended Coupon Code (page 7-27).
7 - 34 EAN/J AN-8 <Default All EAN/JAN-8 Settings> EAN/JA N-8 On/Off EAN/JA N-8 Check Digit This selection allows y ou to specif y whether the check digit should be transmitted at the end of the scanned data or not.
7 - 35 EAN/JAN-8 Ad denda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data. Def ault = Off f or both 2 Digit and 5 Digit Addenda. EAN/JAN-8 Ad denda Required When Required is scanned, the scanner will only read EAN/JAN-8 bar codes that hav e addenda.
7 - 36 MSI <Default All MSI Settings> MSI On/Off MSI Chec k Character Diff erent types of check char acters are used with MSI bar codes. Y ou can program the scanner to read MSI bar codes with T ype 10 check charac- ters. Def ault = V a lidate T ype 10, but Don’t T ransmit.
7 - 37 When Check Char acter is set to V alidate T ype 10/11, but Don’t T ransmit , the unit will only read MSI bar codes printed with the specified type check character(s), b ut will not transmit th e check char acter(s) with the scanned data. MSI Message Length Scan the bar codes below to chang e the message length.
7 - 38 GS1 DataBar Omnidirectional < Default All GS1 DataBar Omnidirectional Settings > GS1 DataBar Omnidirectional On/Off GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > .
7 - 39 GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > GS1 DataBar Expanded On/Off GS1 DataBar Expanded Message Length Scan the bar codes below to chang e the message length. Ref er to Message Length Description (page 7-2) f or addition al info r mation.
7 - 40 T rioptic Code Note: If you are going to scan Code 32 Pharmaceutical codes ( page 7-8 ), Trioptic Code must be off. T r ioptic Code is used for labeling magnetic stor age media.
7 - 41 Codabloc k A Message Length Scan the bar codes below to chang e the message length. Ref er to Message Length Description (page 7-2) f or addition al info r mation. Mini- mum and Maximum lengths = 1-600. Minimum Def ault = 1, Maximum Def ault = 600.
7 - 42 Codabloc k F <Default All Codablock F Settings> Codabloc k F On/Off Codabloc k F Message Length Scan the bar codes below to change the message length. Ref er to Message Length Description (page 7-2) f or additional inf ormation. Mini- mum and Maximum lengths = 1-2048.
7 - 43 PDF417 < Default All PDF417 Settings > PDF417 On/Off PDF417 Message Length Scan the bar codes below to chang e the message length. Ref er to Message Length Description (page 7-2) f or addition al info r mation. Mini- mum and Maximum lengths = 1-2750.
7 - 44 Micr oPDF417 < Default All MicroPDF417 Settings > MicroPDF417 On/Off MicroPDF417 Messa g e Length Scan the bar codes below to change the message length. Ref er to Message Length Description (page 7-2) f or additional inf ormation. Mini- mum and Maximum lengths = 1-366.
7 - 45 GS1 Composite Codes Linear codes are combined wi th a unique 2D composit e component to form a new class called GS1 Composite symb ology . GS1 Composite symbologies allow f or the co-existence of symbologies already in use.
7 - 46 GS1 Em ulation The scanner can automatically f ormat the output from any GS1 data carrier to emulate what would be encoded in an equiv alent GS1-128 or GS1 DataBar symbol. GS1 data carriers include UPC-A and UPC-E, EAN-13 and EAN-8, ITF-14, GS1-128, and GS1-128 DataBar and GS1 Composites.
7 - 47 TCIF Linked Code 39 (TLC39) This code is a composite code since it has a Code 39 linear component and a MicroPDF417 stack ed code component. All bar code readers are capable of reading the Code 39 linear component . The MicroPDF417 component can only be decoded if TLC39 On is selected.
7 - 48 QR Code Message Length Scan the bar codes below to change the message length. Ref er to Message Length Description (page 7-2) f or additional inf ormation. Mini- mum and Maximum lengths = 1-7089. Minim um Def ault = 1, Maximum Def ault = 7089. QR Code P age QR Code pages define the mapping of character codes to characters .
7 - 49 Data Matrix < Default All Data Matrix Settings > Data Matrix On/Off Data Matrix Message Length Scan the bar codes below to chang e the message length. Ref er to Message Length Description (page 7-2) f or addition al info r mation. Mini- mum and Maximum lengths = 1-3116.
7 - 50 page A-6), and scan the value and the Sa ve bar code from the Programming Chart on the inside the back co ver of this man ual. The data characters should then appear properly . Low Density Data Matrix If you are reading lo w density Data Matrix codes (codes with little informa- tion), you can scan the Lo w Density Codes On bar code below .
7 - 51 MaxiCode < Default All MaxiCode Settings > MaxiCode On/Off MaxiCode Message Length Scan the bar codes below to chang e the message length. Ref er to Message Length Description (page 7-2) f or addition al info r mation. Mini- mum and Maximum lengths = 1-150.
7 - 52 Aztec Code < Default All Aztec Code Settings > Aztec Code On/Off Aztec Code Message Length Scan the bar codes below to change the message length. Ref er to Message Length Description (page 7-2) f or additional inf ormation. Mini- mum and Maximum lengths = 1-3832.
7 - 53 ter(s), it buff ers the number of Azte c bar codes determined by information encoded in those bar codes. Once the proper number of codes is reached, the data is output in the order specified in the bar codes. Def ault = Off. Aztec Code P age Aztec Code pages define the mapping of character codes to characters .
7 - 54 Chinese Sensible (Han Xin) Code < Default All Han Xin Settings > Han Xin Code On/Off Han Xin Code Message Length Scan the bar codes below to change the message length. Ref er to Message Length Description (page 7-2) f or additional inf ormation.
7 - 55 P ostal Codes - 2D The f ollowing lists the possib le 2D pos tal codes, and 2D postal code combina- tions that are allowed. Only one 2D pos tal code selection can be activ e at a time. If y ou scan a second 2D postal code selection, the first selection is ov er- written.
7 - 56 Combination 2D P ostal Codes: Postnet with B and B’ Fields On InfoMail On Postnet On Also see Postnet Check Digit , page 7-58. Planet Code and Postnet On Postnet and Postal-4i On Postnet and .
7 - 57 Planet Code, Postal-4i, and Intelligent Mail Bar Code On Postnet, Postal-4i, and Intelligent Mail Bar Code On Planet Code, Postal-4i, and Postnet with B and B’ Fields On Planet Code, Intellig.
7 - 58 Planet Code Check Digit This selection allows y ou to specif y whether the check digit should be transmitted at the end of Planet Code data. Def ault = Don’t T ransmit. P ostnet Check Digit This selection allows y ou to specif y whether the check digit should be transmitted at the end of P ostnet data.
7 - 59 P ostal Codes - Linear The f ollowing lists linear postal codes . Any combination of linear postal code selections can be active at a time . China P ost (Hong K ong 2 of 5) <Default All Chin.
7 - 60 China P ost (Hong K ong 2 of 5) On/Off China P ost (Hong K ong 2 of 5) Message Length Scan the bar codes below to change the message length. Ref er to Message Length Description (page 7-2) f or addit ional information. Minimum and Maximum lengths = 2-80.
7 - 61 K orea P ost <Default All Korea Post Settings> Ko r e a Po s t K orea P ost Message Length Scan the bar codes below to change the message length. Ref er to Message Length Description (page 7-2) f or additional inf o rmation. Minimum and Maximum lengths = 2-80 .
7 - 62.
8 - 1 8 Imaging Commands The scanner is like a digital camer a in the wa y it captures, manipulates, and transf ers images. The follo wing commands allow y ou to alter the way the scan- ner perf or ms these functions.
8 - 2 Step 1 - T ake a Picture Using IMGSNP Image Snap - IMGSNP An image is taken whene ver the hardware button is pressed, or when the Image Snap (IMGSNP) command is processed. The image snap command has many diff erent modifiers that can be used to change the look of the im age in memor y .
8 - 3 E - Exposure Exposure is used in Manual Style only (2P), and allows y ou to set the expo- sure time. This is similar to setti ng a shutter speed on a camer a.
8 - 4 W - T arget White V alue Sets the target f or the median gra ysc ale value in the captured image . Fo r capturing close-up images of high contrast documents, a low er setting, such as 75, is recommended. Higher settings result in longer exposure times and brighter images, but if the setting is too high, the image ma y be ov erexposed.
8 - 5 Step 2 - Ship a Picture Using IMGSHP Image Ship - IMGSHP An image is taken whene ver the b utton is pressed, or when the Image Snap (IMGSNP) command is processed. The last image is alwa ys stored in memor y . Y ou can “ship” the image by using the IMGSHP command.
8 - 6 C - Compensation Flattens the image to account f or va riations in illumination across the image. 0C Compensation disabled (default) 1C Compensation enabled D - Pixel Depth Indicates the number of bits per pix el in the transmitted image (KIM or BMP fo r m a t o n l y ) .
8 - 7 E - Edge Sharpen An edge shar pen filter cleans up the edges of an image, making it look cleaner and shar per . While edge shar pening doe s make the image look cleaner , it also remov es some fine detail from the original image. The strength of the edge shar pe n filter can be entered from 1 to 24.
8 - 8 H - Histogram Stretch Increases the contrast of the transmitt ed image . Not availab le with some image f ormats. 0H No stretch (default) 1H Histogram stretch I - In ver t Image Inv er t image is used to rotate t he image around the X or Y axis.
8 - 9 IF- Noise Reduction Used to reduce the salt and pepper noise in an image. 0if No salt and pepper noise reduction (default) 1if Salt and pepper noise reduction IR - Image Rotate 0ir Image as snap.
8 - 10 J - JPEG Image Quality Sets the desired quality when the JPEG image f or mat is selected. Higher numbers result in higher q uality , but larger files . Smaller numbers result in greater amounts of lossy compression, f aster transmission times, lowe r quality , but smaller files .
8 - 11 n B The bottom edge of the shippe d image corresponds to row n - 1 of the image in memory. Range: 000 - 480. (Default = all rows) Alternately , specify the number of pixe ls to cut from the outside margin of the image; thus only the ce nter pixels are tr ansmitted.
8 - 12 1S ship every pixel (default) 2S ship every 2nd pixel, both horizontally and vertically 3S ship every 3rd pixel, both horizontally and vertically U - Document Image Filter Allows y ou to input parameters to shar pen the edges and smooth the area between the edges of te xt in an image.
8 - 13 V - Blur Image Smooths transitions by a veraging the pi x els next to the hard edges of defined lines and shaded areas in an image. 0V Don’t blur (default) 1V Blur W - Histogram Ship A histogram giv es a quick picture of the tonal range of an image, or k ey type.
8 - 14 Image Size Compatibility If you ha ve applications that e xpect an image ship to return exactly 640x480 pix els, scan the F orce VGA Resolution bar code .
8 - 15 The f ollowing IMGBO X example wa s e x ecuted and viewed using Quic kView software . This software is a vailab le at www.honeywellaidc.com . Click on Soft- ware Downloads . Select 4600r from the Products list, then select QuickVie w Software Utility .
8 - 16 This option is used to size the image horizontally . If using this option, set the resolution (R) to zero . B - Output Image Height This option is used to size the image v er tically .
8 - 17 8F BMP format H - Height of Signature Capture Area The height of the signature captur e area must be meas ured in inches divided by .01. In the e xample, the he ight of the area to be captured is 3/8 inch, resulting in a value of H = .375/0.01 = 37.
8 - 18 F or e xample, use 2500 to specify a reso lution of 2.5. Set to ze ro when using the A and B modifiers (see A - Output Image Width and B - Output Image Height on page 8-16). S - Bar Code Aspect Ratio All dimensions used in IMGBO X are m easured as multiples of the minimum element size of the bar code .
8 - 19 Y - V er tical Bar Code Offset The vertical bar code offset allows you to offset the vertical center of the signature capture area. Negative n um bers indicate that the signature cap- ture is abov e the bar code , and positive numbers indicate that the area is below the bar code.
8 - 20.
9 - 1 9 Interface K e ys Ke yboard Function Relationships The f ollowing K eyboard Function Code , He x/ASCII V alue, and Full ASCII “CTRL ”+ relationships apply to all termin als that can be used with the scanner . Ref er to page 2-19 enable Control + ASCII mode .
9 - 2 The last five char acters in the Full ASC II “CTRL ”+ column ( [ ] 6 - ), apply to US only . The f ollowing char t indicates th e equivalents of these fiv e characters f or different countries.
9 - 3 Suppor ted Interface Ke ys ASCII HEX IBM A T/XT and PS/2 Compatibles, WYSE PC/A T Supported Keys IBM XTs and Compatibles Supported Keys IBM, DDC, Memorex T elex, Harris* Supported Keys NUL 00 Re.
9 - 4 * IBM 3191/92, 3471/72, 3196/97, 3476/77, Telex (all models) ASCII HEX IBM A T/XT and PS/2 Compatibles, WYSE PC/A T Supported Keys IBM XTs and Compatibles Supported Keys IBM, DDC, Memorex T elex.
9 - 5 Suppor ted Interface Ke ys ASCII HEX IBM, Memorex T elex (102)* Supported Keys Memorex T e lex (88)** Supported Keys NUL 00 Reser ved Reser ved SOH 01 Enter Enter STX 02 F11 PF10 ETX 03 F12 PF11.
9 - 6 Suppor ted Interface Ke ys ASCII HEX Esprit 200, 400 ANSI Supported Keys Esprit 200, 400 ASCII Supported Keys Esprit 200, 400 PC Supported Keys NUL 00 Reser ved Reserved Reserved SOH 01 New Line.
9 - 7 Suppor ted Interface Ke ys ASCII HEX Apple Mac/iMac Supported Keys NUL 00 Reser ved SOH 01 Enter/Numpad Enter STX 02 CAPS ETX 03 AL T make EO T 04 AL T break ENQ 05 CNTRL make A CK 06 CNTRL brea.
9 - 8.
10 - 1 10 Utilities T o Add a T est Code I.D . Prefix to All Symbologies This selection allows y ou to tur n on transmission of a Code I.D . before the decoded symbology . (See the Symbology Chart, beginning on page A-1) fo r the single character code th at identifies each symbology .
10 - 2 Show Data Format Scan the bar code below to show current data f or mat settings. Te s t M e n u When you scan the T est Menu On code, then scan a prog ramming code in this manual, the scanner displa ys the content of a programming code.
10 - 3 Application Plug-Ins (Apps) Any apps that y ou are using can be tur n ed off or on by scanning the follo wing bar codes. Apps are stored in groups : Decoding, and F or matting. Y ou can enable and disab le these groups of apps by scanning that group’ s On or Off bar code below .
10 - 4 Scan Data Scan Data allows y ou to scan bar codes and displa y the bar code data in a window . Scan Data lets you send serial commands to the scanner and receive scanner response that can be seen in the Scan Data win- dow . The data displayed in the Scan Data windo w can either be saved in a file or printed.
10 - 5 9. If you’ve selected the defaults du ring installation, you can click on Start Menu-All Programs - Honeywell-EZConfig..
10 - 6.
11 - 1 11 Serial Pr ogramming Commands The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will pro- gram the scanner . F or complete descr iptions and examples of each serial pro- gramming command, ref er to the corres ponding programming bar code in this manual.
11 - 2 Storage A single character that specif ies the storage table to which the command is applied. An exclamation point ( ! ) performs the command’s operation on the device’s volatile menu configuration table. A period ( . ) performs the command’s operation on the device’s non-volatile menu configuration table.
11 - 3 Responses The de vice responds to serial co mmands with one of three responses: ACK Indicates a good command which has been processed. ENQ Indicates an invalid Tag or SubTag command. NAK Indicates the command was good, but the Data field entry was out of the allowable range for this Tag an d SubTag combination, e.
11 - 4 MAX60[ACK], DFT[ACK]. This response indicates that the de vice’ s Codabar Coding Enable (CBRENA) is set to 1, or on; the Star t/Stop Character (SSX) is set to 0, or Don’t T ransmit; the Che.
11 - 5 Menu Commands Selection Setting * Indicates default Serial Command # Indicates a numeric entry Pag e Product Default Settings Setting Custom Def aults Set Custom Def aults MNUCDF 1-9 Sav e Cust.
11 - 6 Plug and Pla y Codes: RS485 IBM P or t 5B Interf ace PA P P 5 B 2-2 IBM P or t 9B HHBCR-1 Interf ace P AP9B1 2-2 IBM P or t 17 Interf ace PA P P 1 7 2-2 IBM P or t 9B HHBCR-2 Interf ace P AP9B2.
11 - 7 Plug and Pla y Codes V erifone Rub y Te r m i n a l PA P R B Y 2-6 Gilbarco T er minal P APGLB 2-7 Honeyw ell Bioptic Au x Por t PA P B I O 2-7 Datalogic Magellan Bioptic A ux P or t PA P M A G.
11 - 8 Program K eyboard Countr y Czech (Programmers) KBDCTY40 2-11 Czech (QWER TY) KBDCTY39 2-11 Czech (QWER TZ) KBDCTY38 2-11 Denmark KBDCTY8 2-11 Dutch (Netherlands) KBDCTY11 2-11 Estonia KBDCTY41 .
11 - 9 Program K eyboard Countr y Latvia (QWER TY) KBDCTY43 2-14 Lithuania KBDCTY44 2-14 Lithuania (IBM) KBDCTY45 2-14 Macedonia KBDCTY34 2-14 Malta KBDCTY74 2-14 Mongolian (Cyrillic) KBDCTY86 2-14 No.
11 - 10 Program K eyboard Countr y Ukrainian KBDCTY76 2-16 United Kingdom KBDCTY7 2-16 United Stated (Dvor a k right) KBDCTY89 2-16 United States (Dvor a k left) KBDCTY88 2-16 United States (Dvor ak) .
11 - 11 K eyboard Modifiers *Control + ASCII Off KBDCAS0 2-20 DOS Mode Control + ASCII KBDCAS1 2-20 Windows Mode Control + ASCII KBDCAS2 2-20 Windows Mode Prefix/Suffix Off KBDCAS3 2-20 *T urbo Mode O.
11 - 12 W ord Length: Data Bits, Stop Bits , and Pa r i t y 7 Data, 1 Stop , P ar ity Even 232WRD3 2-23 7 Data, 1 Stop , P ar ity None 232WRD0 2-23 7 Data, 1 Stop , P ar ity Odd 232WRD6 2-23 7 Data, 2.
11 - 13 Scanner-Bioptic AC K / N A K M o d e *Bioptic A CK/NAK Off 232NAK0 2-27 Bioptic A CK/NAK On 232NAK1 2-27 Scanner-Bioptic A CK/NAK Timeout A CK/NAK Timeout *5100 232DLK##### 2-27 Cordless System Operation Note: This section applies only to cord less systems.
11 - 14 Scanner Modes Charge Only Mode BASLNK0 3-11 *Charge and Link Mode BASLNK1 3-12 Lock ed Link Mode BASCON0,DNG1 3-13 *Open Link Mode BASCON1,DNG1 3-13 Unlink Scanner BT_RMV 3-13 Override Loc ked.
11 - 15 Quantity Codes 0 BA TNUM0 3-19 *1 BA TNUM1 3-19 2 BA TNUM2 3-19 3 BA TNUM3 3-19 4 BA TNUM4 3-19 5 BA TNUM5 3-19 6 BA TNUM6 3-19 7 BA TNUM7 3-19 8 BA TNUM8 3-20 9 BA TNUM9 3-20 Batch Mode Outpu.
11 - 16 Resetting the Custom Def aults: All Application W ork Groups Custom Def ault Settings: All W ork Groups PA P D F T 3-26 Bluetooth Connection PCs/Laptops: Non-Base BT Connection BT_DNG5 3-27 BT.
11 - 17 Beeper V olume - Good Read Off BEPL VL0 4-2 Low BEPL VL1 4-3 Medium BEPL VL2 4-3 *High BEPL VL3 4-3 Beeper Pitch - Good Read (F requency) Low (1600) (min 400Hz) BEPFQ11600 4-3 *Medium 2700) BE.
11 - 18 Manual T rigger Modes *Manual T rigger - Normal P APHHF 4-7 Manual T rigger - Enhanced P APHHS 4-7 Serial T rigger Mode Read Time-Out (0 - 300,000 ms) *30,000 TRGST O#### 4-7 Scanner P ower Ti.
11 - 19 Presentation Centering Window Presentation Centering On PDCWIN1 4-11 *Presentation Centering Off PDCWIN0 4-11 Left of Presentation Centering Window (*40%) PDCLFT### 4-11 Right of Presentation .
11 - 20 Image Snap and Ship Image Snap and Ship TRGMOD6 4-14 Hands F ree Time- Out Range 0 - 300,000 ms TRGPT O###### 4-14 Reread Dela y Shor t (500 ms) DL YRRD500 4-15 *Medium (750 ms) DL YRRD750 4-1.
11 - 21 Pref erred Symbology On PRFENA1 4-20 *Off PRFENA0 4-20 High Priority Symbology PRFCOD## 4-20 Low Priority Symbology PRFBLK## 4-20 Pref erred Symbology Timeout (*500) Range 100- 3000 PRFPT O###.
11 - 22 W orking Or ientation *Upright R OT A TN0 4-27 V er tical, Bottom to T op (Rotate CCW 90°) ROT A TN 1 4-27 Upside Down RO T A TN2 4-27 V er tical, T op to Bottom (Rotate CW 90°) ROT A TN 3 4.
11 - 23 Data Formatter Selections Data F ormat Editor *Default Data F ormat (None) DFMDF3 6-1 Enter Data F ormat DFMBK3## 6-2 Clear One Data Fo r m a t DFMCL3 6-3 Clear All Data Fo r m a t s DFMCA3 6-.
11 - 24 Single Scan Data Fo rm at Change Single Scan-Primary Data Format VSAF_0 6-12 Single Scan-Data Format 1 VSAF_1 6-12 Single Scan-Data Format 2 VSAF_2 6-12 Single Scan-Data Format 3 VSAF_3 6-12 S.
11 - 25 Code 39 Star t/Stop Char . * Don’t T ransmit C39SSX0 7-6 T ransmit C39SSX1 7-6 Code 39 Check Char . * No Check Char . C39CK20 7-7 V alidate, But Don’t Tr a n s m i t C39CK21 7-7 V alidate,.
11 - 26 NEC 2 of 5 Def ault All NEC 2 of 5 Settings N25DFT 7-12 Off N25ENA0 7-12 *On N25ENA1 7-12 NEC 2 of 5 Check Digit * No Check Char . N25CK20 7-12 V alidate, But Don’t Tr a n s m i t N25CK21 7-.
11 - 27 Straight 2 of 5 IA T A *Off A25ENA0 7-17 On A25ENA1 7-17 Straight 2 of 5 IA T A Message Length Minimum (1 - 48) *4 A25MIN## 7-17 Maximum (1 - 48) *48 A25MAX## 7-17 Matrix 2 of 5 Default All Ma.
11 - 28 Code 128 Code P age Code 128 Code P age (*2) 128DCP## 7-22 GS1-128 Default All GS1-128 Settings GS1DFT 7-23 *On GS1ENA1 7-23 Off GS1ENA0 7-23 GS1-128 Message Length Minimum (1 - 80) *1 GS1MIN .
11 - 29 UPC-A Addenda Separator Off UP A ADS0 7-27 *On UP AADS1 7-27 UPC-A/EAN-13 with Extended Coupon Code *Off CPNENA0 7-27 Allow Concatenation CPNENA1 7-27 Require Concatenation CPNENA2 7-27 Coupon.
11 - 30 EAN/JAN-13 Chec k Digit Off E13CKX0 7-31 *On E13CKX1 7-31 EAN/JAN-13 2 Digit Addenda 2 Digit Addenda On E13AD21 7-32 *2 Digit Addenda Off E13AD20 7-32 5 Digit Addenda On E13AD51 7-32 *5 Digit .
11 - 31 MSI Check Char acter *V alidate T ype 10, but Don’t T ransmit MSICHK0 7-37 V alidate T ype 10 and Tr a n s m i t MSICHK1 7-37 V alidate 2 T ype 10 Chars, b ut Don’t Tr a n s m i t MSICHK2 .
11 - 32 GS1 DataBar Expanded Def ault All GS1 DataBar Expanded Settings RSEDFT 7-39 Off RSEENA0 7-39 *On RSEENA1 7-39 GS1 DataBar Expanded Msg. Length Minimum (4 - 74) *4 RSEMIN## 7-39 Maximum (4 - 74.
11 - 33 PDF417 Msg. Length Minimum (1-2750) *1 PDFMIN 7-43 Maximum (1-2750) *2750 PDFMAX 7-43 MicroPDF417 Def ault All Micro PDF417 Settings MPDDFT 7-44 On MPDENA1 7-44 *Off MPDENA0 7-44 MicroPDF417 Msg.
11 - 34 QR Code Msg. Length Minimum (1-7089) *1 QRCMIN 7-48 Maximum (1-7089) *7089 QRCMAX 7-48 QR Code P age QR Code P a ge (*3) QRCDCP## 7-48 Data Matrix Def ault All Data Matrix Settings IDMDFT 7-49 *On IDMENA1 7-49 Off IDMENA0 7-49 Data Matrix Msg.
11 - 35 Aztec Append On AZT APP1 7-53 *Off AZT APP0 7-53 Aztec Code P age Aztec Code P age (*51) AZTDCP## 7-53 Chinese Sensible (Han Xin) Code Def ault All Han Xin Code Settings HX_DFT 7-54 On HX_ENA1 7-54 *Off HX_ENA0 7-54 Chinese Sensible (Han Xin) Code Msg.
11 - 36 Combination 2D Po s t a l C o d e s Inf oMail and British Po s t O n POST AL8 7-56 Intelligent Mail Bar Code and P ostnet with B and B’ Fields On POST AL20 7-56 P ostnet and P ostal- 4i On P.
11 - 37 Combination 2D P ostal Codes (continued) Po s t n e t , Po s t a l - 4 i , and Intelligent Mail Bar Code On POST AL24 7-57 Planet, P ostal-4i, and P ostnet with B and B’ Fields On POST AL25 .
11 - 38 China P ost (Hong K ong 2 of 5) Def ault All China P ost (Hong Ko ng 2 of 5) Settings CPCDFT 7-59 *Off CPCENA0 7-60 On CPCENA1 7-60 China P ost (Hong K ong 2 of 5) Msg.
11 - 39 Imaging Default Commands Image Snap Def ault all Imaging Commands IMGDFT 8-1 Imaging Style - Decoding SNPSTY0 8-2 *Imaging Style - Photo SNPSTY1 8-2 Imaging Style - Manual SNPSTY2 8-2 Beeper O.
11 - 40 Image Ship *Infinity Filter - Off IMGINF0 8-5 Infinity Filter - On IMGINF1 8-5 *Compensation Off IMGCOR0 8-6 Compensation On IMGCOR1 8-6 *Pix el Depth - 8 bits/ pix el (gra yscale) IMGBPP8 8-6.
11 - 41 Image Ship (continued) Inv er t Image around X axis IMGNVX1 8-8 Inv er t Image around Y axis IMGNVY1 8-8 Rotate Image none IMGR OT0 8-9 Rotate Image 90° righ t IMGRO T1 8-9 Rotate Image 180°.
11 - 42 Image Ship (continued) Ship Every 2nd Pixel IMGSUB2 8-12 Ship Every 3rd Pix el IMGSUB3 8-12 *Document Image Filter Off IMGUSH0 8-12 Document Image Filter On (0-255) IMGUSH### 8-12 *Don’t Shi.
12 - 1 12 Pr oduct Specifications 1900 Scanner Pr oduct Specifications P arameter Specification Dimensions (T ypical): Height 6.3 inches (16cm) Length 4.1 inches (10.41cm) Width 2.8 inches (7.11cm) Weight 5.2 ounces (147.42g) Illumination: Scan and Aiming LEDs LED output power 617nm + 18nm .
12 - 2 1902 Scanner Pr oduct Specifications *Storage outside of this temperature r ange could be detrimental to batter y life. P arameter Specification Dimensions (T ypical): Height 6.3 inches (16 cm) Length 4.1 inches (10.41cm) Width 2.8 inches (7.11cm) Weight 7.
12 - 3 CCB01-010BT Charge Base Pr oduct Specifications P a rameter Specification Dimensions (T ypical): Height 3.2 inches (8.128cm) Length 5.19 inches (13.183cm) Width 3.98 inches (10.109cm) Weight 6.3 oz (179g) V oltage: 4.5 to 5.5 volts Current Draw: Host T erminal Port 500mA Au x Po w e r Po r t 1A Charge Time 5 hours Radio: F requency 2.
12 - 4 CCB01-010BT Charge Base Mounting 8x32 thread x .39 in. (10mm) deep 2.36 in. 59.84mm 3.35 in. 85.09mm 2.8 in. 72.1mm.
12 - 5 Standar d Cable Pinouts Ke yboard W edge 10 Pin RJ41 Modular Plug connects to the base 1 Cable shield 2C a b l e s e l e c t 3 Supply ground 4 Terminal data 5 Terminal clock 6 Keyboard clock 7 Supply power input +5V power 8 Keyboard data 9 10 Note: Pin assignments are not compatib le with Honeywell legacy products.
12 - 6 Standar d Cable Pinouts Serial Output 10 Pin RJ41 Modular Plug connects to the base 1 Cable shield 2C a b l e s e l e c t 3 Supply ground 4 Transmit data 5 Receive data - serial data to scanner 6C T S 7+ 5 V p o w e r 8R T S 9 10 Note: Pin assignments are not compatible with Honeywell legacy products.
12 - 7 Standar d Cable Pinouts RS485 Output 10 Pin RJ41 Modular Plug connects to the base 1 Cable shield 2C a b l e s e l e c t 3 Supply ground 4 Transmit data 5 Receive data - serial data to scanner 6 7+ 5 V p o w e r 8T r a n s m i t E n a b l e 9 10 Note: RS485 signal conversion is performed in the cable.
12 - 8 Standar d Cable Pinouts USB 10 Pin Modular Plug connects to the base 1 Cable shield 2 Cable select 3 Supply ground 4 5 6 7 +5V power 8 9D a t a + 10 Data - Note: Pin assignments are not compatible with Honeywell legacy products. Use of a cable with improper pin assignm ents may lead to damage to the unit.
13 - 1 13 Maintenance Repairs Repairs and/or upgrades are not to be perf or med on this product. These ser- vices are to be perf ormed only by an authorized ser v ice center (see Customer Support on page 14-1). Maintenance Y our de vice provides reliab le and effici ent operation with a minimum of care .
13 - 2 Important! The following cleaning solutions ha ve been tested to assure saf e cleaning of your scanner’ s disi nf ectant-ready housing. They are the only solutions approv ed for use with these scanners. Damage caused b y the use of cleaners other than those listed below ma y not be covered b y the warr anty .
13 - 3 Replacing an Interface Cable 1. Turn the power to the host system OFF. 2. Disconnect the scanner’s cable from the terminal or computer. 3. Locate the small hole on the back of the scanner’s handle. This is the cable release. 4. Straighten one end of a paper clip.
13 - 4 Changing a scanner Battery 1. Loosen the thumb wheel screw on the end cap by hand or use a hex wrench. 2. Remove the battery from the handle. 3. Insert replacement battery. 4. Replace end cap and screw. T roub leshooting a Xenon Scanner The scanner automatically perf or ms self-t ests whenev er you turn it on.
13 - 5 • The scanner may not be programme d for the appropriate terminal interface. For example, you scan “12345” and the host displays “@es%.” Reprogram the scanner with the corr ect Plug and Pla y bar code. See Programming the Interface beginning on page 2-1.
13 - 6 T roubleshooting a Cor dless Scanner Note: Make sure that your scanner’s battery is charged. Visit the Services and Support section of our website ( www.honeywellaidc.com ) to check for the late st software for both the scanner and the bas e or Access Point.
14 - 1 14 Customer Suppor t T echnical Assistance If you need assistance installing or trou bleshooting your device, please call your distributor or the nearest technical support office: North America/Canada Telephone: (800) 782-4263 E-mail: hsmnasupport@honeywell.
14 - 2 Online T echnical Assistance You can also access technical assistance online at www.honeywellaidc.com . Pr oduct Service and Repair Honeywell International Inc. provides service for all its products through service centers throughout the world.
14 - 3 Japan Telephone: +81-3-6730-7344 Fax: +81-3-6730-7222 E-mail: apservic e@honeywell.com Online Product Service and Repair Assistance You can also access product servic e and repair assistance online at www.honeywellaidc.com . Limited W arranty Honeyw ell Inter national Inc.
14 - 4 HA VE BEEN AD VISED OF THE POSSIBILITY OF SUCH INJURIES, LOSSES, OR D AMAGES . SOME ST A TES, PR O VINCES, OR COUNTRIES DO NO T ALLO W THE EXCLUSION OR LIMIT A TIONS OF INCIDENT AL OR CONSE- QUENTIAL D AMAGES , SO THE ABOVE LIMIT A TION OR EXCLUSION MA Y NO T APPL Y TO Y OU .
A - 1 A Reference Charts Symbology Char t Symbology AIM ID P ossible AIM ID Modifiers ( m ) Code ID (hex) All Symbologies (0x99) A ustralian P ost ]X0 A (0x41) Aztec Code ]z m 0-9, A-C z (0x7A) Britis.
A - 2 GS1 Composite ]e m 0-3 y (0x79) GS1 DataBar ]e m 0y ( 0 x 7 9 ) GS1 DataBar Limited ]e m { (0x7B) GS1 DataBar Omnidirectional ]e m y (0x79) GS1 DataBar Expanded ]e m } (0x7D) Inf oMail ]X0 , (0x.
A - 3 Note: “m” represents the AIM modifier character. Refer to International Technical Specification, Symbology Id entifiers, for AIM modifier character details. Prefix / Suffix entries for specific sym bologies override the universal (All Symbologies, 99) entry.
A - 4 ASCII Con version Chart (Code P age 1252 ) Note: This table applies to U.S. style ke yboards. Certain characters may differ depending on your Country Code/PC regional settings.
A - 5 40 28 ( 72 48 H 104 68 h 41 29 ) 73 49 I 105 69 i 42 2A * 74 4A J 106 6A j 43 2B + 75 4B K 107 6B k 44 2C , 76 4C L 108 6C l 45 2D - 77 4D M 109 6D m 46 2E .
A - 6 Code P age Mapping of Printed Bar Codes Code pages define the mapping of charac ter codes to characters . If the data received does not displa y with the pro per characters, it ma y be because t.
A - 7 one the host program is e xpecting. If this is the case, select the code page with which the bar codes were created. The data characters should then appear properly .
A - 8 Unicode Ke y Maps 6E 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 4B 50 55 4C 51 56 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 2C 1F 20 21 22 23 24 25 26 27 28 29 2B 39 2E 2F 30 31 32 33 34 35 36 37 53 4F 54 59 3A 3B 3C 3E 3F 38 40 3D 5A 5F 64 5B 60 65 5C 61 66 5D 62 67 63 68 69 6A 6C 104 Key U.
Sample Symbols UPC-A 0 123456 7890 Interleaved 2 of 5 Code 128 EAN-13 Code 39 Codabar 1234567890 Code 128 9 780330 290951 BC321 A13579B Code 93 123456-9$ Straight 2 of 5 Industrial 123456.
Sample Symbols 6543210 GS1 DataBar (01)00123456789012 PDF417 Postnet Car Registration Zip Code Data Matrix QR Code Te s t S y m b o l Numbers Matrix 2 of 5 ID-tag (UPU 4-State) J18CUSA8E6N062315014880.
Sample Symbols Aztec MaxiCode Micro PDF417 P a ckage Label T est Message T est Message.
Pr ogramming Char t 1 0 2 3 6 7 5 4 8 9.
Pr ogramming Char t Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save again.
Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 Xenon-UG Rev C 3/11.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Honeywell 1902 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Honeywell 1902 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Honeywell 1902, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Honeywell 1902 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Honeywell 1902, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Honeywell 1902.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Honeywell 1902. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Honeywell 1902 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
