Manuel d'utilisation / d'entretien du produit VNR 100 du fabricant Extron electronic
Aller à la page of 34
68-2237-01 Rev. A 05 13 VN-Matrix Single Channel Recorder VNR 100 User Guide VN-Matrix ®.
Safety Instructions • English W ARNING : This symbol, D , when used on the product, is intended to alert the user of the presence of uninsulated danger ous voltage within the product’ s enclosure that may pr esent a risk of electric shock.
FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC rules. The ClassA limits provide r easonable protection against harmful interfer ence when the equipment is operated in a commer cial environment.
Conventions Used in this Guide Notifications The following notifications are used in this guide: Danger: A danger indicates a situation that will result in death or sever e injury . W ARNING: A warning indicates a situation that has the potential to result in death or severe injury .
v T echnical Publications Standar ds and Styles • Introduction VNR 100 • Contents v Contents Introduction ............................................................ 1 About the Guide ................................................. 1 About the VNR 100 Recorder .
VNR 100 • Contents vi.
<Product Name> • <Section Title> 1 VNR 100 • Introduction 1 Intr oduction This section provides an overview of the user guide for the Extr on VNR100 single channel recor der and cov.
VNR 100 • Introduction 2 The VNR 100 recor der is fully compatible with existing VNM Matrix pr oducts, including the: • Extron 5-channel VN-Matrix r ecor der • Extron VN-Matrix 2 xx and 3 .
VNR 100 • Introduction 3 Overview of Recorded Str eams Encoders convert video signals to highly compressed signals that can be transferr ed over a network. • The VNR 100 recor ds the compr essed signals from the network, without further processing.
VNR 100 • Introduction 4 Multicast RTP — An Overview Multicast RTP allows a source to be displayed on multiple displays. This method uses a real-time variation of UDP (User Datagram Pr otocol) called RTP (Real-time T ransport Protocol). SOURCE DISPLA Y(S) RT P RT P RT P RT P RT P RT P Encoder sends data using RT P to a multicast group.
VNR 100 • Introduction 5 Unicast RTP — An Overview Similar to multicast RTP , this method uses a r eal-time variation of UDP protocol, called unicast RTP . This method can be used wher e the network infrastructure does not support multicast traffic.
VNR 100 • Introduction 6 Definitions PURE3 — PURE3 is specifically designed for network transmission of real time media (such as video or graphics, audio, data, and whiteboard elements). It featur es both spatial and temporal image compression, which allows for ef ficient bandwidth usage and eliminates the need for forward err or corr ection.
VNR 100 • Introduction 7 Featur es Simultaneously recor d and play back VN-Matrix A V streams — uses customer assets more ef fectively by allowing fr ee use of imaging sources independent of playb.
VNR 100 • Panels and Cabling 8 Panels and Cabling This section provides information on: • Rear Panel Features • Front Panel Cover • Front Panel Featur es Rear Panel Featur es a b ch g f e d d Figure 5.
VNR 100 • Panels and Cabling 9 Fr ont Panel Cover The front panel has a lockable cover to pr event unauthorized access to the r emovable drives. The cover has five light tubes that allow the signals from the fr ont panel LEDs to be seen when the cover is in place.
VNR 100 • Panels and Cabling 10 c USB ports (2) — used to connect a mouse and keyboard for the initial configuration. There ar e a total of four USB inputs: two r ear panel and two front panel.
VNR 100 • Configuration and Hardwar e Setup 11 Configuration and Har dwar e Setup This section provides information on how to perform the initial configuration of the VNR100 so that it will work over the Ethernet with a network that is controlled by an Enterprise Controller .
VNR 100 • Configuration and Hardwar e Setup 12 VNR 100 Power Up Pr ocedure NOTE: Before turning on the VNR 100, ensure all necessary devices ar e connected correctly and power ed up. Power up the VNR 100 by pressing the Power button ( g in figur e 8 ).
VNR 100 • Configuration and Hardwar e Setup 13 3. Click Login . The VNR 100 Recorder Settings page opens: Network settings [eth0] Recorder settings User settings Data disk IP Address Subnet Mask Gateway Serial Cont ro ller IP Cont ro ller port MTU New password Confirm New password 192.
VNR 100 • Configuration and Hardwar e Setup 14 Getting Started with the Enterprise Contr oller The VNR 100 Single channel recor der is contr olled by the VNM Enterprise Controller , which is used to configure and manage all Matrix devices in the system.
VNR 100 • Replacing the VNR 100 Drives 15 Replacing the VNR 100 Drives There ar e two optional drive r eplacement kits for the Extron VNR 100: • OS Drive Replacement Kit • Media Drive Replacement Kit The drives allow the recor der to be moved between secur e areas without compr omising confidential data.
VNR 100 • Replacing the VNR 100 Drives 16 4. Swing the lever arm out until it is perpendicular to the front of the drive caddy (as shown in the figure to the right). Use the arm to pull the caddy out of the drive bay . 5. Remove the drive. There ar e no screws to be r emoved or cable connections to be undone.
VNR 100 • Replacing the VNR 100 Drives 17 7. In the browser addr ess bar , enter the IP addr ess of the recor der followed by a colon and the port number ( 127.0.0.1:8080 ). The login page opens (see the figure to the right). 8. Enter the Username and Password .
VNR 100 • Replacing the VNR 100 Drives 18 Media Drive Replacement Kit Replacing the Media Drive 1. If necessary , switch the recor der of f by pressing and holding down the power switch ( figure 14 , a ) until the LEDs ( figur e 14 , b ) flash r ed and then go out.
VNR 100 • Replacing the VNR 100 Drives 19 3. Click Login . The VNR 100 Recorder Settings page opens (see the figure to the right). Once mounted, the capacity of the new drive will be shown under Disk free space. This takes a few seconds. 4. If you are inserting a blank drive, click Format .
VNR 100 • Reference Information 20 Refer ence Information This section provides information about: • Default Factory Settings • VN-Matrix Port Usage • Included Parts • Mounting the VNR 100 Default Factory Settings Network settings (ETH0) IP address 192.
VNR 100 • Reference Information 21 Port T ransport Usage 69 UDP TFTP Server , used for firmware upgrades 80 TCP HTTP data. V alue is user definable; the default is 80. Used to communicate between the web browser and the Enterprise Contr oller 554 TCP Real-time streaming pr otocol (RTSP) server .
VNR 100 • Reference Information 22 Included Parts Description Part Number VNR 100 Recorder 60-1291-01 Rack mounting kit VNR 100 Setup Guide Mounting the VNR 100 This section provides information on installing the VNR 100 into a rack cabinet. Rack installation requir es the use of the pr ovided rack mount kit.
VNR 100 • Reference Information 23 The supplied rack mount kit includes 2 sets of rail assemblies, 6 rail mounting brackets, and mounting screws. NOTE: The rail assemblies are specific for the left and right.
VNR 100 • Reference Information 24 Attaching the rack rails to a standard rack The rack rails come in two sections. NOTES: • The rail assemblies are specific for left and right. • The longer rail section attaches to the front of the rack. • The shorter rail section attaches to the rear of the rack.
VNR 100 • Reference Information 25 Attaching the rack rails to a T elco rack The T elco rack has one vertical post in the middle of each side. 2 2 Outer Rail Assembly Rack Mounting Rail Rail Mounting Brackets Figure 20. Attaching Rack Rails to a T elco Rack 1.
VNR 100 • Reference Information 26 Installing the VNR 100 into the rack By now , you must have the rails attached to both the VNR 100 chassis and to the rack. A TTENTION: Do not pick up the VNR 100 by the front handles. These are designed only for pulling the recor der fr om the rack.
VNR 100 • Reference Information 27 Finished Installation: Installed Figure 22. Standar d Rack Mount Installed Figure 23. T elco Rack Mount.
Extron Headquarters +1.800.633.9876 (Inside USA/Canada Only) Extron USA - W est Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 F AX +1.919.850.1001 F AX Extron Europe +800.3987.6673 (Inside Europe Only) +31.33.453.4040 +31.33.453.4050 F AX Extron Asia +65.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Extron electronic VNR 100 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Extron electronic VNR 100 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Extron electronic VNR 100, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Extron electronic VNR 100 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Extron electronic VNR 100, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Extron electronic VNR 100.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Extron electronic VNR 100. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Extron electronic VNR 100 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.