Manuel d'utilisation / d'entretien du produit CSP4518 - UT74125A du fabricant Homelite
Aller à la page of 40
Y our ne w chainsa w has been engineered and manuf actured to Homelite’s high standard for dependability , ease of operation and operator saf ety . Properly cared fo r , it will giv e you y ears of r ugged, troub le-free performance. W ARNING: T o reduce the r isk of injur y , the user must read and understand the oper ator’s manual.
UK - Page 2 Q Q Q Q Q Introduction ..................................................................................................................................................................... 2 Q Q Q Q Q General Safety Rules .................
UK - Page 3 W ARNING: The warnings, labels and instructions found in this section of the operator’s manual are for your safety. Failure to follow all instructions may result in serious personal injury. Safe operation of this tool requires that you read and understand this oper ator’s manual and all labels affixed to the tool.
UK - Page 4 GENERAL SAFETY RULES Q KEEP ALL P ARTS OF YOUR BODY aw ay from the sa w chain when the engine is running. Q Q Q Q Q AL W A YS CARR Y THE CHAINSA W WITH THE ENGINE STOPPED AND THE BRAKE ENGAGED, the guide bar and sa w chain to the rear , and the silencer a wa y from your body .
UK - Page 5 W ARNING: The warnings, labels and instructions found in this section of the operator’s manual are for your safety. Failure to follow all instructions may result in serious personal injury. GENERAL PRECAUTIONS Q Q Q Q Q DO NOT CUT VINES and/or small underbrush less than 76 mm (3 in.
UK - Page 6 PULL PUSH Fig. 1 PUSH AND PULL The reaction force is always opposite to the direction the chain is moving. Thus, the oper ator must be ready to control the PULL when cutting on the bottom edge of the bar and the PUSH when cutting along the top edge.
UK - Page 7 SYMBOLS Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and more safely. SYMBOL NAME EXPLANATION Indicates danger, warning or caution.
UK - Page 8 SA VE THESE INSTRUCTIONS SYMBOLS No Smoking Do not smoke when mixing fuel or filling fuel tank. Petrol Use unleaded petrol intended for motor vehicle use with an octane rating of 87 [R + M] / 2) or higher. Oil Use 2-cycle oil for air-cooled engines.
UK - Page 9 Weight - No bar, chain, fuel or oil ............................................................................................ .................................. 4.4 kg Fuel tank capacity .................................................
UK - Page 10 STOP Fig. 2 FRONT HAND GUARD/ CHAIN BRAKE FRONT HANDLE CYLINDER COVER TRIGGER RELEASE REAR HANDLE THROTTLE TRIGGER ON/OFF SWITCH FUEL MIX CAP CHAIN OIL CAP STARTER/FAN HOUSING STARTER GRI.
UK - Page 11 WEAR HEAD PROTECTION WEAR EYE PROTECTION WEAR HEARING PROTECTION WEAR TRIM-FITTING CLOTHING. AVOID SCARVES OR OTHER LOOSE CLOTHING WHICH COULD GET CAUGHT IN THE MACHINE WEAR “NON-SLIP” GLOVES WEAR STURDY BOOTS Fig. 3 F or your saf ety , study this entire manual before oper ating the sa w .
UK - Page 12 CHAIN BRAKE Chain brakes are designed to quickly stop the chain from rotating. When the chain brake lever/hand guard is pushed towards the bar, the chain should stop immediately. A chain brake does not prevent kick-back. The chain brake should be cleaned and tested daily.
UK - Page 13 W ARNING: Always turn off engine before refuelling. Never add fuel to a machine with a running or hot engine. Move at least 9 m ( 25 ft.) from refuelling site before starting the engine. DO NOT SMOKE! Failure to heed this warning may result in possible personal injury.
UK - Page 14 STOP ADDING OIL Use HOMELITE Bar and Chain Oil. It is designed for chains and chain oilers, and is formulated to perform over a wide temperature range with no dilution required. Chainsaw should use approximately one tank of oil per tank of fuel.
UK - Page 15 STOP Fig. 14 CHOKE LEVER Fig. 15 THROTTLE TRIGGER TRIGGER RELEASE Fig. 16 Fig. 18 RUN POSITION STARTER GRIP STARTING A COLD ENGINE: 3. Move the chain brake to the BRAKE position. NOTE: Set the chain brake by pushing the chain brake lever/hand guard forward (towards the bar) to the brake position.
UK - Page 16 7. Pull ST ARTER until engine attempts to start. Slowly pull the starter gr ip out f or a short distance until you f eel the starter engage, then briskly pull str aight up . Do not pull to the end of the rope; this may damage the star ter .
UK - Page 17 PREPARING FOR CUTTING PROPER GRIP ON HANDLES Refer to “Specific Safety Rules – Safety Apparel” earlier in this manual for appropriate safety equipment. Q Q Q Q Q Wear non-slip gloves for maximum grip and protection. Q Q Q Q Q Hold the saw firmly with both hands.
UK - Page 18 STOP BASIC OPERATING/CUTTING PROCEDURES Practise cutting a few small logs using the following technique, to get the “feel” of using your saw before you begin a major sawing operation. 1. T ake the proper stance in front of the wood with the sa w idling.
UK - Page 19 STOP W ARNING: Weather conditions and altitude may affect carburation. Do not allow bystanders close to the chainsaw while adjusting the carburettor. ADJUSTING IDLING SPEED Q Q Q Q Q If the engine starts, runs, and accelerates but will not idle, turn the idling speed screw “ T ” clockwise to increase idling speed.
UK - Page 20 FELLING TREES HAZARDOUS CONDITIONS See Figure 29. OPERA TION C W ARNING: Do NOT fell trees near power lines or near buildings which could be struck by falling limbs or the tree itself.
UK - Page 21 PLANNED PATH OF SAFE RETREAT 135° FROM PLANNED LINE OF FALL PLANNED LINE OF FALL Fig. 30 RETREAT PLANNED LINE OF FALL 45° 45° 90° 135° 135° RETREAT SAFE RETREAT ZONE 90° PROPER PROCEDURE FOR TREE FELLING See Figure 30. 1. Pick your escape route (or routes in case the intended route is blocked).
UK - Page 22 3. Cut a notch about one-third the diameter of the trunk in the side of the tree. Make the notch cuts so they intersect at right angles to the line of fall. This notch should be cleaned out to leave a straight line. To keep the weight of the wood off the saw, always make the lower cut of the notch before the upper cut.
UK - Page 23 REMOVING BUTTRESS ROOTS A buttress root is a large root extending from the trunk of the tree above the ground. Remove large buttress roots before felling. Make the horizontal cut into the buttress first, f ollowed b y the ver tical cut. Remove the resulting loose section from the work area.
UK - Page 24 BUCKING LOGS UNDER STRESS Make the first bucking cut one-third of the way through the log and finish with a two-thirds cut on the opposite side. As you cut the log, it will tend to bend. The sa w may become pinched or hung in the log if you make the first cut deeper than a third of the diameter of the log.
UK - Page 25 LIMBING AND PRUNING Q Work slowly, keeping both hands on the saw with a firm grip. Maintain secure footing and balance. Q Keep the tree between you and the chain while limbing. Cut from the side of the tree opposite the branch you are cutting.
UK - Page 26 ASSEMBLING THE BAR AND CHAIN See Figures 41 through 47. DANGER: Never start the engine before installing the guide bar, chain, drive case cover and clutch drum. Without all these parts in place, the clutch may fly off or explode, exposing the user to possible serious injury.
UK - Page 27 6. Lay out the saw chain in a loop and straighten any kinks. The cutters should face in the direction of chain rotation. If they f ace backw ards, turn the loop ov er . See Figure 45 . 7. Place the chain drive links into the bar groove as shown in figure 46.
UK - Page 28 11. Replace the outer guide bar plate, ensuring that the bar pin groove is at the bottom with the upper and lower edges angled away from the guide bar. 12. Replace the clutch cover and bar mounting nuts. 13. Tighten the bar mounting nuts finger tight only.
UK - Page 29 ADJUSTING THE CHAIN TENSION W ARNING: Never touch or adjust the chain while the motor is running. The saw chain is very sharp. Always wear protective gloves when performing maintenance on the chain. 1. Stop the engine before setting the chain tension.
UK - Page 30 Fig. 55 Fig. 56 RAKER CLEARANCE INSPECT DRIVE SPROCKET CUTTING CORNER SIDE PLATE DEPTH GAUGE TOE GULLET HEEL RIVET HOLE TOP PLATE SHARPENING THE CUTTERS Be careful to file all cutters to the specified angles and to the same length, as fast cutting can only be obtained when all cutters are uniform.
UK - Page 31 Fig. 60 Fig. 61 Fig. 59 CHECK FOR WEAR OR DAMAGE LEFT-HAND CUTTERS RIGHT-HAND CUTTERS Fig. 62 CAUTION: A dull or improperly sharpened chain can cause excessive engine speed during cutting, which may result in severe engine damage. W ARNING: Improper chain sharpening increases the potential of kick-back.
UK - Page 32 TOP PLATE FILING ANGLE Q CORRECT 30° – file holders are marked with guide marks to align file properly to produce correct top plate angle.
UK - Page 33 RESTORE ORIGINAL SHAPE BY ROUNDING THE FRONT Fig. 68 LUBRICATING HOLE Fig. 67 MAINTAINING THE GUIDE BAR CAUTION: Make sure the chain has stopped before you do any work on the saw. Every week of use, reverse the guide bar on the saw to distribute the wear for maximum bar life.
UK - Page 34 STOP STOP MOUNTING THE SAFE-T-TIP® NOSE GUARD See Figure 70. 1. Mount the SAFE-T-TIP ® on the bar nose. See Figure 70. 2. Fit the locking rivet or tab in the recessed hole in the guide bar.
UK - Page 35 STOP CLEANING THE ENGINE Clean the cylinder fins and flywheel fins with compressed air or a brush periodically. Dangerous overheating of the engine may occur due to impurities on the cylinder. W ARNING Never run the saw without all the parts, including the drive case cover and starter housing, securely in place.
UK - Page 36 CLEANING THE SPARK ARRESTING SILENCER The silencer is equipped with a spark arrester screen. A faulty spark arrester screen may create a fire hazard. Through normal use the screen becomes dir ty and should be inspected weekly and cleaned as required.
UK - Page 37 Length of Bar Guide Bar Part Number Chain Part Number 305 mm (12 in.) UP08695 UP08692 356 mm (14 in.) UP08696 UP08693 406 mm (16 in.) UP08698 UP08694 PROBLEM POSSIBLE CAUSE SOLUTION Engine will not start. Make sure ignition switch is in start position (“I”).
UK - Page 38 PROBLEM POSSIBLE CAUSE SOLUTION Engine starts, runs, and accelerates but will not idle. Bar and chain running hot and smoking. Engine starts and runs, but chain is not rotating. Carburettor requires adjustment. 1. Chain oil tank empty. 2.
UK - Page 39 W ARRANTY EC DECLARATION OF CONFORMITY According to machinery directive 98/37/EC and EMC directive 89/336/EEC - We, Homelite Consumer Products Inc.
983000-210 2-03 Ryobi T echnologies GmbH Itterpark 7 D-40724 Hilden Germany T el.: +49 0)2103 / 29 58 0 F ax : +49 0)2103 / 29 58 29 info@ryobi-rtg.de Ryobi T echnologies Customer Services Anvil House T uns Lane Henley-on-Thames RG9 1SA UK Homelite / R.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Homelite CSP4518 - UT74125A c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Homelite CSP4518 - UT74125A - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Homelite CSP4518 - UT74125A, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Homelite CSP4518 - UT74125A va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Homelite CSP4518 - UT74125A, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Homelite CSP4518 - UT74125A.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Homelite CSP4518 - UT74125A. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Homelite CSP4518 - UT74125A ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
