Manuel d'utilisation / d'entretien du produit XLR-PLUS-N-AU du fabricant Heat & Glo LifeStyle
Aller à la page of 77
1 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 Model: XLR-PLUS-N-AU XLR-PLUS-PB-AU • DO NOT store or use gasoli ne or other am- mab le vap ors an d liqu ids in th e v ici nity o f t his or any other appliance. • DO NOT spray aerosols in the vicinity of this appliance while it is in operation.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 2 MODELS:XLR-PLUS-N-AU, XLR-PLUS-PB-AU ARE SAI GLOBAL APPROVED FOR NA TUR AL GAS, PROP ANE OR BUT ANE AS A BALANCEDFLUEHEA TER.
3 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: ___.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 4 Safety AlertKey: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury . • W ARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury .
5 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 = Contains updated information. F . B l o w e r ....................................... 4 5 G. Control Module Operation . . . . . . . . . . . . . . . . . . . . . . . .
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 6 AUSTRALIANW ARRANTY INFORMA TION W arranty information in the attached manual is for international markets, not Australia. For Australian warranty information, please see below .
7 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 W arranty Period Heat & Glo Manufactured Appliances and V enting Components Covered Parts Labor Gas Wood Pellet EP .
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 8 • Non Heat & Glo venting components, hearth components or other accessories used in conjunction with the appliance. • Any part of a pre-existing replace system in which an insert or a decorative gas appliance is installed.
9 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 A. ApplianceCertication C. High AltitudeInstallations NOTICE: If the heatin g value of the gas has been reduced, these rules do not apply . Check with your local gas utility or authorities having jurisdiction.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 10 Figure2.1GeneralOperatingParts B. Y ourFireplace W ARNING! DO NOT operate replace before read - ing and understanding operating instructions. Failure to operate replace according to operating instructions could cause re or injury .
1 1 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 C. ClearSpace W ARNING! DO NOT place combustible objects in front of the replace or block louvers. High temperatures may start a re. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or hearth.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 12 I. LightingInstructions(IPI) The IPI system may be operated with four C-cell batteries. When using batteries, unplug the transformer . T o prolong battery life, remove them when using the transformer .
13 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 J. ControlModuleOperation 1. The control module has an ON/OFF/REMOTE selector switch that must be set. OFF Position: Appliance will ignore all power inputs and will not respond to any commands from a wall switch or optional remote.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 14 K. AfterFireplaceisLit InitialBreak-inProcedure • The replace should be run three to four hours continuously on high. • T urn the replace off and allow it to completely cool.
15 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 GlassCleaning Frequency: Seasonally By: Homeowner T ools Needed : Protective gloves, glass cleaner , drop cloth and a stable work surface. CAUTION! Handle xed glass assembly with care.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 16 B. MaintenanceT asks-QualiedService T echnician The following tasks must be performed by a qualied ser- vice technician.
17 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 A. T ypical ApplianceSystem NOTICE: Illustrations and photos reect typical installations and are for design purposes only . Illustrations/diagrams are not drawn to scale.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 18 B. DesignandInstallationConsiderations Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside.
19 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 5 F ramingandC learances A. Selecting ApplianceLocation Whe n sel ect ing a locat ion for the appl ia nce it is impo rt ant to con sid er th e r eq uir ed cle aranc es to wa lls (s ee Figur e 5 .
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 20 B. Constructingthe ApplianceChase A chase is a vertical box-like structure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should enclosed inside the chase.
21 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 D. MantelandW allProjections W ARN IN G! Ri sk of Fi re! C om ply wi th al l mi ni mum cl ear - an ces to c omb us ti ble s as spe ci ed .
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 22 A. V entT erminationMinimumClearances H (MI N.) - M INIMUM HEIG HT FROM R OOF TO L OWE ST DIS CHA R GE O PENING VERTICAL W ALL TERMINA TION CAP HORIZONT AL OVERHANG 305 mm X ROOF PITCH IS X/ 305 mm LOWEST DISCHARGE OPENING 510 mm MIN.
23 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 Figure6.3 MinimumClearancesforT ermination NOTES: 1. All distances are measured vertically or horizontally along the wall to a point in line with the nearest part of the terminal.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 24 A. ApprovedPipe This appliance is approved for use with Hearth & Home T echnologies SLP venting systems. Refer to Section 17.B for vent component information. DO NOT mix pipe, ttings or joining methods from differ- ent manufacturers.
25 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 Figure7.3 T opV ent-HorizontalT ermination V entingwith1elbow H 1 V 1 VMinimum H 1 Maximum 90 Elbow 457 mm 305 mm (1 ft.) 914 mm (3 ft.) 457 mm (1.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 26 INST ALLED HORIZONT ALL Y H 1 H 2 V 1 Figure7.4 1. T opV ent-HorizontalT ermination - (continued) T opV ent-HorizontalT ermination V entingwith2elbows Note : Use SLP Series components only .
27 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 Figure7.5V erticalV entMaximum Note : If installing a vertical vent/termination of f the top of the appliance, the optional exhaust restrictor may be needed.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 28 Figure7.8 H 1 V 1 V 2 T opV ent-V erticalT ermination V entingwith2elbows Note : Use SLP Series components only . V 1 Minimum HMaximum V 2 V 1 +V 2 Minimum 90° Elbow 2 ft.
29 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 IN STALLED HO RI ZON T ALL Y H 1 H 2 V 1 V 2 Figure7.9 T opV ent-V erticalT ermination V entingwith3elbows Note : Use SLP Series components only .
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 30 T opV ent-V erticalT ermination V entingwith4elbows Note : Use SLP Series components only . V 1 Min. H 1 Max. V 2 Min. H 2 Max. V 3 Min.
31 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). • SLP heat shield - designed to be used on a wall 4-3/8 in. to 7-5/8 in. (1 1 1 mm to 194 mm) thick.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 32 C. InstalltheCeilingFirestop A ceiling restop MUST be used between oors and attics. • SLPpipe only - Frame opening 9 i n. x 9 i n. (2 2 9 mm x 2 29 mm) whenever the vent penetrates a ceiling/floor (see Figure 8.
33 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 D. Install AtticInsulationShield W ARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home T echnologies Inc. requires the use of an attic shield.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 34 ELBOW HEA T SHIELD SHOWN IN SHIPPING POSITION CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp.
35 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 B. SecuringandLevelingthe Appliance W ARNING! Risk of Fire! Prevent contact with: • Sagging or loose .
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 36 1 0 Install ingV entPipe( SLPP ip e ) Figure10.
37 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 C. SecureTheV entSections • V er t i ca l r un s o f pi p e mu s t be su pp o rt ed ev er y 8 f t . (2 . 4 4 m ) . • Horizontal sections must be supported every 5 ft.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 38 D. Di sa ss em bl e V en tS ec ti on s • Rota te either se ction (s ee F igure 10 .7) so the seams on both pipe s ectio ns are alig ned as show n in F igure 10.
39 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 F . InstallMetalRoofFlashing • See minimum vent heights for various pitched roofs (Figure 10.1 1) to determine the length of pipe to extend through the roof.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 40 SCREWS CAULK STORM COLLAR (1of3) Figure10.15 TERMINA TIONCAP H.
41 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 K. InstallHorizontalT erminationCap W ARNING! Risk of Fire! The telescoping ue section of the termination cap MUST be used when connecting vent. • 1-1/2 in.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 42 1 1 GasInformation A. GasPressureRequirements Pressure requirements for XLR-PLUS-AU replaces are shown in T able 1 1.
43 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 CHECK FOR GAS LEAKS Explosion Risk Fire Risk Asphyxiation Risk • Check all ttings and connections.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 44 C. Optional AccessoriesRequirements • This appliance may be used with a wall switch, wall mou nte d therm ost at and/ or a remot e contr ol, and modu le reset switch.
45 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 D.JunctionCordInformation The junction cord is instal led at the factory .
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 46 G. ControlModuleOperation 1. The control module has an ON/OFF/R EMOTE selector switch that must be set. See Figure 12.4. OFF Posit ion : Appl ia nce will igno re all power inpu ts and will not respond to any commands from a wall switch or remote.
47 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 FCCRequirements W ARNING! Risk of Fire! Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user ’ s authority to operate the equipment.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 48 5. Close the housing door . See Figure 12.8. 4. Plac e rem ote co nt rol in sid e hou sin g.
49 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 FIREPLACE ST A TUS THERMOST A T THERMOST A T DESIRED TEMP SETTING FLAME HEIGHT F AN SPEED ADJUST ABLE AUXILIARY ADJUST.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 50 AboutONMode • All functions can be accessed when the remote control is in the ON mode. • Only active functions will be displayed when the remote control is in the ON mode.
51 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 AdjustingThermostat • Press the MENU button to activate the menu. • Using the UP and DOWN arrows highlight the THERMO icon and press SELECT . • Use the UP and DOWN arrows to turn the THERMO ON or OFF , then press SELECT (the SET TEMP will start blinking).
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 52 Frequently AskedQuestions/T roubleshooting Symptom PossibleCause Corrective Action Remote control will not transmit Batteries V erify batteries are functional and installed correctly .
53 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 1 3 F inishing A. FramingandFinishingInstructions W ARN IN G! Ri sk o f Fi re ! Co mpl y wi th a ll mi nim um cle ar - an ces to com bus tib les as sp ec i ed.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 54 W ARNING! Risk of Fire! Maintainspeciedairspace clearancestocombustibles. Failure to comply with these instructions may cause a re or cause the appliance to overheat.
55 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 Note: The lower cover panel must be pushed all the way down. The outer nishing anges should line up. The replace opening must be between 15-3/4 in. (400 mm) and 16-1/8 in.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 56 B. MantelandW allProjections W ARN IN G! Ri sk o f Fi re ! Co mpl y wi th a ll mi nim um cle ar - an ces to com bus tib les as sp ec i ed.
57 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 C. FacingMaterial • Facing and/or nishing materials must not interfere with air ow through louvers, operation of louvers or doors, or access for service. • Facing and/or nishing materials must never overhang into the glass opening.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 58 Non-Combustible Finish Material 0 - 1 in. (25 mm) Thick Bottom Joint 3/4 in. (19 mm) 3 in. (76 mm) 3/4 in. (19 mm) Figure13.1 1NoncombustibleSurfaceFinishingMaterial 0-1in.
59 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 Figure13.14.DimensionsofT onicDecorativeFront. A B D C E F TONIC FRONT T able1.DimensionsofT onicDecorativeFront. A T op of decorative front to bottom of appliance.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 60 A. RemoveFixedGlass Assembly See Section 14.E. B. RemovetheShippingMaterials Remove shipping materials from inside or underneath the rebox. The standard black rock media and manual bag assembly are also shipped underneath the rebox.
61 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 Figure14.3 AirShutter G. AirShutterSetting Air shutter settings may be adjusted by a qualied install- er at the time of installation. The air shutter is set at the factory for minimum vertical vent run.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 62 A. IntelliFirePlus™IgnitionSystem Symptom PossibleCause Corrective Action 1. Pilot won’t light. The ignitor/module makes noise, but no spark. a. Incorrect wiring.
63 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 IntelliFirePlus™IgnitionSystem-(continued) Symptom PossibleCause Corrective Action 4. Pilot lights but contin- ues to spark, and main burner will not ignite.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 64 Frequently AskedQuestions/T roubleshooting Symptom PossibleCause Corrective Action Remote control will not transmit Batteries V erify batteries are functional and installed correctly .
65 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 1 6 ComponentA ccess W ARNING! Risk of Fire, Electric Shock and Burns! T urn off power to module and valve by unplugging the 6V transformer from the junction cord, before removing xed glass assembly .
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 66 Figure16.5RemoveV alvePlateScrews 3. Set the valve bracket on the front lip of the rebox bot- tom. T urn “off” the ball valve. Disconnect gas valve from the gas ex ball valve assembly at the pressure tting.
67 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 G. GasV alveReplacement Once the valve assembly has been removed, the gas valve, pilot assembly , orice ex tube, and ex ball valve can be replaced. 1. Place the valve assembly on a clean, stable surface to service or replace any components.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 68 17 ReferenceMaterials A. ApplianceDimensionDiagram Di me ns ion s ar e ac tua l ap pl ia nc e dim en si on s. U se fo r re fe re nce o nl y. F or f ram in g di me nsi on s an d cl ea ran ce s re fe r to Se ct io n 5.
69 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 B.MaintenanceT asks Inspect MaintenanceT asks Doors 1. Inspect for scratches, dents or other damage and repair as necessary . 2. V erify no obstructions to airow .
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 70 Cap Shield DRC-RADIUS 13-7/8 in. (352 mm) 9-1/2 in (241 mm) 14 in. (356 mm) COOL-ADD Cap Shield 11-5/8 in. (295 mm) 5-3/4 in. (146 mm) 7-1/8 in (181 mm) 12-1/8 (308 mm) DVP-BEK2 DVP-HPC Cap Brick Extension 13-7/8 in.
71 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 8-1/2 in. (222 mm) 6-1/2 in. (165 mm) 6-5/8 in. (168 mm) 8-3/4 in. (152 mm) 6-1/2 in (165 mm) 6-5/8 in.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 72 SLK-SNKD Snorkel T erminationCap SLP-TVHW V ertical T erminationCap SLP-CCS-BK CathedralCeiling SupportBox-Black SLP-DCF-BK CeilingFirestop Black SLP-WT -BK W allThimble-Black C.
73 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 SLP-TRAP Horizontal T ermination Cap 15-1/8 in. (384 mm) Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be used on a wall 4 in.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 74 D. ServiceParts XLR-PLUS-N-AU,XLR-PLUS-PB-AU LandscapeHeaterRated Appliance BeginningManufacturingDate:May201 1 EndingManufacturingDate:______ IMPORT ANT : THIS IS DA TED INFORMA TION.
75 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 15.1 15.2 15.3 15.4 15.5 15.6 15.7 15.8 15.9 15.10 15.1 1 15.12 15.13 15.15 15.14 15.16 15.17 ServiceParts XLR-PLUS-N-AU,XLR-PLUS-PB-AU IMPORT ANT : THIS IS DA TED INFORMA TION.
Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 76 XLR-PLUS-N-AU,XLR-PLUS-PB-AU D. ServicePartsList IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number .
77 Heat & Glo • XLR-PLUS-N-AU, XLR-PLUS-PB-AU • 2264-900 Rev . M • 7/12 Heat & Glo, a brand of Hearth & Home T echnologies Inc. 7571 215th Street West, Lakeville, MN 55044 www .heatnglo.com E. ContactInformation Please contact your Heat & Glo dealer with any questions or concerns.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Heat & Glo LifeStyle XLR-PLUS-N-AU c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Heat & Glo LifeStyle XLR-PLUS-N-AU - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Heat & Glo LifeStyle XLR-PLUS-N-AU, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Heat & Glo LifeStyle XLR-PLUS-N-AU va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Heat & Glo LifeStyle XLR-PLUS-N-AU, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Heat & Glo LifeStyle XLR-PLUS-N-AU.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Heat & Glo LifeStyle XLR-PLUS-N-AU. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Heat & Glo LifeStyle XLR-PLUS-N-AU ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
