Manuel d'utilisation / d'entretien du produit 132.24607 du fabricant Craftsman
Aller à la page of 20
Operator's Manual RIDER COOLING SYSTEM Model No. 132.24607 CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. IMPORTANT: For replacement parts or assembly questions call 800-320-MIST. • Safety • Assembly • Operation • Maintenance • Troubleshooting Sears, Roebuck and Co.
SAFETY RULES .................................... 2 HARDWARE CONTENTS ..................... 3 CARTON CONTENTS ............................ 4 ASSEMBLY .......................................... 5 OPERATION ........................................ 14 MAINTENANCE .
A ...... iii!iii iii_jiiiii ii_iiHiiiTi ¸ii -¸ ? B f ii // H S D E REF. QTY. DESCRIPTION A 2 Hex Bolt, 5/16"-18 x1-1/4" B 2 Flat Washer, 7/8" OD C 4 Cap Screw, 5t16-!8" x 3/4&quo.
AA. Power Unit BB. Misting Nozzle Assembly CC. Mounting Bracket DD. 9/16" Drill Bit BB /.
Tools Required ½" Socket Wrench w/Extension Allen Wrenches Power Drill Adjustable Wrench Mounting Power Unit To Tractor NOTE: If there is a 2 or 3 bin bagger installed on your tractor, you will need to remove the bagger from the tractor before proceeding.
Once all bolts have been installed, tighten all nuts using allen wrench and socket on both bolts and nuts, Mounting Misting Nozzle Assembly to Tractor The rider cooling system misting assembly is designed to be installed on the tractor's dash. Some tractors come equipped with rider cooling system mounting locations.
Using supplied 9/16" drill bit (DD), drill hole through the dash at the bottom of the mounting location. Use caution not to damage anything in the engine com- partment while drilling hole. Step 2 • Install rubber washer (H) onto the misting arm assembly (BB), by sliding over hoses and threaded section until seated against mounting flange.
Step 3 IMPORTANT: If you have not already done so, you must disconnect the negative (-) termi- nal of the battery before completing the next steps. • Repeat with the remaining dash adapter nut (F) until seated on bottom surface of the nut already installed.
Connecting Power Unit to Misting Arm Assembly Step 1 • Locate supply lines and power connector at the power unit (AA) and uncoil to full length. Step 2 • When the supply lines have exited the underside of the tractor body, feed the supply lines and power connector along tractor chassis into engine compartment.
Step 3 • Locate BLACK supply tube from power unit and BLACK supply tube from misting nozzle assembly. • Remove protective caps from the BLACK supply tube and filter attached to the BLACK tube. • Connect BLACK supply tube from misting arm assembly to the filter installed on the BLACK supply tube from the power unit.
Step 3 • Connect power unit's female connector to Maintenance Minder. Step 4 • From inside the engine compartment, locate tractor power supply connector. NOTE: The tractor power supply connector will resemble the female connector supplied with the power unit.
Finalizing System Installation Step 1 • Review the illustration below to familiarize yourself with the suggested locations of the routing clips (G) EACH SIDE OF DASH SUPPORT IMPORTANT: Do not kink hoses exiting the power unit.
Step 2 • Using a supplied cable tie (J) organize any excess length of supply tubes and stow behind battery (or along fuel tank if equipped). Secure supply tubes to electrical supply lines of tractor at convenient locations to prevent line damage during tractor operation.
KNOW YOUR RIDER COOLING SYSTEM Read this owner's manual before operating. Compare the illustration below with your rider cooling system to familiarize yourself with the various features and their locations. POWER SWITCH Controls the power to the system's pump.
HOW TO START YOUR RIDER COOLING SYSTEM • With the tractor key in "ON" position, toggle power switch on unit to "ON" posi- tion. NOTE: It is normal to experience a delay from the time the system is turned on to the deliv- ery of mist from the nozzle.
CUSTOMER RESPONSIBILITIES VIA1 NTENANCE SCHEDULE sill in dates as you complete "egular service Sh eck for loose fasten ers Slean Exterior Zmpty Water Tank Clean Basket Filter Sor_dition Water Tank :_eplace Ah-fWater Filters Read and follow the maintenance schedule and the maintenance procedures listed in this section.
• Empty water tank completely, replace cap, and run system to evacuate all wa- ter in supply lines. • Store misting nozzle assembly by folding over dash of tractor. • Ensure the power switch on the power unit is in the "OFF" position. • Clean debris from venting on rear of power unit.
NOTES: ]8.
NOTES: ]9.
For expert troubleshooting and home solutions advice: manage home www,managemyhome,com For repair- in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling syste.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Craftsman 132.24607 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Craftsman 132.24607 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Craftsman 132.24607, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Craftsman 132.24607 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Craftsman 132.24607, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Craftsman 132.24607.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Craftsman 132.24607. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Craftsman 132.24607 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
