FR
Dimplex logo
Notice d'utilisation officielle

Dimplex BF392SD

4 pages·214 KB·Cheminée d'intérieur·PDF·EN
Dimplex BF392SD
Table des matières 7 sections 7205760100REV03 · INSTALLATION GUIDE FOR THE ELECTRIC FIREPLACE · MODEL SPECIFICATIONS · FIGURE 1 1 · … AfficherMasquer
Page 1 of the Dimplex BF392SD user manual — FIGURE 1 1
Page 1 · cliquer pour agrandir
Page 1

7205760100REV03

Dimplex BF392SD — 7205760100REV03 diagram (page 1)
Fig. 1

INSTALLATION GUIDE FOR THE ELECTRIC FIREPLACE

LISTINGS AND CODE APPROVALS The BF series fireplaces have been tested in accordance with the UL 2021and CSA C22.2 No. 46 standards for fixed and location-dedicated electric room heaters.

MODEL SPECIFICATIONS

Model NumberDescriptionVoltage VoltsRated Power WattsRemote ControlAMPS 120Volt BF392SD39” two sided1201500STANDARD12.5
STEP-BY-STEP INSTALLATION (NotePlease read all instructions before installing)

1. Rough in framing opening following the recommended dimensions (Section A: Framing). NOTE Section A: Rough-in framing dimensions are based on ½” thick drywall. Rough-in framing dimensions will vary for different drywall thicknesses. 2. Allow 8” of service cable for connecting to the junction box on the fireplace. Remove the outer jacket and strip the individual conductors ½” from the end. 3. Loosen the screw securing junction box cover and remove the cover (FIGURE 1). 4. Remove knockouts if necessary or use the provided cable clamp. 5. Place unit in position in the opening, level with shims if necessary and attach unit to frame using nailing flanges provided. 6. Unit is factory wired for 120 volt installation. Wires L1, N & G are attached to the rear of the junction box cable clamp for easy access. 7. Wire a dedicated, 15 amp fused circuit with three wires (L1, N &G) rated for 120 volts. 8. Place all connectors inside the unit and replace the junction box cover, ensuring that the cable clamp grips only the jacket of service, thermostat and if applicable wall switch lines. WARNING Ensure method of installation does NOT obscure the air intake slots on bottom front of unit in any manner.

Junction Box Air Intake Slots

FIGURE 1 1

Page 2 of the Dimplex BF392SD user manual — RECOMMENDED WIRE AND FUSING REQUIREMENTS
Page 2 · cliquer pour agrandir
Page 2

SECTION A: FRAMING

Rough-in framing dimensions Firebox dimensions

This fireplace is a zero clearance design. Combustibles may be installed to the edge of the unit. Four nailing flanges on the sides of the unit are provided to facilitate installation. Insulation and vapor barrier should be placed a minimum of 2 inches from the unit.

SECTION B: RECOMMENDED POWER SUPPLY WIRE SPECIFICATIONS

For 120 volt installations use two conductor, non-metallic sheath cable with ground wire for the incoming power supply on fireplace inserts. Use the appropriate wire to meet local and national electrical codes for rated power consumption. Use appropriate wire to meet local and national electrical codes for rated power consumption.

RECOMMENDED WIRE AND FUSING REQUIREMENTS

VOLTSWIRE GAUGEFUSE RATING 120 VOLT14 GAUGE15 AMP
Page 3 of the Dimplex BF392SD user manual — SECTION A: FRAMING
Page 3 · cliquer pour agrandir
Page 3
Dimplex BF392SD — SECTION A: FRAMING diagram (page 3)
Fig. 2
Page 4 of the Dimplex BF392SD user manual — SECTION A: FRAMING
Page 4 · cliquer pour agrandir
Page 4
Dimplex BF392SD — SECTION A: FRAMING diagram (page 4)
Fig. 3

Approved for use in the United States and Canada

Poser une question sur : Dimplex BF392SD

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Dimplex BF392SD

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Dimplex BF392SD manuel PDF

4 pages·214 KB·Cheminée d'intérieur·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…