Manuel d'utilisation / d'entretien du produit N/A du fabricant Alvarez
Aller à la page of 15
1 S225 REPAIR MANUAL S225 REPAIR MANUAL.
2 These instructions are intended to help restore any ailing S225 Passive Loudspeaker back to factory working conditions. They show how to remove and replace the drivers. Please contact Mackie Technical Support (1-800-898-3211) to receive a Service Request Number and Order Number for parts needed for this restoration.
3 Bottom woofer replacement: 1 1 Five screws need to be removed from each side of the grill (ten screws total) using the phillips head screwdriver. A fl at head screwdriver may aid in loosening the grill if it is sticking. 8 8 1 1 2 2 3 3 4 4 5 5 6 6 7 7 9 9 10 10 2 2 Keep the ten screws in a safe place.
4 4 4 Carefully begin to remove the woofer. This woofer has a tendency to want to pop out, so please be sure to hold the woofer in place with your free hand while removing the screws with the other hand. Caution: The woofer is approximately 10 pounds with the weight unevenly distributed.
5 6 6 The picture above shows what the S225 looks like with the grill and bottom woofer removed. Place the new woofer (part #0010658) where the old one was. Follow the same steps as above, but backwards 5 to 1. Power up the S225 and the new woofer should now be pumping out glorious lows.
6 Top woofer replacement: 1 1 Five screws need to be removed from each side of the grill (ten screws total) using the phillips head screwdriver. A fl at head screwdriver may aid in loosening the grill if it is sticking. 8 8 1 1 2 2 3 3 4 4 5 5 6 6 7 7 9 9 10 10 2 2 Keep the ten screws in a safe place.
7 Top woofer replacement continued: 4 4 Carefully begin to remove the woofer. This woofer has a tendency to want to pop out, so please be sure to hold the woofer in place with your free hand while removing the screws with the other hand. Caution: The woofer is approximately 10 pounds with the weight unevenly distributed.
8 Top woofer replacement continued: 6 6 The picture above shows what the S225 looks like with the grill and top woofer removed. Place the new woofer (part #0010658) where the old one was. Follow the same steps as above, but backwards 5 to 1. Power up the S225 and the new woofer should now be pumping out glorious lows.
9 High Frequency Driver replacement: 1 1 Five screws need to be removed from each side of the grill (ten screws total) using the phillips head screwdriver. A fl at head screwdriver may aid in loosening the grill if it is sticking. 8 8 1 1 2 2 3 3 4 4 5 5 6 6 7 7 9 9 10 10 2 2 Keep the ten screws in a safe place.
10 4 4 Carefully begin to remove the entire horn assembly (with the high frequency driver still attached). A fl at head screwdriver may aid in loosening the horn assembly by prying between it and the cabinet. Hold the horn assembly in place with one hand while prying around the edge with your free hand.
11 High Frequency Driver replacement continued: 7 7 Four nuts and eight washers may be removed from the driver using the 8mm open end wrench. Turn counter- clockwise to loosen and remove, clockwise to tighten. The other three are located around the horn assembly.
12 High Frequency Driver replacement continued: 10 10 This is what the high frequency driver looks like removed from the horn assembly. Four headless screws need to be removed from the driver. Pliers could help if the screws are too tight. Turn counter- clockwise to loosen and remove, clockwise to tighten.
13 3 3 The horn assembly is shown above with the high frequency driver circled. Four screws need to be removed from the driver using the 3mm allen wrench. 4 4 Keep the four screws in a safe place. 5 5 The diaphragm and plate adapter are easily removed from the horn assembly.
14 7 7 This is what the plate adapter (left) and diaphragm (right) both look like. Place the new diaphragm (part # coming soon) where the old one was. Follow the same steps as above, but backwards 6 to 1. Power up the S225 and the new diaphragm should now be pumping out those highs again.
15 This page left blank intentionally.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Alvarez N/A c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Alvarez N/A - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Alvarez N/A, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Alvarez N/A va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Alvarez N/A, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Alvarez N/A.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Alvarez N/A. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Alvarez N/A ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
