Manuel d'utilisation / d'entretien du produit 1500 du fabricant Epson
Aller à la page of 18
EPSON ® 1000/1500 Setup Guide.
Contents Setup 1 Unpacking ............................. 1 2 Installing the imaging cartridge ................. 1 3 Loading paper ........................... 4 4 Attaching the power cord ..................... 5 5 Test printing ........................
This booklet is to help you set up your printer and begin printing quickly. It also gives you instructions for routine maintenance. If you need detailed information on printer use or if you have problems printing, see your Reference Guide. Epson is a registered trademark of Seiko Epson Corporation.
Setup 1 Unpacking 1. Remove the accessories and printer from the shipping carton. 2. Set the printer on a flat, stable surface. 3. Take the packaging off the printer and the other items and store it for future use. Note: The printer weighs about 10 kg (22 lbs) and should be lifted with care.
2. While holding the imaging cartridge horizontally, gently shake it a few times to distribute the toner evenly. 3. Set the imaging cartridge on a clean, flat surface. Firmly grip the tab on the left side of the imaging cartridge. Pull the clear seal all the way out with firm, even pressure as shown.
4. Insert the imaging cartridge into the printer by placing the pins on each side of the cartridge into the grooves inside the printer. Slide it gently into the opening until it stops. 5. Gently press down on the printer cover until it clicks shut. CAUTION: Never transport the printer with the imaging cartridge installed.
3 Loading paper 1. 2. 3. 4. 5. Fan a stack of letter-size paper and even up the edges. Open the paper cover located on the top front of the printer. Adjust the paper guides inside the paper bin to match the size of the paper. Load a stack of paper (up to 150 sheets) into the paper bin.
4 Attaching the power cord 1. Make sure the power switch at the top right of the printer is turned off. 2. Insert the power cord into the back of the printer. Then plug the other end into a properly grounded outlet. 5 Test printing 1. 2. 3. 4. 5. Make sure the imaging cartridge is installed.
6 Connecting the printer to the computer You can connect up to three computers (two for the ActionLaser 1000) to your printer at the same time. If you are connecting more than one computer, see “Sharing Your Printer” in the Reference Guide.
Note: If you connect your printer to a serial or optional interface, you my need to change some of the printer’s settings. See the SelecType INTERFACE option in Chapter 4 of the Reference Guide.
8 Setting up your software Choosing the printer emulation Your printer has several resident printer emulations: HP LaserJet III (3/P/Si), Epson LQ, Epson FX, and Epson GL/2 for the ActionLaser 1500; HP LaserJet IIP (LJ-2P), Epson LQ, and Epson FX for the ActionLaser 1000.
If none of the above printers is listed, select any printer model that uses the HP Printer Command Language (PCL). For the GL/2 emulation on the ActionLaser 1500, you can print graphic data using the HP GL/2 commands or some HP GL commands. See Appendix B in the Reference Guide.
10 setup.
Maintenance Replacing the Imaging cartridge The imaging cartridge prints up to 6,000 pages depending upon the complexity of your print jobs. If your printed images become faint, enter the SelecType Level 2 TONER option to find out approximately how much toner remains in the imaging cartridge.
2. Gently open the printer cover and remove the imaging cartridge by pulling it toward you. 3. Dispose of the imaging cartridge with nonburnable items. e CAUTION: Do not turn the imaging cartridge upside down. Do not expose the imaging cartridge to light any longer than necessary.
5. Set the imaging cartridge on a clean, flat surface. Firmly grip the tab on the left side of the imaging cartridge. Pull the clear seal all the way out with firm, even pressure as shown. 6. Insert the imaging cartridge into the printer by placing the pins on each side of the cartridge into the grooves inside the printer.
7. Next you reset the TONER setting. Three messages flash in rotation on the display: NEW CARTRIDGE? YES, PRESS RESET NO, PRESS CONTINUE. 8. Press RESET to change the TONER setting to full. 9. Gently press down on the printer cover until it clicks shut.
Feed or paper jam When the printer stops printing and the FE E D JAY or PAPER JAM message appears, follow these steps: 1. Open the paper cover. Carefully remove all the paper in the paper bin along with any sheets that have fed part way into the printer.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Epson 1500 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Epson 1500 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Epson 1500, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Epson 1500 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Epson 1500, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Epson 1500.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Epson 1500. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Epson 1500 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
