Manuel d'utilisation / d'entretien du produit qt14 du fabricant Holman
Aller à la page of 28
2M-HG0500 Rev C 2/22/06 10 SUNNEN DRIVE, ST. LOUIS, MO/U.S.A. 63143 PHONE (314) 781-2777 FAX (314) 781-3636 A Star Manufacturing Compa ny HOLMAN CONVEYOR SANDWICH WARMER MANUAL MODEL QT14 FOR SERVICE INFORMATION U.
Common Questions, Myths, and Misconceptions of Holman Conveyor Ovens Misconception: High Voltage (208v typical) is always the same. Reality: An oven designed for 208v should operate from 208-215v. This range is typical of local power grids and daily fluctuations.
IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 1 UNCRATING AND INSPECTION Unpack unit and components from container. Remove all visible packing material, inspect unit for damage. If damage is discovered, file a claim immediately with the carrier that handled the shipment.
IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 2 5. Allow approximately 5 to 8 minutes for the twin-fan cooling system to come on. Check the air intake fan area as noted below and be sure that there is a sufficient flow of air into the control box.
IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 3 OPERATION 1. Turn Master On/Off switch to the ON position and variable speed control to fastest time setting. Allow 1 hour for complete machine warm up. 2.
IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 4 2. Remove the Crumb Trays from both sides of the oven (daily) as shown below (DO NOT CLEAN WITH CAUSTIC CLEANERS) . 3. For lightly soiled conveyor surfaces a damp cloth or scotch pad can be used without removing the conveyor belt.
IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 5 TROUBLESHOOTING GUIDE # UNIT WILL NOT HEAT, CONVEYOR BELT WILL NOT TURN. o Be sure main circuit breaker is switched to the ON position. o Check that the unit is connected to power and Master On/Off switch is O N.
IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 6 # CONVEYOR WILL NOT TURN, UNIT HEATS PROPERLY o DISCONNECT UNIT FROM POWER SOURCE o Check both fuses (replace if necessary) o Check for obstructions that may have caused a conveyor jam.
IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 7 PREVENTIVE MAINTENANCE DAILY CLEANING PROCEDURES TO KEEP YOUR HOLMAN MODEL QT14 CONVEYOR SANDWICH WARMER.
IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 8 4. Wipe exterior of unit with a damp cloth. 5. Wipe fan grills/air intakes (located on si de of t he unit) to remove an y dust build up using a damp cloth.
IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 9 WEEKLY CONVEYOR BELT CLEANING PROCEDURES TO KEEP YOUR HOLMAN MODEL QT14 CONVEYOR SANDWICH WARMER AT PEAK.
IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 10 MONTHLY CLEANING PROCEDURES Turn power off and allow cooling fans to run until the control box is cooled off. The fans are controlled by a thermostat in the control box.
IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 11 3. Clean air intake on the side of Sandwi ch Warmer by vacuuming a ny dust and d ebris built up on fan grill. 4. Return unit to counter and remove screw holdi ng power supply side pan el in place.
IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 12 LONG TERM CLEANING PR OCEDURES (every 6 months) Turn power off and allow cooling fans to run until the cont rol box is cooled off. The fans are controlled by a thermostat in the control box.
IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 13 MAINTENANCE PROCEDURES REPLACING HEATER TUBES FOR BEST TOASTING PERFORMANCE, THIS PROCEDURE SHOULD BE DONE EVERY SIX MONTHS Turn power off and allow cooling fans to r un until the control box is cooled off.
IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 14 8. Gently slide one heater tube out of hole in warmer wall. 9. Select new heater tube to be installed. To ease installati on, a short piece of tubing such as a n automotive bra ke line or sipping straws may be used.
IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 15 REPLACING FAN MOTORS Turn power off and allow cooling fans to run until the control box is cooled off. DISCONNECT UNIT FRO M POWER S UPPLY OR TURN POWER OFF AT WALL BRE AKER.
IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 16 DRIVE CHAIN DRIVE SPROCKET DRIVEN SPROCKET REPLACING BELT DRIVE MOTOR Turn power off and allow cooling fans to run until the control box is cooled off. DISCONNECT UNIT FRO M POWER S UPPLY OR TURN POWER OFF AT WALL BRE AKER.
IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 17 Note: During factory assembly, a 1/8” side-to-si de play is adjusted into the driveshaft to allow for chassis expa nsion. 1. Unit must be cool 2. Do not adjust the sprocket on the driveshaft.
Part# 2M-4497-2 10/05 RB The foregoing warranty is in lieu of any and all other warranties expressed or implied and constitutes the entire warranty. FOR ASSISTANCE Should you need any assistance regarding the Operation or Maintenance of any Star equipment; write, phone, fax or email our Service Department.
.
OPERA T I N G IN S T R UC TION S PR I OR T O O PENING: Q TURN POWE R ON T O BE G IN P REHEAT Q S ET C O N V E Y OR SPEED T O D E SI RED S E TTIN G D URING B USINES S HOURS: Q OB SE R VE BAK E ON SAN D.
P ARTS LIST February 23, 2007, Rev D IMPORT ANT : WHEN ORDERING, INCLUDE MODEL AND SERIAL NUMBER Some items are included for illustrative purposes only and in certain instances may not be available.
P ARTS LIST February 23, 2007, Rev D IMPORT ANT : WHEN ORDERING, INCLUDE MODEL AND SERIAL NUMBER Some items are included for illustrative purposes only and in certain instances may not be available.
IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 20 DETAIL OF RESISTOR/DIODE TERMI NAL BL OCK 47 OHM DIODE WIRING DIAGRAM #020514A QT14 W/ POT SPEED CONTRO.
IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 21 W IR IN G DIA G RA M #020513A Q T 1 4 W / P O T S P EED CON TROL S I N G L E P H A S E - 208/220/ 240 P.
FA N SWITCH PILOT LIGHT RESET SWITCH ON/OFF FUSE FUSE L2 L3 Gnd L1 N BOTTOM HEA TERS TOP HEA TERS WINDOW SIDE CONTROL SIDE DRIVE MOTOR: USE BLK/WHT FOR 208V USE BLK/BLU FOR 240V 250 OHM POT (P ART OF GE-135702) MODEL: QT14 380/220/60 3 phase, 15 TUBE - SERIES THIS DRA WING CONT AINS INFORMA TION CONFIDENTIAL TO ST AR MFG.
ST AR MANUF ACTURING 10 Sunnen Drive, St. Louis, MO 63143 U.S.A. (800) 807-9054 (314) 781-2777 Parts & Service (800) 807-9054 www .star-mfg.com.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Holman qt14 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Holman qt14 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Holman qt14, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Holman qt14 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Holman qt14, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Holman qt14.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Holman qt14. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Holman qt14 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.