Manuel d'utilisation / d'entretien du produit E-Force 1580 du fabricant Edelbrock
Aller à la page of 33
Edelbrock 4.6L Mustang GT Supercharger Part #1580 & #1585.
©2011 Edelbrock LLC Part #1580 & 1585 Brochure #63-1580 Rev . 1/11 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 2 Edelbrock LLC, 2700 California Street, T orrance , CA 90503 T oll-Free T ech Line: 1-800-416-8628 Office: 310-781-2222 Thank you for purchasing the Edelbrock 4.
©2011 Edelbrock LLC Part #1580 & 1585 Brochure #63-1580 Rev . 1/11 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 3 Due to the compl.
©2011 Edelbrock LLC Part #1580 & 1585 Brochure #63-1580 Rev . 1/11 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 4 INST ALLING A BOOST GAUGE OR PRESSURE TRANSDUCER Y our E-Force supercharger is equipped with two options for measuring boost.
©2011 Edelbrock LLC Part #1580 & 1585 Brochure #63-1580 Rev . 1/11 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 5 INST ALLA TION HARDW ARE P AR TS LIST Hardware Bag #1 Hardware Bag #2 Hardware Bag #3 (8x) - M6 x 1.
©2011 Edelbrock LLC Part #1580 & 1585 Brochure #63-1580 Rev . 1/11 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 6 INST ALLA TION HARDW ARE P AR TS LIST (Continued) Hardware Bag #6 (2x) - M6 x 1.
©2011 Edelbrock LLC Part #1580 & 1585 Brochure #63-1580 Rev . 1/11 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 7 I.
©2011 Edelbrock LLC Part #1580 & 1585 Brochure #63-1580 Rev . 1/11 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 8 7.
©2011 Edelbrock LLC Part #1580 & 1585 Brochure #63-1580 Rev . 1/11 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 9 11. Detach the mass airflow sensor electrical connector from the air filter outlet tube.
©2011 Edelbrock LLC Part #1580 & 1585 Brochure #63-1580 Rev . 1/11 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 10 18. Remove the fuel line lock clip and let it dangle. 19. Use a 5/8” fuel line removal tool to disconnect the fuel supply line from the fuel rails.
©2011 Edelbrock LLC Part #1580 & 1585 Brochure #63-1580 Rev . 1/11 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 11 25. 2005-2008 applications should remove the o-ring seals from the intake manifold and inspect them for damage.
©2011 Edelbrock LLC Part #1580 & 1585 Brochure #63-1580 Rev . 1/11 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 12 31. Use a 10mm socket to remove the two outer alternator bracket bolts, and an 8mm socket to remove the two inner alternator bracket bolts.
©2011 Edelbrock LLC Part #1580 & 1585 Brochure #63-1580 Rev . 1/11 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 13 37. Reach through the fender well with a 10mm socket to loosen the two nuts on each side that attach the front bumper cover to the body .
©2011 Edelbrock LLC Part #1580 & 1585 Brochure #63-1580 Rev . 1/11 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 14 42. Use large pliers or a clamp removal tool to detach both upper radiator hoses from the water crossover .
55. Hang the water pump on the passenger side outer bumper bolts while pushing the outlet hose onto the inlet nipple of the heat exchanger . Secure the hose with a clamp, and the wa ter pump bracket with two of the M8 flange nuts supplied. 56. Install the long 3/4” hose onto the driver side barb of the heat exchanger and secure it with a clamp.
©2011 Edelbrock LLC Part #1580 & 1585 Brochure #63-1580 Rev . 1/11 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 16 59. ‘05 a pplications should locate the red wire in pin 10, near the bottom of the connector .
66. Use a 10mm socket to attach the power wire to the power terminal on the fuse box 67. Route the water pump electrical connector below the fuse box and around the washer fluid reservoir and plug it into the intercooler water pump.
76. Reinstall the foam bumper insulator and secure it in place with the stock body pins. 77. Reconnect the fog lights and indicators, then replace the fascia onto the front of the car . Reach through the fender wells to reattach the nuts that secure it.
86. Install the smaller of the two Edelbrock supplied idler pulleys onto the alternator bracket with the open end facing the bracket. Secure it with a small amount of blue Loctite applied to the bolt saved in the previous step, then use a 13mm socket to torque it down to 18 ft/lbs.
X. Installing Spark Plugs (Not Included In 1585) NOTE: The follo wing steps only apply to Mustangs built prior to December , ‘07. Later applica tions have the proper heat range spark plug installed from the factor y and will not use the supplied plugs.
100. Insert the water crossover into the gap between the intercooler manifold and the and the supercharger drive pulley . There are no bolts that directly a ttach the crossover to the manifold, so it will need to be held stead y as the supercharger is installed.
107. Install the 3/8” vacuum hose attached to the rear of the manifold onto the brake booster nipple and secure it with the spring clamp provided. 108. Install the 1/4” vacuum hose attached to the rear of the manifold onto the fuel pressure sensor .
114. Place the tensioner in a cloth wrapped vice and use a grinding wheel or hacksaw to remove the stop. 115. Use a grinding wheel or file to ensure that the area that was ground down is smooth and free of burrs. 116. Use a 10mm socket to install the three tensioner brace bolts, making sure to line up the square holes.
121. Unbolt the power steering reser voir so that it can be pushed out of the way while installing the alternator . 122. Thread the serpentine belt through the alterna tor bracket and over the alternator pulley before securing the alternator to the bracket with the two M8 x 40mm bolts supplied in hardware bag #3.
127. Carefully remove the motor housing cap. 128. Install the plastic capped spring into the new Edelbrock supplied throttle body so that the pigtail end is hooked into the catch slot of the gear on the end of the throttle shaft. 129. Install the ETC motor over the plastic capped spring and tighten the screws that hold it in place.
136. Install the new high flow air filter in the airbox. 137. Use a T20 T orx driver to install the new MAF sensor in the air cover outlet tube, torque the two screws tha t retain it to 18 in/lbs., then reinstall the cover . 138. Install the throttle body elbo w onto the throttle body and secure it with the provided hose clamps.
144. Install the supplied heater hose onto the heater tube on the passenger side of the water crossover . 145. Verify that the coolant petcock is closed, then refill the coolant system. 146. Fill the intercooler system with a 50/50 blend of water and coolant poured into the recover y tank.
©2011 Edelbrock LLC Part #1580 & 1585 Brochure #63-1580 Rev . 1/11 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 28 153. Lower the driver side coil cover into place, orienting the bracket so that it lines up with the bolt provision below the TMAP sensor .
166. Read the description and press select. 167. The programmer will automa tically save a copy of your existing engine tune. Press select to continue. 168. T urn the ignition key to the ‘OFF’ position when prompted, but do not remove it. 169. T urn the ignition key to the ‘ON’ position when prompted, but do not a ttempt to start the car .
©2011 Edelbrock LLC Part #1580 & 1585 Brochure #63-1580 Rev . 1/11 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 30 Additional Supp.
©2011 Edelbrock LLC Part #1580 & 1585 Brochure #63-1580 Rev . 1/11 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 31 Complete Suspension Kits Edelbrock T ouring Suspension Kits include the best combination of components needed to upgrade your stock suspension and improve handling.
©2011 Edelbrock LLC Part #1580 & 1585 Brochure #63-1580 Rev . 1/11 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 32 Suspension Comp.
©2011 Edelbrock LLC Part #1580 & 1585 Brochure #63-1580 Rev . 1/11 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 33 T ubular T railing Arms are constructed of 1-1/4" diameter .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Edelbrock E-Force 1580 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Edelbrock E-Force 1580 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Edelbrock E-Force 1580, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Edelbrock E-Force 1580 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Edelbrock E-Force 1580, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Edelbrock E-Force 1580.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Edelbrock E-Force 1580. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Edelbrock E-Force 1580 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
