Manuel d'utilisation / d'entretien du produit HWM8000 du fabricant Haier
Aller à la page of 18
HWM8000 Fuzzy Computerized Automatic Washing Machine User's manual This manual is for Please read this manual carefully before using. Retain it for future reference.
Contents Names of the parts Safety precautions Trouble shooting * Answer to question Packing list Specification Installation and adjustment Usage of the drain hose Preparation before washing Put in th.
Adjustable foot Front control board Front fixed foot Rear fixed foot back cover Cabinet Drain hose Back faceplate Control panel film Control panel Lint filter(Installed by user) Filter cover Level met.
Safety precautions In normal usage of the washing machine, the power plug shall be ready to be pulled or plugged with hand. Be sure to pull the plug off and close the water faucet in following cases: power failure, delivering the machine, setting the machine idle or cleaning the machine.
Do not put hand into the rotating tub. It is dangerous even if the rotation speed is slow. Take special care of the children. Keep children away from the washing machine to avoid them climbing on it. Do not decompose, repair or alter the machine by yourself.
Install the bottom plate Adjust the installation position Please install and adjust the machine according to the requirement of the manual, which is very important for you to operate the machine safely and properly. After opening the package, please lean the washing machine gently down on soft items (like towel cloth, blanket, etc.
Inner tub Lint filter After opening the package, please take out the lint filter from the document bag, install it to the filter cover of inner tub. See to the figure.
Install the water inlet pipe Connection between the water inlet hose jointer and the water faucet Water faucet, suitable water fauce t, not suitable It is required that the front end shall be longer than 10mm. The outlet end surface of the faucet shall be flat and smooth.
Dismount the water inlet hose Connection between the water inlet hose jointer and the water inlet hose Check the connection between the water inlet hose jointer and the water faucet 1.Swing the hose gently to check if it is fastened stably. 2.After installation, open the faucet to check if it leaks water.
1 Pr eparation bef or e washing Pay attention to the followings before washing Preparation before washing 1 Connect the water inlet hose. Open the water faucet. 2 Confirm that the washing machine is earthed reliably . Then plug the power plug into the receptacle.
The capacity of washing and spinning refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one cycle. Washing quantity for one cycle shall be less than the rated capacity. The thickness, size and type of the cloth will influence the actual washing capacity.
a Description of the function of the operation buttons BALANCE DISPLA Y If the bulb of the level meter is insid e the standar d circle, it indicates that the mach ine is horizon tal. CURRENT button When the washing ma chine starts running, i t will set the current automatically.
Standard Common washing Night Low noise washing during night Gentle Washing the woolen textiles or underwear FA ST 10-minute quick washing of laundries with light soil PROGRAM button The following fou.
2 Push the program button to select suitable automatic program. 3 Push the select button to select suitable procedure. After switching on the power , the washing machine will set to WASH-SPIN procedure automatically.
Times of pushing the SELECT button Push the SELECT button for 6 times, and it will resume the initial mode. It will circulate in that sequence. The SOAK procedure can work in cooperation with automatic programs like standard and night. There is intermittent pulsator stirring during soak.
5 Close the top lid. 6 Finish washing. It beeps to indicate the finishing of washing The power w ill be switched off automatically after the finishing of the washing.
There may be some water flowing out of the drain hose in the first use of the machine. It is the water remained in the machine during the ex-factory performance inspection. Phenomenon Reason How to solve It rings after starting the Reserve function. The digitron displays E0.
Packing list User's manual One piece Fuzzy computerized automatic washing machine Lint filter Name One piece Eight pieces One piece One set T apping screws Quantity Bottom plate Two pieces W ater level/Water quantity (about) Injection pressure Specification 0.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Haier HWM8000 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Haier HWM8000 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Haier HWM8000, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Haier HWM8000 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Haier HWM8000, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Haier HWM8000.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Haier HWM8000. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Haier HWM8000 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
