Manuel d'utilisation / d'entretien du produit 26 SI du fabricant ACDelco
Aller à la page of 32
26-SI ALTERNATOR 1G/287 4/96 PAGE 1G-28 7 HE A VY DUT Y BRUSHLESS AL TERN A T O R SER VICE MANU AL © 1 998 Delco Remy Inter national Inc. All Rights R eser ved.
PAGE 1G-287 4/96 26-SI ALTERNATOR FEA TURES 302.5 mm 198.0 mm SPECIFICATIONS: MAXIMUM SPEED: Continuous: 10,000 rpm Intermittent: 12,000 rpm AMBIENT TEMPERATURE LIMITS: -40°C to +85°C (-40°F to + 1.
26-SI ALTERNATOR 1G/287 4/96 PAGE PR ODUCT INFORMA TION AND SER VICE MANU A L 26-SI HEA VY DUTY BR USHLESS AL TERNA T O R CONTENTS INTRODUCTION The 26-SI series alternator is a brushless, heavy-duty integral charging system with built-in diode rectifier and voltage regulator, producing DC current for battery electrical systems.
PAGE 1G-287 4/96 26-SI ALTERNATOR FEATURES The 26-SI alternator is designed for a “one-wire” charging system configuration. “One-wire” refers to the minimum number of lead wire connections nec.
26-SI ALTERNATOR 1G/287 4/96 PAGE be passed through this circuit to aid in alternator turn-on. An “I” terminal is normally a threaded stud type with a 10- 24 thread.
PAGE 1G-287 4/96 26-SI ALTERNATOR TROUBLESHOOTING Trouble in the charging system will normally be indicated by one of the following: • Indicator light “on” with engine running. • Indicator light “off” with key on, engine not running. • Undercharged or overcharged battery.
26-SI ALTERNATOR 1G/287 4/96 PAGE - If indicator light does not come on with jumper lead in place, verify that alternator is properly grounded by touching jumper lead to another ground source. If lamp still does not light, locate and correct open circuit in indicator light circuit.
PAGE 1G-287 4/96 26-SI ALTERNATOR E. NO OUTPUT TEST EQUIPMENT NEEDED: • Voltmeter • Jumper Lead (18 ga. min; no fuse) Note that 26-SI alternators must be connected to a battery for the voltage sensing circuit to allow initial turn on (refer to section on Features).
26-SI ALTERNATOR 1G/287 4/96 PAGE 8. Recheck voltage at insulated battery terminal. Voltage should be higher than previous reading, but below 15 volts on 12-volt system (31 volts on 24 volt system). - If reading is lower than previous reading (Step 6), refer to section on No Output.
PAGE 1G-287 4/96 26-SI ALTERNATOR ALTERNATOR UNIT REPAIR CAUTION: Disconnect grounded cable at battery before removing or attaching battery cable at alternator output terminal. Otherwise, a tool shorted to the battery cable at the output terminal can quickly heat enough to cause a skin burn or damage the tool or cable.
26-SI ALTERNATOR 1G/287 4/96 PAGE FIELD COIL 3 . Disconnect 2 field leads from regulator (9) by removing 2 insulated regulator attachment screws (36). (See Fig. 12) Use ohmmeter to check resistance of field coil. Compare to Field Check ohms in Specifications at the end of this manual or from Service Specification Bulletin.
PAGE 1G-287 4/96 26-SI ALTERNATOR 6. Use ohmmeter or diode check function on multimeter to check diode trio (15). (See Fig. 15) Place negative ohmmeter lead on regulator lead (A) and use positive ohmmeter lead to check for continuity to each of the three phase leads (B, C, D).
26-SI ALTERNATOR 1G/287 4/96 PAGE RECTIFIER DIODES 8. Disconnect the 6 diode leads from the 3 diode junction studs by removing nuts. (See Fig. 17) Find the three output side diodes (11), which are installed in the heat sink (12). These diodes will be identical in polarity and will commonly have the same color of insulation on the diode lead wire.
PAGE 1G-287 4/96 26-SI ALTERNATOR 11. NOTICE: Do not hit diodes or diode mountings with a hammer or other tool. The shock of such an impact can damage the diode or other diodes in the same mounting. Use proper tools to press or pull diodes from their mountings.
26-SI ALTERNATOR 1G/287 4/96 PAGE housing (1) apart carefully. Guide stator leads and grommet (48) through hole as stator is pulled from housing. It may be necessary to push on grommet with a blunt instrument to unseat it from the housing. (See Fig. 24) 14.
PAGE 1G-287 4/96 26-SI ALTERNATOR 17. To replace rotor (4) or drive end bearing (7), (See Fig. 27) remove 4 bearing retainer attachment screws (28) from outside of housing (1). Lift rotor with bearing from housing, then pull bearing off of rotor shaft.
26-SI ALTERNATOR 1G/287 4/96 PAGE ALTERNATOR ASSEMBLY ASSEMBLY OF DE FRAME AND ROTOR INSTALL OR CONNECT 1. Press inner race for rectifier end bearing (3) onto short end of rotor shaft. Stop when race is 3.7 mm (.15 in.) above end of shaft. (See Fig. 29) 2.
PAGE 1G-287 4/96 26-SI ALTERNATOR Lightly lubricate outside surface of hinge bushing (44). Press hinge bushing into hole in lug on rectifier end housing (1). Install bushing flush with inside of lug to allow maximum distance between two hinge lugs for mounting.
26-SI ALTERNATOR 1G/287 4/96 PAGE 9. Push square plastic retainers for diode junction studs (13) into square holes in heat sink. Insert metal studs into holes in retainers and push in until shoulder on stud is seated against retainer. This spreads the retainer legs and secures the retainers in the holes.
PAGE 1G-287 4/96 26-SI ALTERNATOR 11. Place insulator (17b) on output terminal (17a) and install through hole in housing (1). (See Fig. 36) Install flat insulator washer (17c), aligning flat shoulders on terminal with slot in heat sink to fully seat terminal.
26-SI ALTERNATOR 1G/287 4/96 PAGE FINAL ALTERNATOR ASSEMBLY 15. CLEAN Inner race of rectifier end bearing (on rotor shaft) to prevent contamination of grease. 16. Align mounting lugs and assemble two halves of alternator (See Fig. 39), inserting rectifier end bearing inner race (on rotor shaft) into rectifier end bearing in rectifier housing.
PAGE 1G-287 4/96 26-SI ALTERNATOR 20. Place clip of red diode trio lead over hole in heat sink, then install insulator (51), flat washer (39), and heat sink attachment screw (31). (See Fig. 40) TIGHTEN Heat sink attachment screw to 3 N.m (26 lb. in.).
26-SI ALTERNATOR 1G/287 4/96 PAGE 25. TIGHTEN Regulator and mounting plate screws (holes A, B, C, and D) to 3 N.m (26 lb. in.). 26. Insert regulator lead support (57) into slots in housing (1). (See Fig. 43) Place one end of lead to diode heat sink lead (sense lead) over mounting hole in heat sink.
PAGE 1G-287 4/96 26-SI ALTERNATOR center hole. Replace gasket with a new one if at all questionable. Wipe edges of rectifier end housing and end cover gasket clean of foreign material. Place gasket and cover (19) onto housing (1) and install 7 rectifier cover attachment screw/washer assemblies (32 & 33).
26-SI ALTERNATOR 1G/287 4/96 PAGE ALTERNATOR BENCH TEST TEST EQUIPMENT NEEDED: • Alternator Test Stand (5000 rpm capability at least 5 HP) • Battery or Battery Set (fully charged) • Variable Car.
PAGE 1G-287 4/96 26-SI ALTERNATOR - If voltage increases above 15 volts on 12-volt system (or above 31 volts on 24-volt system), voltage is uncontrolled. Turn carbon pile load off and stop test stand. Recheck alternator for proper assembly. If alternator has been assembled properly, replace regulator as described under Unit Repair.
26-SI ALTERNATOR 1G/287 4/96 PAGE ALTERNATOR MOUNTING CAUTION: Failure to disconnect grounded battery cable at battery before removing or attaching alternator “BAT” terminal lead may result in an injury.
PAGE 1G-287 4/96 26-SI ALTERNATOR 5. Alternator belt to pulley. 6. If engine uses automatic belt tensioner (idler), skip to Step 7. NOTICE: Do not pry directly against rectifier end housing to adjust belt tension. Force must be applied to DE frame as described.
26-SI ALTERNATOR 1G/287 4/96 PAGE INSTALL OR CONNECT 11. Ground lead, if used, to ground hole in rectifier end housing, with ground screw/lockwasher assembly. (See Fig. 53) If ground lead is not used, be sure screw/ lockwasher is installed in ground hole and properly tightened to prevent entry of water or dirt.
PAGE 1G-287 4/96 26-SI ALTERNATOR 28 SERVICE PARTS Illus. No. Name Qty. 1. Housing, Rectifier End 1 2. Bearing, Rectifier End Outer Race 1 3. Bearing, Rectifier End Inner Race 1 4. Rotor Assembly 1 5. Stator Assembly 1 6. Frame, Drive End (DE) 1 7. Bearing, DE 1 8.
26-SI ALTERNATOR 1G/287 4/96 PAGE 29 27 46 48 5 49 29 8 4 21 22 7 6 43 28 23 42 52 26 34 20 33 32 19 47 35 36 38 40 41 9 25 15 16 30 24 18 45 56 2 3 44 1 17 50 10 57 55 12 13 25 11 14 53 51 39 31 37 2.
PAGE 1G-287 4/96 26-SI ALTERNATOR Delco Remy International, Inc. 2902 Enterprise Drive Anderson, IN 46013 For further information and specifications on these and other Delco Remy Products call: 1-800-DRA-0222 © Copyright DRI, 1G-500 10/97 Delco Remy is a registered trademark licensed by General Motors Corporation.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté ACDelco 26 SI c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du ACDelco 26 SI - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation ACDelco 26 SI, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le ACDelco 26 SI va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le ACDelco 26 SI, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du ACDelco 26 SI.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le ACDelco 26 SI. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei ACDelco 26 SI ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
