Manuel d'utilisation / d'entretien du produit R610 du fabricant Dell
Aller à la page of 184
Dell™ PowerEdge™ R610 Sy stems Hardware Owner’ s Manual.
Notes, Cautions, and W arnings NOTE: A NOTE indicates important information that helps you make better use of your computer . CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed. WARNING: A W ARNING indicates a potential for property damage, personal injury , or death.
Contents 3 Contents 1 About Y our Sy stem . . . . . . . . . . . . . . . . . . 11 Accessing Sy stem Features During Startup . . . . . . . 11 Front-Panel Featu res and Indicators . . . . . . . . . . 12 LCD Panel Features . . . . . . . . . . . . . . . . .
4 Contents 2 Using the Sy stem Setup Program and UEFI Boot Manager . . . . . . . . . . . . . . . . . 57 Choosing the Sy stem Boot Mode . . . . . . . . . . . . 57 Entering the Sy s tem Setup Program . . . . . . . . . . . 58 Responding to Error Messages .
Contents 5 Entering the iDRAC Confi guration Utility . . . . . . 76 3 Installing Sy stem Components . . . . . . . . 77 Recommended T ools . . . . . . . . . . . . . . . . . . . 77 Inside the Sy stem . . . . . . . . . . . . . . . . . . . . 77 Removing and Replacing the Optional Front Bezel .
6 Contents Installing an Expansion Card . . . . . . . . . . . . 90 Removing an Expansion Card . . . . . . . . . . . . 92 Expansion-Card Risers . . . . . . . . . . . . . . . . . . 92 Removing an Expansion-Card Riser . . . . . . . . 92 Replacing an Expa nsion-Card Riser .
Contents 7 Replacing the Plastic Fan Guide . . . . . . . . . . 108 Optical Drive . . . . . . . . . . . . . . . . . . . . . . . 108 Removing an Optical Drive . . . . . . . . . . . . . 109 Installing an Optical Drive . . . . . . . . . . . . . 110 Integrated Storage Controller Card .
8 Contents SAS Backplane . . . . . . . . . . . . . . . . . . . . . 132 Removing the SAS Backplane . . . . . . . . . . 132 Installing a SAS Backplane . . . . . . . . . . . . 135 Sy stem Board . . . . . . . . . . . . . . . . . . . . . . 135 Removing the Sy stem Board .
Contents 9 T roubleshooting an Internal USB Key . . . . . . . . . . 151 T roubleshooting an Optical Drive . . . . . . . . . . . . 151 T roubleshooting Hard Drives . . . . . . . . . . . . . . 152 T roubleshooting a SAS Controller . . . . . . . . . . . .
10 Contents 7 Getting Help . . . . . . . . . . . . . . . . . . . . . . 167 Contacting Dell . . . . . . . . . . . . . . . . . . . . . 167 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 Index . . . . . . . . . . . . . . . . . . . .
About Y our Sy stem 11 About Y our Sy stem Accessing Sy stem Features During Startup The following keystrok es provide access to system features during startup. Key stroke Description <F2> Enters the System Setup progra m. See "Using the System Setup P rogram and UEFI Boot Manager.
12 About Y our Sy stem Front-Panel Features and Indicators Figure 1-1. Front Panel Indicators and Features Item Indicator , Button, or Connector Icon Description 1 P ower-on indicator , power button The power -on indicator lights when the system power is on.
About Y our Sy stem 13 2 NMI button Used to trou bleshoot software and device driver errors when using certain operating systems. This button can be pressed using the end of a paper clip. Use this button only if directed to do so by qualified support pe rsonnel or by the operating system's documentation.
14 About Y our Sy stem LCD Panel Features The system's LCD panel provides system information and status messages to signify when the system is operating correctly or when the system needs attention. See "LCD Status Messages" for information on specific status codes.
About Y our Sy stem 15 Figure 1-2. LCD Panel Features Home Screen The Home screen displays user -configu rable information about the system. This screen is displayed during norm al system operation when ther e are no status messages or errors present.
16 About Y our Sy stem Setup Menu View Menu Option Description DR AC Select DHCP or Static IP to configure the network mode. If Static IP is selected, the available fields are IP , Subnet ( Sub ), and Gateway ( Gtw ). Select Setup DNS to enable DNS and to vi ew domain addresses.
About Y our Sy stem 17 Hard-Drive Indicator Patterns for RAID Figure 1-3. Hard Drive Indicators T emperature Displays the temperature of the system in Celsius or F ahrenheit. The display format can be configured in the "Set home" submenu of the Setup menu (see "Setup Menu").
18 About Y our Sy stem Drive-Status Indicator Pattern (RAID Only) Description Blinks green two times per second Identify drive/preparing for r emoval Off Drive ready for insertion or r emoval NOTE: The drive status indicator remains off until all hard drives are initialized after sy stem power is applied.
About Y our Sy stem 19 Back-Panel Features and Indicators F igure 1-4 shows the controls, indicat ors, and connectors located on the system's back panel.
20 About Y our Sy stem 11 system identification button T urns the system ID modes on and off. The identification buttons on the front and back panels can be used to locate a particular system within a rack.
About Y our Sy stem 21 Power Indicator Codes An LED indicator on the power button indicates when power is supplied to the system and the system is operational. The power supplies have an indicator that shows whether power is present or whether a power fault has occurred.
22 About Y our Sy stem Figure 1-5. Power Supp ly Status Indicator NIC Indicator Codes Figure 1-6. NIC Indicators 1 power supply status 1 link indicator 2 activity indicator 1 1 2.
About Y our Sy stem 23 LCD Status Messages The following LCD messages refer to events r ecorded in the System Event Log (SEL). (The messages are shown here in "simple" te xt format.) F or information on the SEL and configuring system management settings, see the systems management software documentation.
24 About Y our Sy stem T o resolve the problem and r emove the LCD message, r efer to the corrective actions in the following table. NOTE: The following LCD status messages are displayed in the Simple format. See “Setup Menu“to select the format in which the messages are displayed.
About Y our Sy stem 25 E1216 3.3V Regulator failure. Reseat PCIe cards. 3.3V voltage regulator has failed. Remove and reseat the PCIe expansion car ds. If the problem persists, see "T roubleshooting Expansion Cards." E1229 CPU # VCORE Regulator failure.
26 About Y our Sy stem E1311 Fan module ## RPM exceeding range. Check fan. RPM of specified fan in specified module is outside of intended operating range. See "T roubleshooting System Cooling P roblems." E1313 Fan redundancy lost. Check fans.
About Y our Sy stem 27 E141F CPU # protocol error. Power cycle AC. The system BIOS has reported a processor protocol error . Remove AC power to the system for 10 seconds and restart the system. If the problem persists, see "Getting Help." E1420 CPU Bus parity error.
28 About Y our Sy stem E161C Power Supply # (### W) lost AC power. Check PSU cables. Specified power supply is attached to the system, but it has lost its AC input. Check the AC power source for the specified power supply . If the problem persists, see "T roubleshooting P ower Supplies.
About Y our Sy stem 29 E1710 I/O channel check error. Review & clear SEL. The system BIOS has reported an I/O channel check. Check the SEL for details of the error message. Remove AC power to the system for 10 seconds and restart the system. If the problem persists, see "Getting Help.
30 About Y our Sy stem E1714 Unknown error. Review & clear SEL. The system BIOS has determined there has been an error in the system, but is unable to determine its origin. Remove AC power to the system for 10 seconds and restart the system. If the problem persists, see "Getting Help.
About Y our Sy stem 31 E171F PCIe fatal error on Bus ## Device ## Function ## The system BIOS has reported a PCIe fatal error on a component that resides in PCI configuration space at bus ##, device ##, function ##. Remove and reseat the PCIe expansion car ds.
32 About Y our Sy stem E1A15 SAS cable B failure. Check connection. SAS cable B is missing or bad. Reseat the cable. If the problem persists, replace cable. If the problem persists, see "Getting Help." E1A1D Control panel USB cable not detected.
About Y our Sy stem 33 E2015 DMA Controller failure. Power cycle AC. DMA controller failure. Remove A C power to the system for 10 seconds and restart the system. If the problem persists, see "Getting Help." E2016 Interrupt Controller failure.
34 About Y our Sy stem E201B Keyboard Controller error. Power cycle AC. Keyboar d controller failur e. Remove AC power to the system for 10 seconds and restart the system. If the problem persists, see "Getting Help." E201C SMI initializatio n failure.
About Y our Sy stem 35 E2110 Multibit Error on DIMM ##. Reseat DIMM. The DIMM in slot "##" has had a multi-bit error (MBE). See "T roubleshooting System Memory.
36 About Y our Sy stem W1228 RAID Controller battery capacity < 24hr. W arns predictively that the RAID battery has less than 24 hours of charge left. Allow RAID battery to charge to gr eater than 24 hours of sustained charge. If problem persists, replace the R AID battery .
About Y our Sy stem 37 Sy stem Messages System messages appear on the screen to notify you of a possible problem with the system. NOTE: If you receive a sy stem message not listed in the table, check .
38 About Y our Sy stem Alert! iDRAC6 not responding. Rebooting. The iDR AC6 is not responding to BIOS communication either because it is not functioning properly or has not completed initialization. The system will reboot. W ait for the system to reboot.
About Y our Sy stem 39 Alert! Power required exceeds PSU wattage. Check PSU and system configuration. Alert! Continuing system boot accepts the risk that system may power down without warning. The system configuration of processor(s), memory modules, and expansion cards may not be supported by the power supplies.
40 About Y our Sy stem BIOS Update Attempt Failed! Remote BIOS update attempt failed. Retry the BIOS update. If the problem persists, see "Getting Help." Caution! NVRAM_CLR jumper is installed on system board NVRAM_CLR jumper is installed in the clear setting.
About Y our Sy stem 41 CPUs with different cache sizes detected. Mismatched processors are installed. Ensure that all processors have the same cache size, number of cores and logical processors, and power ratings, and that they are properly installed.
42 About Y our Sy stem Embedded NIC x and NIC y : OS NIC=DISABLED, Management Shared NIC= DISABLED The OS NIC interface is disabled in BIOS. The Management Shared NIC interface is disabled in management tools. Check the system management software or the System Setup program for NIC settings.
About Y our Sy stem 43 Invalid PCIe card found in the Internal_Storage slot! The system halted because an invalid PCIe expansion card is installed in the dedicated storage controller slot. Remove the PCIe expansion card and install the integrated storage controller in the dedicated slot.
44 About Y our Sy stem Memory address line failure at address , read value expecting value F aulty or improperly installed memory modules. See "T roubleshooting System Memory." Memory double word logic failure at address , read value expecting value F aulty or improperly installed memory modules.
About Y our Sy stem 45 Mirror mode disabled. For mirror mode, DIMMs must be installed in pairs. Pairs must be matched in size and geometry. The memory configuration does not match the setting in BIOS. The BIOS setting has been disabled. Reconfigure the memory modules for Memory Mirroring mode.
46 About Y our Sy stem PCI BIOS failed to install PCIe device BIOS (Option ROM) checksum failure detected during shadowing. Cables to expansion car d(s) loose; faulty or improperly installed expansion car d(s). Reseat the expansion car d(s). Ensure that all appropriate cables are secur ely connected to the expansion car d(s).
About Y our Sy stem 47 Read fault Requested sector not found F aulty USB device, USB medium, optical drive assembly , hard drive, or har d- drive subsystem. Replace the USB medium or device. Ensure that the USB, backplane, or SA T A cables are properly connected.
48 About Y our Sy stem Shutdown failure General system error . Run the online diagnostic tests. See "R unning the System Diagnostics." The amount of system memory has changed Memory has been added or removed or a memory module may be faulty .
About Y our Sy stem 49 The following DIMMs should match in geometry: x , x , ... Invalid memory configuration. The specified DIMMs do not match in size, number of ranks, or number of data lanes. Ensure that the memory modules are installed in a valid configuration.
50 About Y our Sy stem Timer chip counter 2 failed F aulty system board. See "Getting Help." TPM configuration operation honored. System will now reset. A TPM configuration command has been e nter ed. The system will reboot and ex ecute the command.
About Y our Sy stem 51 The iDRA C6 Enterprise card flash memory may be corrupted. Restore the flash memory using the latest version on support.dell.com . See the iDR AC6 user’s guide for instructions on performing a field replacement of the flash memory .
52 About Y our Sy stem Warning: A fatal error has caused system reset! Please check the system event log! A fatal system error occurred and caused the system to reboot.
About Y our Sy stem 53 Warning! PSU mismatch. PSU redundancy lost. Check PSU. A High Output power supply and an Energy Smart power supply are installed in the system at the same time. Install two High Output or two Energy Smart power supplies in the system.
54 About Y our Sy stem W arning Messages A warning message alerts you to a po ssible problem and prompts you to respond befor e the system continues a task. F or example, before you format a diskette, a message will warn you that you may lose all data on the disk ette.
About Y our Sy stem 55 Other Information Y ou May Need WARNING: See the safety and regulatory inf ormation that shipped with your sy stem. Warranty information may be included within this document or as a separate document. • The rack documentation included with your rack solution describes how to install your system into a rack.
56 About Y our Sy stem.
Using the Sy stem Setup Pr ogram and UEFI Boot Manager 57 Using the Sy stem Setup Program and UEFI Boot Manager The System Setup program is the BIOS pr ogram that enables you to manage your system hardwar e and specify BIOS-l evel options.
58 Using the Sy stem Setup Prog ram and UEFI Boot Manager Entering the Sy stem Setup Program 1 T urn on or restart your system. 2 P r ess <F2> after you see the following message: <F2> = System Setup NOTE: The sy stem will not respond unti l the USB keyboard is active.
Using the Sy stem Setup Pr ogram and UEFI Boot Manager 59 Sy stem Setup Options Main Screen Figure 2-1. Main Sy stem Setup Program Screen NOTE: The options for the Sy stem Setup pr ogram change base d on the sy stem configuration.
60 Using the Sy stem Setup Prog ram and UEFI Boot Manager PCI IRQ Assignment Displays a screen to change the IRQ assigned to each of the integrated devices on the PCI bus, and any installed expansion car d that requir es an IRQ. Serial Communication ( Off default) See "Serial Communication Screen.
Using the Sy stem Setup Pr ogram and UEFI Boot Manager 61 Memory Settings Screen Processor Settings Screen Option Description System Memory Size Displays th e amount of system memory . System Memory T ype Displays the type of system memory . System Memory Speed Displays the system memory speed.
62 Using the Sy stem Setup Prog ram and UEFI Boot Manager SA T A Settings Screen Virtualization T echnology ( Disabled default) NOTE: Disable this feature if your sy stem will not be running virtualization software. Enabled permits virtualization software to use the virtualization technology inco rporated in the processor .
Using the Sy stem Setup Pr ogram and UEFI Boot Manager 63 Boot Settings Screen Option Description Boot Mode ( BIOS default) CAUTION: Switching the boot mode could prevent the sy stem from booting if the operating sy stem was not installed in the sa me boot mode.
64 Using the Sy stem Setup Prog ram and UEFI Boot Manager Integrated Devices Screen Option Description Integrated SAS/R AID Controller ( Enabled default) Enables or disables the i ntegrated storage controller . User Accessible USB P orts ( All P orts On default) Enables or disables the user -accessible USB ports.
Using the Sy stem Setup Pr ogram and UEFI Boot Manager 65 PCI IRQ Assignments Screen Serial Communication Screen Embedded Video Controller ( Enabled default) Enables or disables BIOS support for th e integrated video controller . NOTE: Integrated video can only be disabled if a video expansion card is installed.
66 Using the Sy stem Setup Prog ram and UEFI Boot Manager Embedded Server Management Screen Power Management Screen F ailsafe Baud Rate ( 115200 default) Displays the failsafe baud rate used for console redir ection. BIOS attempts to determine the baud rate automatically .
Using the Sy stem Setup Pr ogram and UEFI Boot Manager 67 CPU P ower and P erformance Management Options are OS Control , Active P ower Controller , Custom , or Maximum P erformance .
68 Using the Sy stem Setup Prog ram and UEFI Boot Manager Sy stem Security Screen Option Description System P assword Displays the current status of the passwor d security feature and allows a new system passwor d assignment and verification. NOTE: See "Using the Sy stem Password" for more information.
Using the Sy stem Setup Pr ogram and UEFI Boot Manager 69 Exit Screen P r ess <Esc> to exit the System Setup program; the Exit scr een displays: • Save Changes and Exit • Discard Changes and Exit • Return to Setup TPM Clear ( No default) CAUTION: Clearing the TPM will lose all encryption key s in the TPM.
70 Using the Sy stem Setup Prog ram and UEFI Boot Manager Entering the UEFI Boot Manager NOTE: Operating sy stems must be 64-bit UEFI-compatible (for example, Microsoft ® Windows Server ® 2008 x64 version) to be installed from the UEFI boot mode. DOS and 32-bit operating sy stems can only be installed from the BIOS boot mode.
Using the Sy stem Setup Pr ogram and UEFI Boot Manager 71 UEFI Boot Manager Screen UEFI Boot Settings Screen Option Description Continue The system attempts to boot to devices starting with the first item in the boot order .
72 Using the Sy stem Setup Prog ram and UEFI Boot Manager Sy stem Utilities Screen Sy stem and Setup Password Features NOTE: For a forgotten password, see "D isabling a Forgotten Password." Y our system is shipped without the system password featur e enabled in BIOS.
Using the Sy stem Setup Pr ogram and UEFI Boot Manager 73 When a system password is not assi gned and the passwor d jumper on the system board is in the enabled position, System P assword is Not Enabled and P assword Status is Unlocked . T o assign a system password: 1 V erify that P assword Status is Unlocked .
74 Using the Sy stem Setup Prog ram and UEFI Boot Manager When P assword Status is Lo ck ed , you must type the passwor d and press <Enter> when prompted at reboot. If an incorrect system passwor d is ent ered, the system displays a message and prompts you to re-enter your passwor d.
Using the Sy stem Setup Pr ogram and UEFI Boot Manager 75 NOTE: The setup password can be the same as the sy stem password. If the two passwords are different, the setup password can be used as an alternate sy stem password. The sy stem password cannot be used in place of the setup password.
76 Using the Sy stem Setup Prog ram and UEFI Boot Manager iDRAC Configuration Utility The iDR AC Configuration Utility is a pr e-boot configuration environment that allows you to view and set para meters for the iDR AC6 and for the managed server .
Installing Sy stem Components 77 Installing Sy stem Components Recommended T ools • Key to the system k eylock • #1 and #2 Phillips screwdrivers • #8, #15 and #10 T orx screwdrivers • W rist grounding strap Inside the Sy stem CAUTION: Many repairs may only be done by a certified service technician.
78 Installing Sy stem Components Figure 3-1. Inside the Sy stem Removing and Replacing the Optional Front Bezel 1 Unlock the keylock at the left end of the bezel. 2 Lift up on the release la tch next to the k ey lock. 3 Rotate the left end of the bezel away from the front panel.
Installing Sy stem Components 79 Figure 3-2. Removing and Replac ing the Optional Front Bezel T o replace the optional bezel, hook the right end of the bezel onto the chassis, then fit the free end of the bezel onto the system. Secur e the bezel with the keylock.
80 Installing Sy stem Components 4 P ull the tag to the left until it diseng ages from the slot in the chassis to release the right portion of the tag. 5 Remove the tag. Replacing the Information T ag 1 Remove the front bezel. See " Removing and Replacing the Optional F ront Bezel .
Installing Sy stem Components 81 Figure 3-3. Removing and Replacing the Sy stem Cover Closing the Sy stem 1 Lift up the latch on the cover . 2 Place the cover onto the chassis and offs et it slightly towards the back of the system, so that the two hooks on the back edge of the cover fit over the corresponding tabs on the back edge of the chassis.
82 Installing Sy stem Components Hard Drives Y our system supports up to six 2.5-inch SAS, SA T A, or SSD hard drives. See F igure 3-1. • Mixed har d-drive configurations of SAS and SA T A drives are allowed. In this configuration, two SAS drives must be installed in hard-drive slots 0 and 1 only .
Installing Sy stem Components 83 Figure 3-4. Removing or Installing a Hard-Drive Blank Installing a Hard-Drive Blank Align the hard-drive blank with the d rive bay and insert the blank into the drive bay until the release lever clicks into place.
84 Installing Sy stem Components CAUTION: T o maintain proper sy stem cooling, all empty hard-drive bay s must have drive blanks installed. Installing a Hot-Swap Hard Drive CAUTION: When installing a hard drive, ensure that the adjacent drives are fully installed.
Installing Sy stem Components 85 b Insert the hard-drive carrier into the drive bay until the carrier contacts the backplane. c Close the handle to lock the drive in place. Removing a Hard Drive From a Hard-Drive Carrier Remove the screws from the slide rails on the har d-drive carrier and separate the hard drive from the carrier .
86 Installing Sy stem Components Figure 3-6. Installing a Hard Drive Into a Drive Carrier 1 screws (4) 2 drive carrier 3 hard drive 4 SAS screw hole 1 3 2 4.
Installing Sy stem Components 87 Power Supplies Y our system supports the following power supply modules: • 717- W High Output power supply • 502- W Ener gy Smart power supply (the default power supply option for this system) NOTE: The sy stem does not support a mixed in stallation of High Output and Energy Smart power supplies.
88 Installing Sy stem Components Figure 3-7. Removing an d Replacing a Power Supply Installing a Power Supply 1 On a system with redundant power su pplies, verify that both power supplies are the same type and have the same maximum output power . NOTE: The maximum output power (shown in watts) is listed on the power supply label.
Installing Sy stem Components 89 Removing the Power Supply Blank If you are installing a second power supply , r emove the power supply blank in bay PS2 by pulling outward on the blank. CAUTION: T o ensure proper sy stem cooling , the power supply blank must be installed in power supply bay PS2 in a non-redundant configuration.
90 Installing Sy stem Components T able 3-1. Expansion-Card Installation Order Installing an Expansion Card CAUTION: Many repairs may only be done by a certified serv ice technician.
Installing Sy stem Components 91 c Close the expansion-car d latch. See Figur e 3-8. Figure 3-8. Installing or Re moving an Expansion Card 6 Connect any cables to the expansion car d.
92 Installing Sy stem Components Removing an Expansion Card CAUTION: Many repairs may only be done by a certified serv ice technician. Y ou should only perform troubles hooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Installing Sy stem Components 93 1 T urn off the system, including any attached peripherals, and disconnect the system from the electrical outlet. 2 Open the system. See "Opening the System." 3 If an expansion car d is installed in th e e xpansion slot, remove the car d now .
94 Installing Sy stem Components Figure 3-9. Installing or Removi ng an Expansion-Card Riser 4 2 1 5 9 8 3 6 7.
Installing Sy stem Components 95 Replacing an Expansion-Card Riser 1 T o install an expansion-car d riser , align the board with the riser guide posts on the system board. See F igure 3-9. 2 Lower the expansion-card riser into place until the e xpansion-car d riser connector is fully seated.
96 Installing Sy stem Components 3 P osition the internal SD module tray so the tabs on the underside of the tray fit into the corresponding hooks on the chassis (item 3 in F igure 3-10), then lower the opposite edge of th e card into place. See F igure 3-10.
Installing Sy stem Components 97 Removing the Internal SD Module Card CAUTION: Many repairs may only be done by a certified service technician. Y ou should only perform trou bleshooting and simple rep airs as authorized in your product documentation, or as directed by the online or telephone service and support team.
98 Installing Sy stem Components 5 P ress the car d into the card slot to lock it into place. 6 Close the system. See "Closing the System." 7 Reconnect the system to power and restart the system. Removing an Internal SD Flash Card CAUTION: Many repairs may only be done by a certified serv ice technician.
Installing Sy stem Components 99 NOTE: T o avoid interference with other co mponents, the ma ximum allowable dimensions of the USB key are 24 mm (. 94 in) wide x 79 mm (3.11 in) long x 8.6 mm (.33 in) high. 1 T urn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.
100 Installing Sy stem Components 1 T urn off the system, including any at tached peripherals, and disconnect the system from the electrical outlet. 2 Open the system. See "Opening the System." 3 Remove the fan bracket. See "Removing the F an Assembly.
Installing Sy stem Components 101 Installing a VFlash Media Card 1 Locate the VFlash media slot at the back corner of the system. See "Back- P anel F eatures and Indicators" for the location of the media slot. 2 W ith the label side facing up, insert the contact-pin end of the SD card into the card slot on the module.
102 Installing Sy stem Components When the front of the card is fully seated, the plastic standoffs snap over the edge of the card. Figure 3-12. Installing or Remo ving an iDRAC6 Enterprise Card 6 Reinstall the left expansion car d, if applicable. See "Installing an Expansion Card.
Installing Sy stem Components 103 3 Open the system. See "Opening the System." 4 Remove the VFlash media from the iDR AC6 Enterprise Car d. See"Removing a VFlash Media Card." 5 If installed, remove the e xpansion car d from expansion-car d riser 2.
104 Installing Sy stem Components 3 Locate the ISCSI_KEY connector on the system board. See F igure 6-1. 4 Insert the NIC hardwar e k ey into the connector . See F igure 3-13. Figure 3-13. Installing a NIC Hardware Key 5 Close the system. See "Closing the System.
Installing Sy stem Components 105 NOTE: IF F AN6 is installed in a single-proces sor configuration, the fan will still be operational. Removing a Cooling Fan CAUTION: Many repairs may only be done by a certified service technician.
106 Installing Sy stem Components Replacing a Cooling Fan 1 Ensure that the fan is oriented corr ectly . Orient the fan module so that the side with the power cable faces towards the back of the system. 2 Slide the fan module into the fan assembly until the fan is fully seated.
Installing Sy stem Components 107 Figure 3-15. Removing an d Replacing the Fan Assembly Replacing the Fan Assembly 1 Being careful not to pinch the cables connected to the backplane board, replace the fan assembly in the chassis, and close the two latches to secur e the assembly .
108 Installing Sy stem Components 3 Close the system. See "Closing the System." Removing the Plastic Fan Guide 1 T urn off the system, including any at tached peripherals, and disconnect the system from its electrical outlet. 2 Open the system.
Installing Sy stem Components 109 NOTE: DVD devices are data only . Removing an Optical Drive CAUTION: Many repairs may only be done by a certified service technician. Y ou should only perform trou bleshooting and simple rep airs as authorized in your product documentation, or as directed by the online or telephone service and support team.
110 Installing Sy stem Components Figure 3-16. R emoving the Optical Drive Installing an Optical Drive CAUTION: Many repairs may only be done by a certified serv ice technician.
Installing Sy stem Components 111 8 If not already done, connect the power cable to D VD_PWR and the interface cable to SA T A_A on the system board. See F igure 6-1. 9 Replace the front bezel, if applica ble. See "Removing and Replacing the Optional F ront Bezel.
112 Installing Sy stem Components a Grasp the expansion car d by its edges, bend outwar d on both card- edge guides, and carefully r emove the car d from the e xpansion-card connector .
Installing Sy stem Components 113 c Unlatch the fan assembly and lift it far enough out of the chassis to route the SAS cable along the inside of the chassis, underneath the plastic retention clip. Replace the fan assembly and close the latches. See F igure 3-14, "Removing a Cooling F an," and "Replacing a Cooling F an.
114 Installing Sy stem Components 6 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals. RAID Battery The information in this section applies only to systems with the optional battery-cached PERC controller car d.
Installing Sy stem Components 115 3 Disconnect the battery cable from th e PERC controller . See F igure 3-17 for the battery connection location. NOTE: Pay attention to the routing of the cable in the ch assis for reinstallation. 4 Remove the battery cable from the cable clip on the system board near est PSU #2.
116 Installing Sy stem Components Sy stem Memory Y our system supports DDR3 register ed DIMMs (RDIMMs) or unbuffer ed ECC DIMMs (UDIMMs). Single and dual-rank DIMMs can be 1067- or 1333-MHz, and quad-rank DIMMs can be 1067-MHz. The system contains 12 memory sockets split into two sets of six sock ets, one set per each processor .
Installing Sy stem Components 117 • T wo memory modules per ch annel supports up to 1067 MHz. – F or quad-rank memory modules: • One memory module per channel supports up to 1067 MHz. • T wo memory modules per ch annel are limited to 800 MHz, regar dless of memory module speed.
118 Installing Sy stem Components A minimal single-channel configuratio n of one 1-GB memory module per processor is also supported in this mode. T able 3-2 and T able 3-3 show sample memory configurations that follow the appropriate memory guidelines stated in this section.
Installing Sy stem Components 119 Advanced ECC 2-GB none X XX X XX 4 8 all 8 16 all 4-GB none X XX X XX 8 16 all 16 32 all 8-GB none X XX X XX 16 32 all 32 64 all Mirroring 2-GB none X XX X XX 4 8 2 4 8 16 4 8 4-GB none X XX X XX 8 16 4 8 16 32 8 16 8-GB none X XX X XX 16 32 8 16 32 64 16 32 T able 3-3.
120 Installing Sy stem Components Installing Memory Modules CAUTION: Many repairs may only be done by a certified serv ice technician. Y ou should only perform troubles hooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Installing Sy stem Components 121 Figure 3-18. Installing and Removing a Memory Module 6 Align the memory module's edge connect or with the alignment key of the memory module socket, and insert th e memory module in the sock et.
122 Installing Sy stem Components 11 If the value is incorrect, one or mo r e of the memory modules may not be installed properly . Repeat step 2 through step 10 of this procedure, checking to ensure that the memory modules ar e firmly seated in their sockets.
Installing Sy stem Components 123 support team. Damage due to servicing that is not authoriz ed by Dell is not covered by your warranty . Read and follow the safety instru ctions that came with the product. 1 P rior to upgrading your system, down load and install the latest system BIOS version from support.
124 Installing Sy stem Components 7 Gently lift the heat sink off of the processor and set the heat sink aside upside down (thermal grease side facing up). CAUTION: The processor is held in its socket under strong pressure. Be aware that the release lever can spring up suddenly if not firmly grasped.
Installing Sy stem Components 125 Figure 3-20. Installing and Removing a Processor Installing a Processor CAUTION: Many repairs may only be done by a certified service technician.
126 Installing Sy stem Components 2 If you are adding a second processor for the first time, r emove the heatsink blank and the processor blank from th e vacant processor socket. Removing the blanks is similar to removing a processor . See "Removing a P rocessor.
Installing Sy stem Components 127 9 R un the system diagnostics to verify that the new processor operates correctly . See "R unning the System Diagnostics" for information about running the diagnostics. Sy stem Battery Replacing the Sy stem Battery CAUTION: Many repairs may only be done by a certified service technician.
128 Installing Sy stem Components Figure 3-21. R eplacing the Sy stem Battery 3 Locate the battery socket. See F igure 6-1. CAUTION: T o avoid damage to the battery connec tor , you must firmly support the connector while installing or removing a battery .
Installing Sy stem Components 129 8 Enter the System Setup program to conf irm that the battery is operating properly . See "Entering the System Setup P rogram." 9 Enter the correct time and date in the System Setup program's Ti m e and Date fields, and configure the oth er settings for your system.
130 Installing Sy stem Components Figure 3-22. C ontrol Panel Removal 16 Using a T10 T orx driver , remove the t wo screws that secur e the display module to the system chassis.
Installing Sy stem Components 131 Installing the Control Panel Display Module 1 Insert the display module into the chassi s cutout and secure with the two T orx screws. See F igure 3-22. 2 Attach the replacement panel to the front of the display module.
132 Installing Sy stem Components Installing the Control Panel Board 1 Install the front panel screw in the scr ew hole located beneath the left USB connector . See F igure 3-22. 2 Install the control panel board in the system chassis and secur e with the three T orx scr ews.
Installing Sy stem Components 133 5 Disconnect the power cable from the end of the SAS backplane. 6 Disconnect the SAS data cables from the backplane. 7 Remove the SAS backplane from the system: a While pulling the two blue latches towards the front of the system, slide the backplane upward.
134 Installing Sy stem Components Figure 3-23. Removing and Ins talling a SAS Backplane 1 SAS backplane power cable 2 SAS backplane 3 SAS A cable 4 SAS B cable 5 retention hooks (2) 6 backplane retent.
Installing Sy stem Components 135 Installing a SAS Backplane 1 Install the SAS backplane: a Lower the backplane into the system, being careful to avoid damaging components on the face of the board.
136 Installing Sy stem Components 3 Remove the power supply(s). S ee "Removing a P ower Supply." 4 Remove all expansion car ds and the integrated storage controller car d. See "Removing an Expansion Card" and "Removing the Integrated Storage Controller Card.
Installing Sy stem Components 137 Figure 3-24. Removing and Installing the Sy stem Board 1 retention pin 2 sy stem board assembly 1 2.
138 Installing Sy stem Components Installing the Sy stem Board 1 Unpack the new system board and r emove the label placar d that is inserted in the memory module socket. 2 Remove the labels from the placar d and affix them to the system information panel on the front of the system.
Installing Sy stem Components 139 9 Install all expansion car ds. See "Installing an Expansion Car d." 10 Reinstall the integrated storage controller card.
140 Installing Sy stem Components.
T roubleshooting Y our Sy stem 141 T roubleshooting Y our Sy stem Safety First—For Y ou and Y our Sy stem CAUTION: Many repairs may only be done by a certified service technician.
142 T roubleshooting Y our Sy stem T roubleshooting the V ideo Subsy stem 1 Check the system and power co nnections to the monitor . 2 Check the video interface cabling from the system to the monitor . 3 If two monitors are attached to the system, disconnect one monitor .
T roubleshooting Y our Sy stem 143 4 If a device causes the same problem, power down the device, replace the USB cable if applicable, and power up the device. If the problem persists, replace the device. If all troubleshooting fails, see "Getting Help.
144 T roubleshooting Y our Sy stem 4 Ensure that the appropriate drivers ar e installed and the protocols ar e bound. See the NIC's documentation. 5 Enter the System Setup program and confirm that the NIC ports are enabled. See "Integrated Devices Screen.
T roubleshooting Y our Sy stem 145 • F an assembly • P rocessors and heat sinks • Memory modules 4 Let the system dry thoroughly for at least 24 hours. 5 Reinstall the processors and heat sink s, memory modules, power supplies, and fan assembly .
146 T roubleshooting Y our Sy stem • Memory modules • Har d-drive carriers 4 Ensure that all cables ar e properly connected. 5 Close the system. See "Closing the System." 6 R un the system board tests in the system diagnostics. See "R unning the System Diagnostics.
T roubleshooting Y our Sy stem 147 CAUTION: If troubleshooting a PSU mismatch er ror , replace only the power supply with the flashing ind icator . Swapping the oppos ite power supply to create a matched pair can result in an error condition and unexp ected sy stem shutdown.
148 T roubleshooting Y our Sy stem T roubleshooting a Fan CAUTION: Many repairs may only be done by a certified serv ice technician. Y ou should only perform troubles hooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
T roubleshooting Y our Sy stem 149 3 T urn on the system and attached periph erals and note any messages on the screen or LCD panel. Go to step 12 if an error message appear s indicating a fault with a specific memory module. 4 Enter the System Setup program and check the system memory setting.
150 T roubleshooting Y our Sy stem 17 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals. 18 As the system boots, observe any error message that appears on the scr een or the LCD panel on the front of the system.
T roubleshooting Y our Sy stem 151 12 T urn on the system and attached peripherals and check if the SD card is functioning. If the problem is not resolved, see "Getting Help." T roubleshooting an Internal USB Key CAUTION: Many repairs may only be done by a certified service technician.
152 T roubleshooting Y our Sy stem support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty . Read and follow the safety instructions th at came with the product. 1 If applicable, remove the bezel. See "Removing the F ront Bezel.
T roubleshooting Y our Sy stem 153 Depending on the results of the dia gnostics test, proceed as needed through the following steps. 2 If applicable, remove the bezel. See "Removing the F ront Bezel." 3 If your system has a SAS or PERC co ntroller and your har d drives are configured in a R AID array , perform the following steps.
154 T roubleshooting Y our Sy stem 3 Restart the system and press the applicable k ey sequence to enter the configuration utility program: • <Ctrl><C> for a SAS controller • <Ctrl><R> for a PER C controller See the controller's documentation fo r information about configuration settings.
T roubleshooting Y our Sy stem 155 2 Ensure that the device drivers for the tape drive ar e installed and ar e configured corr ectly . See your tape drive documentation for more information about device drivers. 3 Reinstall the tape-backup software as instructed in the tape-backup software documentation.
156 T roubleshooting Y our Sy stem NOTE: When troubleshooting an expansion card, see the documentation for your operating sy stem an d the expansion card.
T roubleshooting Y our Sy stem 157 d Close the system. See "Closing the System." e R un the appropriate diagnostic test. If the tests fail, see "Getting Help." T roubleshooting the Processors CAUTION: Many repairs may only be done by a certified service technician.
158 T roubleshooting Y our Sy stem 12 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals. 13 R un the appropriate online diagnostic test. If the test fails, the processor is faulty . S ee "Getting Help.
Running the Sy st em Diagnostics 159 Running the Sy stem Diagnostics If you experience a problem with your system, run the diagnostics befor e calling for technical assist ance. The purpose of the diagnostics is to test your system's hardwar e without r equiring a dditional equipment or risking data loss.
160 Running the Sy stem Diagnostics • T emporarily suspend testing if an e rror is detected or terminate testing when a user -defined error limit is r eached. • View help messages that briefly describe each test and its parameters. • View status messages that inform yo u if tests ar e completed successfully .
Running the Sy st em Diagnostics 161 Sy stem Diagnostics T esting Options Click the testing option in the Main Menu window . Using the Custom T est Options When you select Custom T est in the Main Menu window , the Customize window allows you to select the device(s) to be tested, select specific options for testing, and view the test results.
162 Running the Sy stem Diagnostics • T est Iterations — Selects the number of times the test is run. • Continue on F ailure — Enables the tests to continue without user intervention in the event that one of the tests has failed.
Jumpers and Connectors 163 Jumpers and Connectors This section provides specific informa tion about the system jumpers. It also provides some basic information on jumpers and switches and describes the connectors on the various boards in the system.
164 Jumpers and Connectors 1 T urn off the system, including any at tached peripherals, and disconnect the system from the electrical outlet. 2 Open the system. See "Opening and Closing the System." 3 Move the password jumper to the "disable d" position to clear the passwor d.
Jumpers and Connectors 165 Figure 6-1. Sy stem Board Connectors 1 2 3 4 6 7 9 10 8 11 13 14 12 16 17 15 5 18.
166 Jumpers and Connectors T able 6-2. Sy stem Board Connectors Connector Label Description 1 IO_RISER2 expansion-car d riser 2 connector 2 - system board assembly r etention pin 3 IO_RISER1 expansion.
Getting Help 167 Getting Help Contacting Dell F or customers in the United States , call 800- WWW -DELL (800-999-3355). NOTE: If you do not have an active Inter net connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog.
168 Getting Help.
Glossary 169 Glossary A — Ampere(s). AC — Alternating current. ACP I — Advanced Configuration and P ower I nterface. A standard interface for enabling the operating system to dire ct configuration and power management. ambient temperature — The temperature of the ar ea or room wher e the system is located.
170 Glossary CPU — Central processing uni t. See processor . DC — Direct curr ent. DDR — Double-data rate. A technology in memo ry modules that potentially doubles the data rate by transferring data on both the rising and falling pulses of a clock cycle.
Glossary 171 reprogrammed using a softwar e utility . FTP — F ile transfer protocol. g — Gram(s). G — Gravities. Gb — Gigabit(s); 1024 megabits or 1,073,741,824 bits. GB — Gigabyte(s); 1024 megabytes or 1,073, 741,824 bytes. However , when r eferring to hard-drive capacity , the term is usually rounded to 1,000,000,000 byte s.
172 Glossary KB — Kilobyte(s); 1024 bytes. Kbps — Kilobit(s) per second. KBps — Kilobyte(s) per second. kg — Kilogram(s); 1000 grams. kHz — Kilohertz. KVM — Keyboar d/video/mouse. KVM refers to a switch that allows selection of the system from which the video is displayed and for which the keyboar d and mouse ar e used.
Glossary 173 memory — An area in your system that stor es basic system data. A system can contain several different forms of memory , such as integrated memory (ROM and R AM) and add-in memory modules (DIMM s). memory key — A portable flash memory storage device integrated with a USB connector .
174 Glossary PDU — P ower distribution unit. A power so urce with multiple power outlets that provides electrical power to serve rs and storage systems in a rack. peripheral — An internal or extern al device, such as a disk ette drive or k eyboard, connected to a system.
Glossary 175 SAS — Serial-attached SCSI. SA T A — Serial Advanced T echnology Attach ment. A standard interface between the system board and storage devices. SCSI — Small computer system interface. An I/O bus interface. SD card — Secure digital flash memory car d.
176 Glossary referring to har d-drive capacity , the term is usually rounded to 1,000,000,000,000 bytes. TCP/IP — T ransmission Control Protocol/Internet P rotocol. termination — Some devices (such as the last device at each end of a SCSI cable) must be terminated to prevent r eflections and spurious signals in the cable.
Glossary 177 virtualization — The ability via software to shar e the r esources of a single computer across multiple environments. A single physic al system may appear to the user as multiple virtual systems able to host multiple operating systems. W — W att(s).
178 Glossary.
Index 179 Index A Advanced ECC memory mode, 117 B back-panel features, 19 batteries troubleshooting, 1 4 6 battery troubleshooting the R AID card b a t t e r y , 153 battery (R AID) installing, 1 1 4 .
180 Index diagnostics advanced testing options, 1 6 1 testing options, 1 6 1 using Dell P owerEdge Diagnostics, 1 5 9 when to use, 1 6 0 DIMMs See memory modules (DIMMs).
Index 181 power supply blank, 8 9 processor , 1 2 5 R AID battery , 1 1 4 SAS backplane board, 1 3 5 SAS controller , 1 1 2 SD card, 9 7 internal USB cable installing, 1 0 0 removing, 9 9 J jumpers (s.
182 Index P passwor d setup, 7 4 system, 7 2 passwor ds disabling, 1 6 3 PERC 6/I battery cable installing, 1 1 5 r e m o v i n g , 114 phone numbers, 167 POST accessing system features, 1 1 power ind.
Index 183 installing, 1 1 2 r e m o v i n g , 111 SAS controller daughter card troubleshooting, 1 5 3 SAS RAID controller daughter card troubleshooting, 1 5 3 SD card installing, 9 7 removing, 9 8 t r.
184 Index hard drive, 1 5 2 i n te r n a l U S B k e y , 150-151 k e y b o a r d , 142 memory , 1 4 8 N I C, 143 optical drive, 1 5 1 power supplies, 1 4 6 processors, 1 5 7 SAS R AID controller daugh.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Dell R610 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Dell R610 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Dell R610, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Dell R610 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Dell R610, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Dell R610.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Dell R610. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Dell R610 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.