Manuel d'utilisation / d'entretien du produit Tintoretto du fabricant Digicom
Aller à la page of 32
TINTORETTO USER'S MANUAL Cod. 7D1109 rev . 1.0 02/98.
http://www .digicom.it.
Index I INDEX PREF ACE III 1. GENERALITY 1.1 1.1. PRODUCT P ACKAGE CONTENTS 1.1 1.1.2. PRODUCT OPTION (UPON REQUEST) 1.1 1.2. PRODUCT FEA TURES 1.1 2. INST ALLA TION 2.1 2.1. HARDWARE INST ALLA TION 2.1 2.1.1. TINTORETTO EXTERNAL 2.1 2.1.2. TINTORETTO INTERNAL ISA BUS 2.
Preface III PREF ACE All rights reserved; no part of this publication may be reproduced, stored in a retrieval system, or trasmitted in any form or by any means, electronic, otherwise, without the prior written permission of Digicom S.p.A.. The contents of this booklet may be modified without prior permission.
Generality 1.1 1. GENERALITY This operating manual describes the installation procedures and the main features of the Tintoretto ISDN modem family: Tintoretto external (PC or Macintosh), T intoretto internal ISA card (PC) and T intoretto PCMCIA (PC or Macintosh).
Installation 2.1 2. INST ALLA TION 2.1. HARDW ARE INSTALLA TION 2.1.1. TINTORETT O EXTERNAL See the following picture to connect your modem to the COM port of your PC and the ISDN cable to the BRI socket. See the following picture to connect your modem to the GEO port of your Macintosh and the ISDN cable to the BRI socket.
2.2 Installation 2.1.3. INTORETT O PC-CARD PCMCIA The T intoretto PC Card is compliant with any PCMCIA 2.0 socket.Insert the card in the PCMCIA slot of your computer the correct way up. The way up sign is on the modem sticker . Connect the ISDN cable to the external line inerface of Tintoretto.
Installation 2.3 3. From the window Install New Modem put a tick in the box “Don’t detect my modem: I will select it from a list” and select the button: Next.
2.4 Installation 5. Insert the Floppy disk or the CD ROM in the appropriate drive and from the window : Install from disk check that the correct driver letter appears showing where your Floppy/CD ROM is inserted (eg. A or D), then click the button OK.
Installation 2.5 Y our modem is installed and ready to make the first connection. 2.2.2. WINDOWS 95/NT4.0 PC CARD VERSION The installation of the driver for the PC Card (PCMCIA) is a little bit different for WIN95 release 4.00.950 or 4.00.950A or 4.00.
Description 3.1 3. DESCRIPTION 3.1. FRONT P ANEL EXTERNAL VERSION On the front panel are present LED that indicate the most important interface circuit in use and one push-button for TEST functions.
3.2 Description 3.3. HARDW ARE SETUP EXTERNAL VERSION Inside T intoretto is present a four position dip switch and some jumper berg for the hardware setup.
Description 3.3 3.3.2. HARDW ARE SETUP PC CARD VERSION Inside the external line interface of T intoretto PC Card are present two jumpers used to configure the ISDN line impedence.
3.4 Description Dip Switch Setting In the following table are described all the possible combination to set the communication port (COM1 to COM4) properly .
Description 3.5 ST ART DA T A P ARITY STOP TOT 17 1 1 1 0 18 0 1 1 0 17 0 2 1 0 18 1 1 1 1 The modem will accept even, odd, mark, or space. 3.4.1. A T COMMAND SET OF TINTORETTO COMMAND DESCRIPTION A T.
3.6 Description COMMAND DESCRIPTION *I Caller Identification function (CALLER ID) *K CTS (C106) during the handshaking *M MultiSubscriber Number function (MSN) *S Subaddress function *X Clock in Off-Line %A2 CSD call type (V .
Description 3.7 DS=0-19 Dial the dial string associated to the memory location (from 0 to 19) stored using &Z command Dn1*n2 Dial two number (n1 and n2) for MLPPP at 128Kbps. If the service access at 128Kbps is over a single telephone number the n1 is egual to n2.
3.8 Description Q Returns code Enable or disable the return codes from Tintoretto to the Computer . Q0 Messages transmission enabled Q1 Messages transmission disabled Q3 Reserved Q4 Reserved Q5 Reserv.
Description 3.9 NUMERIC VERBOSE 0O K 1 CONNECT 2R I N G 3 NO CARRIER 4 ERROR 6 NO DIAL TONE 7 BUSY 5 CONNECT 1200 10 CONNECT 2400 1 1 CONNECT 4800 12 CONNECT 9600 14 CONNECT 19200 28 CONNECT 38400 32 .
3.10 Description Z Load user configuration Reset T intoretto and load a user configuration stored in non volatile memory . Z0 Load user configuration n.
Description 3.11 &K4 Bi-directional software XON/XOFF (Tintoretto —> Computer and Computer —> Tintoretto) flow control. The T intoretto doesn’t transmit to the remote the XON/XOFF chars received from the Computer . &K8 Unidirectional software XON/XOFF (Tintoretto —> Computer) flow control.
3.12 Description &S C107 (DSR) control Establish how the C107 (DSR) will operate. &S0 C107 (DSR) is always ON. &S1 C107 (DSR) function as standard; DSR is ON when the connection is established and will be OFF when Tintoretto hangs-up. Store: S21 Default=&S0 &T Enable or disable Loop test Allow to select the of loop test.
Description 3.13 &Y Define the user configuration to be loaded at power on Define what user configuration, stored using the &W command, must be loaded at T intoretto power on. &Y0 Load the user configuration stored to user memory 0. &Y1 Load the user configuration stored to user memory 1.
3.14 Description *M MultiSubscriber Number function (MSN) The MultiSubscriber Number permits the association of maximum 8 consecutive numbers to a BRI access of the national plan number . There’s a principal number with the last digit always equal to “0” and associated with it is an auxiliary number that may vary between “1” and “7”.
Description 3.15 %A2=2 V .120 protocol. %A2=5 PPP protocol at 64Kbps %A2=6 MLPPP protocol at 128Kbps Store: S15 Default=%A2=1 %A3 Select Data Channel %A3=2 Preferred B1 channel. If busy, Tintoretto try to use the B2 channel %A3=3 Forced B1 channel. If busy , T intoretto hangs-up the communication %A3=4 Preferred B2 channel.
3.16 Description It is important to remember that the CCITT rules for the asincronus V25bis function, provide a format of 7 data bit Even parity . T o return in A T command from V25bis command set (%V1 or %V3), turn ON the Tintoretto pushing the TEST push-button for minimum 5 seconds.
Description 3.17 !N2=”nnnn” where “nnnn” is composed of prefix + number (p.e. 331263122) !N2? show the stored MultiSubscriber number T o enable the MultiSubscriber Number function, please also make reference to the A T*M command.
3.18 Description S1 RING count Number of ring in a period of 8 seconds. V alue Unit Function 0 RING No ring in a period of 8 seconds 1-5 RING RING count Default=0 T ype:Non Storable S2 ESCAPE sequence character V alue Unit Function 0-127 ASCII Contain the ESCAPE sequence character .
Description 3.19 S13 Call W aiting time V alue Unit Function 0 sec. Call Waiting time disable 0-255 1 sec. Defines the duration of buzzer/TEST led flash when arrives a new call. Default=30 T ype:Storable S25 DTR control V alue Unit Function 0-255 sec/100 Sets the length of time that the modem will ignore DTR for before hanging up.
3.20 Description 6 = 2400 bps 15 = 4800 bps 16 = 7200 bps 17 = 9600 bps 18 = 12000 bps 19 = 14400 bps 27 = 19200 bps 50 = 38400 bps (asyncronous only) 51 = 48000 bps (syncronous only) 53 = 64000 bps (.
Diagnostic 4.1 4. DIAGNOSTIC 4.1. DIAGNOSTIC ACTIV A TION FOR PC CARD VERSION If T intoretto is turned off and on, starts automatically the internal self test diagnostic to understand particular problem before the normal function.
Declaration CE of Conformity V DECLARA TION OF CONFORMITY This product satisfies the basic requirements of Electromagnetic Compatibility and Safety of the below indicated Directive: l 91/263/EEC of 29 april 1991 (Directive 93/68/CEE of july 22,1993 and Directive 93/97/ CEE of 29 october 1993).
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Digicom Tintoretto c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Digicom Tintoretto - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Digicom Tintoretto, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Digicom Tintoretto va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Digicom Tintoretto, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Digicom Tintoretto.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Digicom Tintoretto. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Digicom Tintoretto ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
