Manuel d'utilisation / d'entretien du produit SRM - 230U du fabricant Echo
Aller à la page of 32
Grass T rimmer/Brush Cutter Operator's Manual MODEL SRM - 230U Serial Number 05001001 - 05002398 W ARNING DANGER Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual and a Safety Manual. Both must be read and understood for proper and safe operation.
2 I NTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will find both easy to use and full of helpful operating tips and SAFETY messages.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 3 IMPORTANT The enclosed message provides information necessary for the protection of the unit.
4 Shaft Decal W ARNING DANGER • This unit can be dangerous and cause serious injury if improperly used. To reduce injury risk to operator, helpers and bystanders, read and understand the Operator's and Safety manuals. • Blindness can occur from objects that are thrown or ricocheted even with shield in place.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 5 S AFETY I NSTRUCTIONS PERSONAL CONDITION AND SAFETY EQUIPMENT W ARNING DANGER Trimmer/Brush Cutter users risk injury to themselves and others if the trimmer/brush cutter is used improperly or safety precautions are not followed.
6 Repetitive Stress Injuries It is believed that overusing the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness, swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury (RSI).
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 7 SAFE OPERA TION W ARNING DANGER Do not operate this product indoors or in inadequately ventilated areas.
8 D ESCRIPTION The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, shield installation and other assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 9 9 14 17 19 20 21 10 Safety Video 22 1 2 3 4 5 6 8 7 18 15 16 11 12 13 23.
10 1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter. 2. THROTTLE TRIGGER LOCKOUT - This lever must be held during starting. Operation of the throttle trigger is prevented unless throttle trigger lockout lever is engaged.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 11 S PECIFICA TIONS * Install and use U-Handle when operating any model with blade. MODEL ----------------------------------------------------- SRM-230U Length ------------------------------------------------------- 1795 mm (70.
12 A SSEMBL Y PLASTIC SHIELD INST ALLA TION (For Nylon Line Operation) Tools Required: Screwdriver. Parts Required: Plastic Shield, Shield Plate, three (3) 5mm x 16mm screws. NOTE The plastic shield is for use with the Nylon Line Head only. Install Metal Shield when using plastic or metal blades.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 13 NOTE Model SRM-230U includes U-Handle, and necessary blade conversion parts. Blades are not provided with trimmer/ brushcutters and must be selected for type of cutting being performed. See page 15, "Blade Selection.
14 Install Blade Tools Required: Locking Tool, Scrench. Parts Required: Upper Plate w/ 20 mm pilot, Lower Plate, 10 mm Nut w/ L.H. threads, 2 x 25 mm Cotter Pin, Blade. 1 . Install upper plate (D) on splined PTO shaft, pilot side down. Blade installation requires Upper Plate (D) with 20 mm pilot.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 15 U - HANDLE INST ALLA TION Tools Required : 19 mm wrench, 4 mm hex socket wrench, Pliers Parts Required: U-Handle, Clamp w/screws, 8 mm x 55 mm hex bolt, 8 mm flat washer 1 .
16 4 . Bundle and secure ignition leads against engine housing with clip (I). J K I BALANCE AND ADJUST UNIT 1 . Loosen harness clamp screw. 2 . Put on harness and attach unit to harness. 3 . Slide harness clamp up (J) or down until unit balances with head approximately 50-75 mm (2 -3 in.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 17 Plastic/Nylon Blades may be used where ever the nylon line head is used. DO NOT use this blade for heavy weeds or brush! 8 Tooth Weed/Grass Blade (P/N 69600120331) is designed for grass, garden debris and thick weeds.
18 P RE - O PERA TION FUEL Fuel Requirements Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline or gasohol known to be good quality. Gasohol may contain up to 10% Ethyl (grain) alcohol or 15% MTBE (methyl tertiary-butyl ether). Gasohol containing methyl (wood) alcohol is NOT approved.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 19 O PERA TION ST ARTING COLD ENGINE W ARNING DANGER The attachment will operate immediately when the engine starts and could result in loss of control and possible serious injury.
20 ST ARTING W ARM ENGINE The starting procedure is the same as Cold Start except DO NOT close the choke, and do not depress throttle trigger to wide open position. NOTE If engine does not start after 5 pulls, use Cold Start Procedure. W ARNING DANGER The attachment should not move at idle, otherwise serious personal injury may result.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 21 STOPPING ENGINE 1. Throttle Release throttle and allow engine to return to idle before shutting off engine.
22 MAINTENANCE INTER V ALS / T N E N O P M O C M E T S Y S E C N A N E T N I A M E R U D E C O R P D ' Q E R L L I K S L E V E L R O Y L I A D E R O F E B E S U Y R E V E L E U F E R 3 S H T N O .
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 23 AIR FIL TER Level 1. Tools required: Cleaning brush 25 or 50 mm (1 or 2 in.) Parts required: 90008 REPOWER TM AIR & FUEL FILTER KIT. 1 . Close choke (Cold Start Position). This prevents dirt from entering the carburetor throat when the air filter is removed.
24 SP ARK PLUG Level 2. Tools Required: T-Wrench (combination socket wrench & screw driver) Feeler gauge, preferably a wire gauge. Soft Metal Brush. Parts Required: REPOWER TM Tune-Up Kit P/N 90074 1 . Remove spark plug and check for fouling, worn and rounded center electrode.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 25 1 . Remove spark plug lead. 2 . Remove two (2) muffler cover screws and muffler cover (A). 3 . Remove screw and arm rest (B). 4 . Remove engine cover (C). IMPORTANT DO NOT use a metal scraper to remove dirt from the cylinder fins.
26 1 . Remove two (2) muffler cover screws and muffler cover (A). 2 . Place piston at Top Dead Center (TDC) to prevent carbon/dirt from entering cylinder. 3 . Remove spark arrestor screen cover (B), gasket (C) and screen (D) from muffler body. 4 . Clean carbon deposits from muffler components.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 27 NOTE Every unit is run at the factory and the carburetor is set in compli- ance with emission regulations. This carburetor does not have acceleration and high speed adjustment needles. 1 .
28 NYLON LINE REPLACEMENT Level 1. Parts Required: ECHO 0.095" Nylon Trimmer Line 6 m (20 ft.) long. 1 . Shut engine off. Lay unit on the ground with head assembly up. 2. Hold drum (A) and firmly turn spool (B) CW (clockwise) until it disengages from the inner drive.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 29 8 . Hold drum (A) firmly and turn spool (B) CCW (counterclockwise) until it stops. DO NOT push in on spool when turning. 9 . Pull both lines out and trim to cut-off knife length. SHARPENING MET AL BLADES Three styles of metal blades are approved for use on the ECHO Brush Cutter.
30 T ROUBLESHOOTING W ARNING DANGER Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark near an open spark plug opening, otherwise serious personal injury may result.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 31 S TORAGE W ARNING DANGER During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result.
ECHO, INCORPORA TED 400 O AKWOOD R OAD L AKE Z URICH , IL 60047 www.echo-usa.com S ER VICING I NFORMA TION P ARTS Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer. When you do need to buy parts always have the Model Number and Serial Number of the unit with you.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Echo SRM - 230U c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Echo SRM - 230U - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Echo SRM - 230U, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Echo SRM - 230U va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Echo SRM - 230U, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Echo SRM - 230U.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Echo SRM - 230U. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Echo SRM - 230U ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
