Manuel d'utilisation / d'entretien du produit Flextight 848 du fabricant Hasselblad
Aller à la page of 30
User's Guide Flextight 848 English.
© 2004 Hasselblad A/S. All rights reserved. Flextight 848 User's Guide, Part No 70030049, revision A. The information in this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Hasselblad A/S.
Table of Contents User's Guide - Flextight 848 Table of Contents 3 English Hardware Reference - Flextight 848 5 Warnings and Restrictions 6 System Requirements 7 Front Panel 9 Back Panel & Co.
User's Guide - Flextight 848 4 English.
Hardware Reference - Flextight 848 This manual provides important information about using your Flextight 848 scanner. Topics include: • Important warnings and restrictions • System requirements .
Warnings and Restrictions • Read all of the included documentation before attempting to install and use the scanner. • Do not touch the originals and/or the original holder while scanning. • Do not start scanning or previewing until an original holder with an original has been mounted.
System Requirements Below are the basic hardware requirements for the PC or Macintosh system to which the scanner is to be connected. For information about the processor, operating system, RAM and harddisk requirements please refer to the “Software Reference” manual, that comes with the FlexColor software.
User's Guide - Flextight 848 Hardware Reference - Flextight 848 8 English.
Front Panel A Feed Table: must be in lower position for normal scanning. When scanner is not in use you can turn it to upright position flushing with the scanner front to protect it from dust etc. Adjust to horizontal position when using the 35 mm slide mount holder (see page 15).
Back Panel & Connectors A Power Cable Socket: plug the power cable into this socket. B FireWire Interface Sockets: plug a FireWire cable (max. 6 m) here and connect it to your computer. You can use the second plug to connect another device (hard disk, printer etc.
Cut-Away View A CCD Housing: this movable platform contains the light sensor and holds the optics. B Positioning Lead Screws: for positioning of the CCD housing and optics housing for the appropriate resolution and original size. C Optics Housing: focuses the image of the original on the CCD.
Setting up the Scanner Environmental Requirements Set up the scanner in a location that fulfils the following requirements: • Keep the scanner away from sources of heat, such as direct sunlight or a radiator. Warm temperatures will degrade the quality of your scans - for best results, work in a cool environment.
Installation Procedure, FireWire Interface 1. Place the scanner on a table near your computer with the front facing away from you. Make sure that the location you choose meets all environmental - and electrical requirements as described on page 11. 2.
User's Guide - Flextight 848 Hardware Reference - Flextight 848 14 Operating Instructions English A B K L C FLEXTIGHT ORIGINAL HOLDER PATENTPENDING à à à à D E G H J F Figure 4: Operating the.
Operating Instructions (See Figure 4 opposite). 1. It is assumed that the scanner and FlexColor software have been properly installed. 2. If not already done, turn the feed table (A) to normal position. 3. Press the red power button (F) on the front of the scanner to switch it on.
User's Guide - Flextight 848 Hardware Reference - Flextight 848 16 Operating Instructions English A B K L C FLEXTIGHT ORIGINAL HOLDER PATENTPENDING à à à à D E G H J F Figure 4: Operating the.
...continued NOTE! Each original holder has it's own unique identification code (a combination of small rectangular holes at the holder 's leading edge).
...continued 9. Lay the top layer of the holder down flat over the original. • For transparency holders, the top layer is magnetic, which will hold the original fast.
Resolutions True Resolutions The table below shows the max. resolutions (in ppi) available with each of the original holders when scanning in True Resolutions mode. User's Guide - Flextight 848 English Hardware Reference - Flextight 848 19 Resolutions Original Max.
Calibrating the Scanner The scanner requires two types of calibration: • Focus calibration adjusts the positioning of the scanners optics for each zoom level. If your scans are coming out unfocused or at slightly the wrong size, then you may need to make a new focus calibration to adjust the zoom mechanism.
Focus Calibration The Flextight 848 scanner uses an adjustable zoom and focus mechanism to optimize its scanning resolution for each of the original formats it can handle. If you suspect your scans are not as sharp as they should be, then you may need to calibrate your scanner.
White Calibration for Reflectives The Flextight scanner uses a white reference to make sure that all elements in the scanner's CCD react consistently to light brightnesses. The scanner has been calibrated from the factory, and the calibration data is stored in the scanner ’s flash PROM.
5. Click on Calibrate . The scanner will take several scans of the white target. The process will take about eight minutes. User's Guide - Flextight 848 English Hardware Reference - Flextight 848.
User's Guide - Flextight 848 English Hardware Reference - Flextight 848 24 The Light Tubes PRESS PULL OUT PULL OUT PRESS à A E B C G D F 1 2 Figure 7: Replacing the Light Tubes.
The Light Tubes General The Flextight 848 contains two light tubes: one for illuminating reflective originals from above, the other for shining light through transparencies from below. Replacing the Light Tubes If your scans are suddenly coming out black (or all white if you are scanning negatives), then one of your light tubes may be defective.
User's Guide - Flextight 848 English Hardware Reference - Flextight 848 26 The Light Tubes PRESS PULL OUT PULL OUT PRESS à A E B C G D F 1 2 Figure 7: Replacing the Light Tubes.
...continued 8. Remove the defective tube: • Press the flaps backwards to release the tube. • Pull the tube gently out of the holders and then sideways out of the scanner. 9. Insert the replacement tube and mount it into the holders making sure that it is properly held in place by the flaps.
Technical Specifications Power Connector: Power Consumption Max. 60 W during operation Power Requirements 100-240V AC, 1.3A, 50-60Hz Interface to Computer FireWire (IEEE 1394) Front Panel One multifunction switch (on/off switch) Status indicator LED’s Drum Force 1kg (2.
FCC Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
CE - Declaration of conformity User's Guide - Flextight 848 Hardware Reference - Flextight 848 30 CE - Declaration of conformity English HASSELBLAD A/S HEJREVEJ 30 DK - 2400 COPENHAGEN NV TELEPHONE +45 7026 0800 TELEFAX +45 7026 0900 REG./VAT NO.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Hasselblad Flextight 848 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Hasselblad Flextight 848 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Hasselblad Flextight 848, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Hasselblad Flextight 848 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Hasselblad Flextight 848, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Hasselblad Flextight 848.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Hasselblad Flextight 848. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Hasselblad Flextight 848 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
