Manuel d'utilisation / d'entretien du produit 3528 du fabricant Edelbrock
Aller à la page of 39
1 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc T ABLE OF CONTENTS Part #3527 and #3528 Introduction......................................................................
2 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc PRIMAR Y KIT COMPONENTS ❑ Electronic Control Unit/System ECU ❑ Fuel.
3 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc TOOLS AND EQUIPMENT Use the following checklist for items needed.
4 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc MANIFOLD & CARBURETOR HEIGHT VS . PRO-FLO XT HEIGHT 1. Lay a straightedge (such as a yardstick) across the top of the air cleaner from front to back.
5 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc FUEL REQUIREMENTS Because the Pro-Flo XT system uses an Oxygen sensor, you must use unleaded fuel only. Leaded fuels will damage the O 2 sensor.
6 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc FUEL SYSTEM Because your Edelbrock Pro-Flo XT system controls fuel delivery very differently than a carburetor, some conversions to your fuel system are necessary.
RUBBER RETURN LINE METHOD Drill a 5/16-inch hole in the sending unit plate adjacent to where the main line enters the tank. This will be the hole for your return line. Insert a short length of 5/16-inch hard line (available at most radiator shops) into the hole and weld it to the sending unit plate.
HARD RETURN LINE METHOD Drill a 5/16-inch hole in the sending unit plate adjacent to where the main line, enters the tank. This will be the hole for your return line. Insert a length of 5/16-inch hard line (available at most radiator shops) into the hole and weld it to the sending unit plate.
9 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc NOTE: ALL WELDING AND SOLDERING OF THE FUEL SYSTEM MUST BE PERFORMED BY A PROFESSIONAL RADIA TOR AND/OR FUEL SYSTEM REP AIR SHOP .
10 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc INDUCTION SYSTEM The Edelbrock Pro-Flo XT system delivers fuel and air to the engine via the induction system consisting primarily of a manifold, 90mm air valve, fuel rails, and fuel injectors.
11 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc PRE-INST ALLA TION Before installing the induction system, take the following steps to ensure successful installation and performance 1.
12 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc GASKET SURF ACE PREP ARA TION CAUTION: Replace all gaskets as recommended. Do not use race-type non-embossed gaskets for street applications.
13 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc SENSORS The Edelbrock Pro-Flo XT system interprets overall engine operating conditions and fuel/spark requirements based on readings from sensors that measure specific engine conditions.
14 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc OXYGEN (O 2 ) SENSOR An oxygen sensor, installed on the header collector pipe, measures exhaust gas oxygen content and is used by the ECU to manage fuel delivery under closed loop control.
15 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc O 2 SENSOR INST ALLA TION The exhaust gas oxygen content is determined by the oxygen sensor. The sensor signals the ECU, which compensates when the air/fuel mixture is either rich or lean.
16 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc ENGINE HARNESS LA Y OUT.
17 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc MAIN SYSTEM HARNESS This diagram illustrates the chassis side of the Pro-Flo XT Main System Harness.
18 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc.
19 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc MAIN SYSTEM HARNESS This diagram illustrates the engine side of the Pro-Flo XT Main System Harness.
20 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc.
21 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc INST ALLA TION The Pro-Flo XT Main Harness is divided into two pieces, the engine harness and chassis harness. A bulkhead connector is provided as a pass through firewall connector.
22 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc ENGINE HARNESS J18: O 2 Sensor J19: Fuel Pump Coil Connectors Ignition.
23 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc The Coolant Temperature sensor attaches to the harness with Connector J15. The Manifold Absolute Pressure sensor attaches to the harness with Connector J17.
24 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc A. The ignition harness is attached to the main harness with the connector, as shown at left below, and at the coil with the ring terminals on the right below.
25 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc IGNITION SYSTEM The photo below shows how the distributor, ignition harness, and Main System Harness are connected. A KEY ON wire (Pink with black stripe) is also included in the Pro-Flo system.
26 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc ADDING AFTERMARKET IGNITION If you are wishing to use a MSD 6AL or MSD 6-Digital ignition with your Pro-Flo fuel injection, follow the wiring diagram below .
27 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc CUSTOMER INTERF ACE CONNECTOR A customer interface connector is included in the engine side harness.
28 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc To connect the ECU to your PC, plug the 34 pin ECU connector into the ECU.
29 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc 29 Pro-Flo EFI Installation Instructions SELECTING THE PROPER CALIBRA TION Application Kit Part No. Calibration No. Intake @ .
30 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc Priming The Fuel Pump Before the engine is started, the fuel pump must be primed to pressurize the system and purge the fuel line of all air.
31 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc Timing Adjustment Use a timing light to re-time your engine. 1. Remove spark plug from Number One cylinder. 2. Remove coil wire from distributor and ground it.
32 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc Idle Adjustment This procedure is a general recommendation, intended to help you tune up your Pro-Flo ® system.
33 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc ELECTRONIC ENGINE MANAGEMENT The Edelbrock Pro-Flo system uses the Spe.
34 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc PRO-FLO QUICK TUNING GUIDE This guide is based on our simple graph that shows the 24 fuel cells that you can tune in to result in a clean and powerful engine.
35 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc OPTIONAL PC TUNING FEA TURE To use the optional PC tuning feature, connect a DB9 serial extension cable to connector J25 of the main harness.
36 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc CALIBRA TION MODULE DIAGRAM.
37 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc P ART NUMBERS Edelbrock Pro-Flo Fuel Injection System ...................................................................
38 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc ( 1) Manifold Absolute Pressure sensor ( 1) Manifold Air T emperature .
39 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc SERVICE In the event that your Edelbrock Pro-Flo System should need servicing, return the unit pre-paid to the Edelbrock Service and Repair facility at 2700 California Street, Torrance, CA 90503.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Edelbrock 3528 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Edelbrock 3528 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Edelbrock 3528, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Edelbrock 3528 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Edelbrock 3528, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Edelbrock 3528.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Edelbrock 3528. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Edelbrock 3528 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
