Manuel d'utilisation / d'entretien du produit AIRCAP3702IAK9 du fabricant Cisco Systems
Aller à la page of 44
G ETTING S TARTED G UIDE Cisco Aironet 3700 Series Access Points 1 About this Guide 2 Introduction to the Access Point 3 Safety Instructi ons 4 Unpacking 5 Configuratio ns 6 Access Point Ports and Con.
2 Created: Novembe r, 2013, 78-214 74-01.
3 1 About this Guide This Guide provides in structions on how to inst all and configure your Cisco Aironet 3700 Series Access Point and how to install availab le radio modules. This guide al so provides mounting instructions and limited troubleshooting procedures.
4 – Throughput, forwarding, and filtering performan ce scaled to meet 3 spatial stream, 1.3-Gbps data-rates • 32 MB flas h size • 802.11af/at – CDP (Cisco Discovery Protocol) • 2.4 GHz and 5 GHz 802.11n radios with the following features: – 4TX x 4RX – 3-spatial streams, 1.
5 Warning This product relies on the building’s installatio n for short-circuit (overcurre nt) protection. Ensure tha t the protective device is rated not greater than: 20A.
6 4 Unpacking To unpack the access point, follow these steps: Step 1 Unpack and remove the acce ss point and the accessory kit from the shipping box. Step 2 Return any pa cking material to the shippi n g container and save it for future use. Step 3 Verify that you have receiv ed the items listed below.
7 • AIR-ANT2524DG-R • AIR-ANT2524V4C-R • AIR-ANT2544V4M-R • AIR-ANT2566P4W-R Internal Antennas The 3702I model access point is configured with four dual-band inverted-F antennas, and two 2.
8 6 Access Point Ports and Connectors The 3702E model access point has external antenna co nnectors and the LED indictor on th e top of the model, as shown in Figure 1 .
9 Figure 2 Access Point LED Indi cator (t op)—3702I Model The ports and connections on the bottom of the access point are shown in Figure 3 . Figure 3 Access Point Ports and Co nnection s (bottom)-A.
10 7 Configuring the Access Point This section describes how to connect the access point to a wireless LAN controller. Because the configuration process takes place on the control ler, see the Cisco Wireless LAN Controller Configuration Guide for additional information.
11 Note You cannot edit or query any access point using the control ler CLI if the name of the access point contains a space. Note Make sure that the controller is set to the curren t time.
12 • Access point mounting options: below a suspended ceiling, on a fla t horizontal surface, or on a desktop. Note You can mount th e access point above a suspended ceiling but yo u must purchase additional mounting ha rdware: See “Mounting th e Access Po int” sec tion on pag e 15 for additional information.
13 Pre-Installation Configuration Setup The pre-installation configuration setup is shown in Figure 4 . Figure 4 Pre-Installation Conf iguration Setup To perform pre-installation configuration, perform th e following steps: Step 1 Make sure that the Cisco wireless LAN controller DS port is connected to the network.
14 e. CAPWAP UDP ports must not be blocked in the network. f. The access point must be able to find the IP address of the controller. This can be accomplished using DHCP, DNS, or IP subnet broadcast. This guide describes the DHCP method to convey the controller IP addres s.
15 Step 3 Configure the access point if required. Use the controller CLI, controller GUI, or Cisco Prime Infrastructure to customize the access- point-specific 802.11ac network settings. Step 4 If the pre-installation configuration is successf ul, the Status LED is green indicating normal operation.
16 Step 2 Observe the access point LED (for LED descriptions, see “Checking the Access Point LED” section on page 19 ). a. When you power up the access point, it begins a power-up sequence that you can verify by observing the access point LED. If the power-up sequence is successful, the discovery and join process begins.
17 Step 3 Peel off the label from the back of the 3700 se ries ac cess point t o reveal the module port connector. Step 4 Align the module’s connector w ith the connector on the back o f the access point and click the module into place. 1 Openings for modu le’s antennas.
18 Step 5 Screw down the thumb screws on the module. Note If the screws are not tightened, the module will not be recognized and may not operate correctly. Make sure not to over-ti ghten, only hand-tighten the screws. Step 6 Power up the access point.
19 11 Troubleshooting If you experience difficulty getti ng your access point installed and running, lo ok for a solution to your problem in this guide or in additional access po int documentation. These, and other documents, are available on Cisco.com.
20 Figure 5 Access Point LED Location The access point status LED indicates va rious conditions and are described in Table 1 . 1 Status LED Table 1 LED Status Ind ications Message Type Status LED Mess.
21 Association status Green Normal operating condition, but no wireless client associated Blue Normal operating condition, at least one wireless client association Operatin g status Blinking blue Soft.
22 Troubleshooting the Ac cess Point Join Process Access points can fail to join a controller for many reasons: a R ADIUS auth orization is pending; self-signed certific ates are not enabled on the co ntro ller; the access point’s and controller’s regulatory domains don’t match, and so on.
23 • An access point running software release 5.2 or later has been newly deploy ed. • An existing access point run nin g software release 5.2 or la ter ha s been reset after clearing the configuration.
24 12 Declarations of Conformity and Regulatory Information This section provides declarations of conformity and regulatory information for the Cisco Aironet 3700 Series Access Points and a ny additional modules that can be installed into the Cisco Aironet 3700 Series Access Point.
25 2. This device must accept any interference received, incl uding interference that may cause undesired operation. This device operates in the 5150-5250MHz and 54 70-5725MH z bands and is therefore restricted to indoor operation only per FCC guidance.
26 VCCI Statement for Japan Warning This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Techn ology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference.
27 Guidelines for Operating Cisco Aironet Access Points in Japan This section provides guidelines for avoiding interf erence when operating Cisc o Aironet access points in Japan.
28 Statement 371—Power Cable and AC Adapter English Translation When installing th e product, please use the provided or designated connection cables/power cables/AC adaptors.
29 This device complies with Class B Limits of Industry Canada. Operatio n is subject to the follo wing two conditions: 1. This device may not cause harmful interferenc e, and 2. This device must accept any interference received, incl uding interference that may cause undesired operation.
30 Afin de r_duire le risque d'interf_rence aux autres utilisateurs, l e type d'antenne et son gain doivent _tre choisis de fa_on ˆ ce que la puissance isotrope rayonn_e _quiva lente (p.i.r.e.) ne soit pas sup_rieure au niveau requis pour obtenir une communication satisfaisante.
31 Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC.
32 The following standards were applied: EMC—EN 301.489-1 v1.8.1; EN 301.489-17 v2.1.1 Health & Safety—EN60950-1: 2005; EN 50385: 2002 Radio—EN 300 328 v 1.7.1; EN 301.893 v 1.5.1 The conformity assessment procedure ref erred to in Article 10.
33 This device also conforms to the EMC requirem ents of the Medical Devices Directi ve 93/42/EEC. Note This equipment is intended to be used in a ll EU and EFTA countries. Outdoor use may be restricted to certain frequencie s and/or may require a license fo r operation.
As such the systems are designed to be operated as to avoid contact with the antennas by the end use r. It is recommended to set the system in a location where the antennas can remain at least a minim.
35 This Device Meets the In dustry Canada Guidelines for Exposure to Radio Waves The 3700 series device in cludes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electrom agnetic fields) as referenced in Heal th Canada Safety Code 6.
36 • United Kingdom, National Radiological Protection Board at this URL: www.nrpb.org.uk • Cellular Telecommunications Association at this URL: www .
37 English Translation Administrative Rules for Low- power Radio-Frequency Devices Article 12 For those low-power radio-frequenc y devices that have alr eady recei ved a type-a pproval , compani es, business units or users should not change its freque ncies, increase its power or change its original features and functions.
38 English Translation Low-power Radio-frequency Devices Technical Specifications Operation of Cisco Aironet Access Points in Brazil This section contains special information for oper ation of Cisco Aironet access points in Brazil.
39 English Translation This equipment operates on a secondary ba sis and consequently must accept harmful interference, including interference from stations of the sa me kind. This equipment may n ot cause harmful interference to systems operating on a primary basis.
Step 1 Enter configuration mode at the Cisco IOS CLI. Step 2 Create the DHCP pool, inc luding the necessary parameters su ch as default router and name server.
14 Access Point Specifications Table 2 lists the technical speci fications for 3700 series acc ess points. Table 2 Access Poi nt Specifications Category Specification Dimensions (LxWxD) 8.68 x 8.68 x 1.84 in. (22.04 x 22.0 4 x 4.67 cm) Weight 1.9 lbs (0.
.
43.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco .com/go/trademarks . Third-party trad emarks mentio ned are the property of their respec tive owners.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Cisco Systems AIRCAP3702IAK9 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Cisco Systems AIRCAP3702IAK9 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Cisco Systems AIRCAP3702IAK9, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Cisco Systems AIRCAP3702IAK9 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Cisco Systems AIRCAP3702IAK9, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Cisco Systems AIRCAP3702IAK9.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Cisco Systems AIRCAP3702IAK9. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Cisco Systems AIRCAP3702IAK9 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
