Manuel d'utilisation / d'entretien du produit 1000 du fabricant CBM
Aller à la page of 226
.
— i — Manufacturer’ s Name : Japan CBM Corporation Manufacturer’ s Address : CBM Bldg., 5-68-10, Nakano, Nakano-ku T okyo, 164-0001, Japan Declare the Product Product Name Line Thermal Printer Model Number(s) CBM1000 Series (CBM1000RF/PF) (S.No.
— ii — IMPOR T ANT SAFETY INSTRUCTIONS • Read all of these instructions and save them for future reference. • Follow all warnings and instructions marked on the product. • Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners.
— iii — WICHTIGE SICHERHEITSANWEISUNGEN • Lesen Sie die nachfolgenden Anweisungen sorgfältig durch und bewahren Sie sie auf. • Befolgen Sie alle auf dem Drucker vermerkten Hinweise und Anweisungen. V or dem Reinigen grundsätzlich Stecker aus der Steckdose ziehen.
— iv — IMPORT ANT : This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications.
— v — GENERAL PRECAUTIONS • Prior to using the CBM1000 Printer , be sure to read this User’ s Manual thoroughly . Please keep it handy so that you can refer to it whenever necessary . • The information contained herein may be changed without prior notice.
— vi — SAFETY PRECAUTIONS — WHICH SHOULD BE STRICTL Y OBSER VED In order to help prevent safety hazards to operators or any other persons and damages to property , special warning symbols are used in this User’ s Manual to indicate important items to be strictly observed.
— vii — W ARNING ● Never handle the CBM1000 Printer in the manners descried below; otherwise, it may be damaged, get out of order or overheated, possibly causing smoke, fire or electric shock. If the printer is damaged or breaks down, be sure to turn off the power , disconnect the power plug from the wall outlet, and contact your CBM dealer .
— viii — PRECAUTIONS FOR INST ALLA TION • Do not use or store the CBM1000 Printer in a place exposed to heat of fire, moisture or direct sunlight, or in a place where the prescribed operating te.
— ix — PRECAUTIONS FOR HANDLING Obser ve the following precautions to use the CBM1000 Printer cor r ectly and avoid troubles from occurring. • Do not use any other power supply than the specified AC adapter . • Do not allow the printer to start printing when there is no recording paper installed.
— x — HOT AREA: Be careful not to touch this area to avoid burns as it becomes HOT . In the position indicated below , a label is provided to alert your attention. Read the cautionary information on it, and handle the printer properly . This label alerts you to the print head as it becames HOT , and if you touch it, you may get burnt.
— xi — DAIL Y MAINTENANCE • Prior to star t maintenance work, be sure to turn off the printer . • When cleaning the platen, use a cotton swab applied with ethyl alcohol and wipe off stains. CAUTION: A void cleaning the print head immediately after printing is finished.
— xii — Print head DAIL Y MAINTENANCE Cleaning the print head 1 T urn off the power of the printer . 2 Open the printer cover . 3 Using a gauze impregnated with a small amount of alcohol, wipe off stains and dust on the heat-emitting surface of the head.
— xiii — THE T ABLE OF CONTENTS 1. GENERAL OUTLINE ................................................................... 1 1.1 Features ..................................................................................................... 1 1.2 Unpacking .
— xiv — 6. P ARALLEL INTERF ACE ............................................................. 25 6.1 Bidirectional Parallel Interface (IEEE1284) ............................................ 25 6.1.1 Compatibility Mode (Host → Printer communication : Centronics compliant) .
— xv — 11. CHARACTER CODES T ABLE ................................................ 139 11.1 Code page ............................................................................................ 139 11.1.1 Codepage 00H to 7FH & PC437 (USA, European Standard) .
— xvi — INHAL T 4. BETRIEB .................................................................................. 178 4.1 Anschließen des Netzteils und Netzkabels ......................................... 178 4.2 Anschließen der Schnittstellenkabel .
— xvii — 7. SERIELLE SCHNITTSTELLE ................................................... 200 7.1 T echnische Daten .................................................................................. 200 7.2 Belegung der Anschlußstifte ..............
— 1 — 1. GENERAL OUTLINE The CBM1000 is a compact-sized, line thermal printer developed for a variety of applications. It has abundant built-in features, and can be used as a data communication terminal, pos terminal, kitchen terminal and for other applications.
— 2 — 1.2 Unpacking When unpacking the printer , confirm that the following are provided: • Printer ............................................................................................ 1 unit • Partition (For 58 mm wide paper roll) ...
— 3 — 2. BASIC SPECIFICA TIONS 2.1 Model Classification The printer models are classified by the following designation method: CBM1000 - R F 120 S Model Name Power supply S: Standard type (Power s.
— 4 — 2.2 Basic Specifications Model CBM1000-RF120S/A CBM1000-RF230S/A CBM1000-RF024D Item CBM1000-PF120S/A CBM1000-PF230S/A CBM1000-PF024D Print method Line thermal dot print method Print width 7.
— 5 — 2.3 Print Paper Specifications 2.3.1 Recommended Paper • T ype: Heat sensitive paper • Paper width: 80 + 0/– 1 mm; 58 + 0/– 1 mm • Paper thickness: 65 ± 5 µm • Roll diameter: .
— 6 — 2.3.2 Print Position and Barcode Printing Roll paper width 80 mm provided: Paper width 80 mm applies to printing area 72 mm (576 dots), and both left and right margins each ca.
— 7 — 2.3.3 Cutter Position Manual cutting position Auto cutting position Top print line Paper feed direction Approx. 13 mm Approx. 27 mm.
— 8 — 3. OUTER APPEARANCE AND COMPONENT P AR TS 3.1 CBM1000S Power switch Printer cover Ejector Top cover Power box POWER lamp ERROR lamp FEED switch Drawer Kick-Out Connector Grounding terminal I.
— 9 — 3.2 CBM1000A / CBM1000D Power switch Printer cover Ejector Top cover POWER lamp ERROR lamp FEED switch Drawer Kick-Out Connector Grounding terminal Power connector Interface connector.
— 10 — 4. OPERA TION 4.1 Connecting the AC Adapter and AC Power Cord 1 Turn off the power of the printer. 2 For the AC adapter type only: With the flat side of the AC adapter’s cable connector facing upward, insert the cable connector into the power connector on the back side of the printer.
— 11 — 1 Turn off the power of the printer. (As well as the host computer connected) 2 Orienting the interface cable terminal correctly, insert it into the interface connector. 3 Secure the cable terminal as shown below. Serial interface cable: Fasten the connector with screws.
— 12 — 1 Turn off the power of the printer. 2 Orienting the Drawer Kick-Out Cable Connector correctly, insert it into the Drawer Kick-Out Connector on the back of the printer. 3 Fasten the ground wire to the ground connector on the printer with a screw.
— 13 — 1 Turn on the printer. 2 Push the ejector in the direction shown to unlock the printer cover. 3 Placing your hands on both sides of the printer cover, open it until it comes to a stop. 4.4 Setting / Replacing Paper Rolls 4 Check the winding direction of the paper roll, and then place it into the paper roll holder correctly.
— 14 — 6 Remove an excess length of paper with the tear bar. (Manual cutter) CAUTION: • Always use the specified types of paper roll. • Use of other types of paper roll may not be able to guarantee the specified print quality or service life of the printer .
— 15 — 1 Open the printer cover. 2 Push the sensor knob in the direction of arrow 1 to disengage its claw (Or unlock the sensor unit), and then adjust the sensor unit to a desired paper remaining position within the range shown by arrow 2.
— 16 — 1 Turn off the power of the printer. 2 Open the printer cover. 3 Fit the partition supplied into the position shown. 4 Refer to “5. SETTING DIP SWITCHES”, change a DIP switch to the setting for using 58 mm wide paper rolls. 4.6 Using 58 mm Wide Paper Rolls Partition 1 Turn off the power of the printer.
— 17 — 1 Turn off the power of the printer. 2 Open the printer cover. 3 Wipe off stains, such as dust and the like, on the heating element of the head using a cotton swab impregnated with ethyl alcohol. 4.8 Cleaning the Print Head CAUTION: The print head has become hot immediately after printing.
— 18 — POWER ERROR FEED 4.9 Operation Panel and Error Indication POWER lamp (Green) Lights when the power is turned on. It blinks when a memory check error has occurred. ERROR lamp (Red) Lights or blinks to show different error states. It also blinks while the printer is waiting for a macro to be executed.
— 19 — Description of errors Cover open: When you open the printer cover , the cover open sensor is activated, causing the ERROR LED to light and the printing operation to stop. Head overheat: T o protect the print head from being overheated, the head temperature sensor is activated if the head temperature rises over approx.
— 20 — Starting hexadecimal dump 1 Open the top cover. 2 While pressing the FEED switch, turn on the power of the printer “ ➀ ”. 3 When you close the cover “ ➁ ”, a message “Hexadecimal Dump” is printed on paper, and then the data received afterward is printed in hexadecimal numbers and the corresponding characters.
— 21 — 1 Turn off the power of the printer. 2 Open the printer cover. 3 Remove the paper roll. 4 While pulling the tab of the DIP switch cover (To unlock it), lift out the cover.
— 22 — No. Function ON OFF Factory setting 1 Auto cutter A vailable Not available ON 2 Print mode High-quality High-speed OFF 3 Paper width 58 mm 80 mm OFF 4 Print columns * 42(80 mm) columns 48(8.
— 23 — Selection of Character Code tables (DIP switch 2) No. 1234 Code page Codepage PC437 (USA, European Standard) OFF OFF OFF OFF Codepage Katakana (Japanese) ON OFF OFF OFF Codepage PC850 (Mult.
— 24 — DIP switch 3 No. Function ON OFF Factory setting 1 Bit length 7 bits 8 bits OFF 2 Parity A vailable Not available OFF 3 Odd /Even Even number Odd number OFF 4 Communication mode XON/XOFF DTR/DSR OFF DIP switch 4 No. Function ON OFF Factory setting 1 Baud rate See the table below .
— 25 — 6. P ARALLEL INTERF ACE 6.1 Bidirectional Parallel Interface (IEEE1284) 6.1.1 Compatibility Mode (Host → Printer communication : Centronics compliant) • General description This printer provides Compatibility Mode, which specifies the Centronics interface conventionally used for a wide variety of applications.
— 26 — 6.1.3 Connector Pin Configuration Applicable connectors Printer side: 57LE-40360 (Amphenol) or equivalent Cable side: 57-30360 (Amphenol) or equivalent Pin Source Compatibility Mode Nibble .
— 27 — CAUTION: • The first letter “n” of each signal name indicates that the signal is active “L”. • If any one of the above signals is not available, bidirectional communication cannot be accomplished.
— 28 — 6.2.2 Electrical Characteristics Input signal level (STB, DA T A 1-8) All the input signals are at the C-MOS level. “HIGH” level: 4.0 V minimum “LOW” level: 0.9 V maximum Output signal level All the output signals are at the C-MOS level.
— 29 — 6.2.3 T iming Chart (Compatibility Mode) Data input and print timing 6.2.4 Data Reception Control When the Busy signal is at “LOW”, the printer can receive data from the host computer , but when at “HIGH”, data reception is not possible.
— 30 — 7. SERIAL INTERF ACE 7.1 Specifications (1) Synchronizing system Asynchronous (2) Baud rate 2400, 4800, 9600, or 19200 bps (User selectable) (3) Configuration of one word Start bit: 1-bit D.
— 31 — 7.2 Connector Pin Configuration No. Signal name Input/output Function 1 FG — Grounding for safety 2 TD Output T ransferred data 3 RD Input Received data 4 RTS Output Same as DTR 6 DSR Inp.
— 32 — 7.3 Description of Input and Output Signals 7.3.1 Input and Output Signals (1) RD This is a serial reception data signal. When a framing error , overrun error or parity error occurs, the data containing the error is printed as a “?”. (2) DTR, RTS When this signal is Ready , you can write data or commands into the input buffer .
— 33 — 7.3.2 Error Detection Detection of parity errors, framing errors, and overrun errors is provided with this printer . When an error is detected, the data containing the error is stored in the buffer as a “?”. (1) Framing error If a space state is detected at the timing of stop bit detection, this indicates that an error has occurred.
— 34 — 7.3.5 Electrical Characteristics RS-232C circuit Input (RD, DSR, INIT) Equivalent to MAX232 [Printer Side] [Host Side] Equivalent to MAX232 Output (DTR, TD, R TS) [Printer Side] [Host Side].
— 35 — 8. DRA WER KICK-OUT CONNECTOR AND POWER CONNECTOR 8.1 Specifications of Drawer Kick-Out Connector 8.1.1 Drawer Kick-Out drive signal A pulse specified by ESC p is output.
— 36 — 8.1.4 Drive Circuit 8.2 Specifications of the Power Connector The following shows the power connector from the dedicated AC adapter . Pin configuration of Power connector (Pin number and fu.
— 37 — 9. MAINTENANCE AND SER VICE For the information on maintenance and service, please contact your CBM dealer or at the following addresses: Northern America Other Areas CBM America Corporatio.
— 38 — 1 HT Horizontal tab S.P . <09>H 42 2 LF Printing and paper feed S.P . <0A>H 43 3 CR Back to printing S.P . <0D>H 44 4F F Printing in P AGE MODE and returning to P <0C>H 45 ST ANDARD MODE 5 CAN Canceling print data in P AGE MODE P <18>H 46 6 DLE EOT Sending status in real-time S.
— 39 — No. Command Function Mode Code Page In the Mode column: S = ST ANDARD MODE, P = P AGE MODE * shows the command affected by GS P . 30 ESC T Selecting the character printing direction P <1.
— 40 — Command relative to NV memory <1C>H<67>H<31> <m>H<a1>H<a2>H 64 FS g1 W riting data into the download user NV memor y S <a3>H<a4>H<nL>H 129 <nH>H[<d>]nL+ (nH × 256) <1C>H<67>H<32>H 65 FS g2 Reading data from the download user NV memory S.
— 41 — 10.2 Command Details 10.2.1 Descriptions of Each Item XXXX [Function] The name of a command. [Code] The string of codes comprising the command is represented by < >H for hexadecimal numbers, < >B for binary numbers, and < > for decimal numbers, [ ] k denotes the number of repetition of “k” times.
— 42 — 10.2.2 Command Details HT [Function] Horizontal tab [Code] <09>H [Outline] Shifts the printing position to the next horizontal tab position. • Ignored when the next horizontal tab position has not been set. [Caution] • The horizontal tab position is set by ESC D.
— 43 — LF [Function] Printing and paper feed [Code] <0A>H [Outline] Prints data inside the print buffer and feeds paper based on the line feed amount having been set.
— 44 — CR [Function] Back to printing [Code] <0D>H [Outline] 1) When DSW1-5 is OFF: This command is ignored. 2) When DSW1-5 is ON: With data held inside the internal print buffer , printing and line feed are performed. Without data inside the internal print buffer , however , only line feed is performed.
— 45 — FF [Function] Printing in P AGE MODE and returning to ST ANDARD MODE [Code] <0C>H [Outline] Executes a batch printout of the data mapped in the entire print area, and then returns to ST ANDARD MODE. [Caution] • All mapped data is erased after printout.
— 46 — CAN [Function] Canceling print data in P AGE MODE [Code] <18>H [Outline] Erases all data contained in the currently effective print area in P AGE MODE.
— 47 — DLE EOT n [Function] Sending status in real-time [Code] <10>H<04>H<n> [Range] 1 n 4 [Outline] Sends in real-time the status specified by “n”.
— 48 — (1) Printer status (When n = 1 is specified) Bit Status Hex. Decimal 0 Unused 00 0 1 Unused 02 2 Status of pin 3 of Drawer Kick-Out 00 0 Connector = L 2 Status of pin 3 of Drawer Kick-Out 0.
— 49 — (3) Status caused by an error (when n = 3 is specified) Bit Status Hex. Decimal 0 Unused 00 0 1 Unused 02 2 2 Undefined — — 3 Auto cutter error not occurred 00 0 Auto cutter error occur.
— 50 — DLE ENQ n [Function] Real-time request to printer [Code] <10>H<05>H<n> [Range] 1 n 2 [Outline] The printer responds in real-time to the request that the host specifies with number “n”. n = 1: After recovering from an error , the printer resumes printing from the beginning of the line where the error occurred.
— 51 — DLE DC4 nmt [Function] Outputting specified pulse in real-time. [Code] <10>H<14>H<n><m><t> [Range] n=1, m=0,1 1 t 8 [Outline] A signal specified with “t” is output to the connector pin specified with “m”.
— 52 — ESC FF [Function] Printing data in P AGE MODE [Code] <1B>H<0C>H [Outline] Executes a batch printout of the data mapped in the entire print area in P AGE MODE. [Caution] • This command is only effective when P AGE MODE is selected.
— 53 — ESC SP n [Function] Setting the right spacing of the character [Code] <1B>H<20>H<n> [Range] 0 n 255 [Outline] Sets the right spacing of character to [n × basic calculation pitch] inches. [Caution] • If the horizontal magnification of character is 2 or more, the right spacing increases with the magnification.
— 54 — [Sample Program] [Print Results] AAAAA ← 0-dot space AAAA A ← 1-dot space AAAAA ← 12-dots space LPRINT CHR$(&H1B) + “ ” + CHR$(0) ; LPRINT “AAAAA” + CHR$.
— 55 — ESC ! n [Function] Collectively specifying the printing mode [Code] <1B>H<21>H<n> [Range] 0 n 255 [Outline] Printing mode is assigned.
— 56 — [Sample Program] [Print Results] Font A Font B Font A + Emphasis Font B + Emphasis + Quadruple + Underline Font A + Underline Font A + Double Width Font A + Double Height ∨∨ ∨ LPRINT .
— 57 — ESC $ n1 n2 [Function] Specifying the absolute positions [Code] <1B>H<24>H<n1><n2> [Range] 0 n1 255 0 n2 1 [Outline] The printing start position is specified with the number of dots (1/203 inch unit) from the beginning of a line.
— 58 — [Sample Program] [Print Results] Relative Position Specified Absolute Position Specified ↓↓ ↓ AB ↓ C BA 0 50 100 .
— 59 — ESC % n [Function] Specifying/Canceling download character set [Code] <1B>H<25>H<n> [Range] 0 n 255 [Outline] Specifying/canceling download characters.
— 60 — ESC & s n m [a [p] s × a] m – n + 1 [Function] Defining the download characters [Code] <1B>H<26>H<s>H<n><m>[<a><p1><p2> ⋅ ⋅ <ps.
— 61 — [Example] Create each data bit by setting “1” for a printed dot and “0” for an unprinted dot. [Sample Program] Refer to Sample Program and Print Results for ESC % on page 59.
— 62 — ESC * m n1 n2 [ d ] k [Function] Specifying the bit image mode [Code] <1B>H<2A>H<m><n1><n2> [<d>] k [Range] m= 0, 1, 32, 33 0 n1 255 0 n2 3 0 d 255 k = n.
— 63 — [Sample Program] [Print Results] ← 8-dots single density ← 8-dots double density ← 24-dots single density ← 24-dots double density LPRINT CHR$(&H1B) + .
— 64 — ESC – n [Function] Specifying/Canceling underline [Code] <1B>H<2D>H<n> [Range] 0 n 2 48 n 50 [Outline] Specifying/canceling an underline.
— 65 — ESC 2 [Function] Specifying 1/6-inch line feed rate [Code] <1B>H<32>H [Outline] The line feed rate per line is specified by 1/6 inch. [Caution] Line feed rate can be specified respectively for both ST ANDARD MODE and P AGE MODE.
— 66 — ESC 3 n [Function] Setting line feed rate of minimum pitch [Code] <1B>H<33>H<n> [Range] 0 n 255 [Outline] Sets the line feed width per line to [n × basic calculation pitch] inches. [Caution] The line feed width can be set separately for the ST ANDARD and P AGE MODES.
— 67 — ESC = n [Function] Data input control [Code] <1B>H<3D>H<n> [Range] 0 n 255 [Outline] Selecting equipment for which data input from the host is valid.
— 68 — ESC ? n [Function] Deleting download characters [Code] <1B>H<3F>H<n> [Range] 32 n 126 [Outline] Deletes the downloaded characters of specified code. [Caution] • The character “n” indicates the character code used to delete the defined pattern.
— 69 — ESC @ [Function] Initializing the printer [Code] <1B>H<40>H [Outline] Clears data stored in the print buffer and brings various settings to the initial state (Default state). [Caution] • The settings of DIP switches are not read again.
— 70 — ESC D { n } k NUL [Function] Setting horizontal tab position [Code] <1B>H<44>H [<n>] k<00> [Range] 1 n 255 0 k 32 [Outline] Specifying a horizontal tab position. • “n” indicates the number of columns from the beginning to the horizontal tab position.
— 71 — ESC E n [Function] Specifying/Canceling Emphasis Printing [Code] <1B>H<45>H<n> [Range] 0 n 255 [Outline] Specifying/canceling the emphasized characters.
— 72 — ESC G n [Function] Specifying/Canceling Double strike printing [Code] <1B>H<47>H<n> [Range] 0 n 255 [Outline] Specifying/canceling the double strike printing. • “n” is valid only for the lowest bit (n0). • Control by “n” is shown as follows.
— 73 — ESC J n [Function] Printing and feeding paper in minimum pitch [Code] <1B>H<4A>H<n> [Range] 0 n 255 [Outline] Prints the data held in the print buffer and feeds paper by [n × basic calculation pitch] inches. The beginning of the line is taken as the next print start position.
— 74 — ESC L [Function] Selecting P AGE MODE [Code] <1B>H<4C>H [Outline] Switches from ST ANDARD MODE to P AGE MODE. [Caution] • This command is only effective if it entered at the beginning of a line. • This command is not effective if it is entered when in P AGE MODE.
— 75 — ESC M n [Function] Selection of character fonts [Code] <1B>H<4D>H<n> [Definition value] n=0, 1, 48, 49 [Outline] Selects character fonts.
— 76 — ESC R n [Function] Selecting the international character set [Code] <1B>H<52>H<n> [Range] 0 n 10 [Outline] Depending on the value of “n”, one of the following character sets is specified; n Character Set 0 U.S.A. 1 France 2 Germany 3 U.
— 77 — ESC S [Function] Selecting ST ANDARD MODE [Code] <1B>H<53>H [Outline] Switches from P AGE MODE to ST ANDARD MODE. [Caution] • This command is only effective if it is entered when in P AGE MODE. • Any data mapped in P AGE MODE is erased.
— 78 — ESC T n [Function] Selecting the character printing direction in P AGE MODE [Code] <1B>H<54>H<n> [Range] 0 n 3 48 n 51 [Outline] Selects the direction and start point of character printing in P AGE MODE.
— 79 — ESC V n [Function] Specifying/Canceling 90°-right-turned characters [Code] <1B>H<56>H<n> [Range] n = 0, 1, 48, 49 [Outline] Specifying/canceling 90°-right- turned characters.
— 80 — ESC W xL xH yL yH dxL dxH dyL dyH [Function] Defining the print area in P AGE MODE [Code] <1B>H<57>H<xL><xH><yL><yH><dxL><dxH><dyL><.
— 81 — • The figure below illustrates the print area, where X = horizontal start point, Y=vertical start point, Dx=horizontal length, and Dy=vertical length. The printable area for this printer is approximately 72.070 mm (576/203 inches) horizontally and 1207.
— 82 — ESC nL nH [Function] Specifying the relative position [Code] <1B>H<5C>H<nL><nH> [Range] 0 nL 255 0 nH 255 [Outline] This command specifies the next print start position in a relative position with respect to the current position.
— 83 — ESC a n [Function] Aligning the characters [Code] <1B>H<61>H<n> [Range] 0 n 2 48 n 50 [Outline] All the printed data within one line are aligned in the specified position.
— 84 — ESC c 3 n [Function] Selecting the Paper Sensor valid for a paper end signal output [Code] <1B>H<63>H<33>H<n> [Range] 0 n 255 [Outline] This command selects by which Paper Sensor a paper end signal should be output.
— 85 — ESC c 4 n [Function] Selecting the Paper Near -end Sensor valid for print stop [Code] <1B>H<63>H<34>H<n> [Range] 0 n 255 [Outline] This command selects the Paper Near -end Sensor which helps to stop printing when the paper supply almost runs out.
— 86 — ESC c 5 n [Function] Enabling/Disabling the panel switches [Code] <1B>H<63>H<35>H<n> [Range] 0 n 255 [Outline] Enabling/disabling the FEED switch.
— 87 — ESC d n [Function] Printing and feeding the paper by “n” lines [Code] <1B>H<64>H<n> [Range] 0 n 255 [Outline] Prints data in the print buffer and feeds paper by “n” lines. • Specified lines do not remain. • The beginning of the line is specified as the next print start position.
— 88 — ESC p m n1 n2 [Function] Generating the specified pulses [Code] <1B>H<70>H<m><n1><n2> [Range] m = 0, 1, 48, 49 0 n1 255 0 n2 255 [Outline] The signals specified by “n1” and “n2” are output to the connector pin specified by “m”.
— 89 — ESC t n [Function] Selecting the character code table [Code] <1B>H<74>H<n> [Range] 0 n 9, n = 255 [Outline] Selecting the character code table: The character code table is selected based on the value of “n”.
— 90 — ESC { n [Function] Specifying/Canceling the inverted characters [Code] <1B>H<7B>H<n> [Range] 0 n 255 [Outline] Specifying/canceling inverted characters. • “n” is valid only for the lowest bit. n0 Condition 0 Canceling inverted characters.
— 91 — GS ! n [Function] Specifying the character size [Code] <1D>H<21>H<n> [Range] 0 n 255, where: 1 vertical magnification 8, 1 horizontal magnification 8 [Outline] Specifies the character size (V ertical and horizontal magnification).
— 92 — • If characters of different vertical magnification are contained in a line, the baseline of each character is lined up. • Horizontal and vertical magnification can also be specified/ canceled by ESC !. The ESC ! or GS ! command, whichever is handled last, becomes effective.
— 93 — GS $ nL nH [Function] Specifying the absolute vertical position of characters in P AGE MODE [Code] <1D>H<24>H<nL><nH> [Range] 0 nL 255 0 nH 255 [Outline] This comman.
— 94 — GS * n1 n2 [ d ] n1 × n2 × 8 [Function] Defining the download bit image [Code] <1D>H<2A>H<n1><n2> [< d >] n1 × n2 × 8 [Range] 1 n1 255 1 n2 48 n1 × n2 1536 0 d 255 [Outline] Defines download bit images of the number of dots specified by n1 and n2.
— 95 — [Sample Program] [Print Results] ← QUADRUPLE MODE ← NORMAL MODE ← DOUBLE WIDTH MODE ← DOUBLE HEIGHT MODE GOSUB IMG LPRINT CHR$(&H1D) + “/” + CHR$(0);.
— 96 — GS (A pL pH n m [Function] Execution of test printing [Code] <1D>H<28>H<41>H<pL><pH><n><m> [Definition] (pL+(pH × 256))=2 (pL=2, pH=0) 0 n 2, 48 n 50 1 m 3, 49 m 51 [Outline] Specified test printing will be executed.
— 97 — GS / m [Function] Printing the downloaded bit image [Code] <1D>H<2F>H<m> [Range] 0 m 3 48 m 51 [Outline] Prints downloaded bit image in a mode specified by “m”.
— 98 — GS : [Function] Starting/Ending macro definition [Code] <1D>H<3A>H [Outline] Specifying starting/ending macro definition. Reception of this command during macro definition signifies ending the macro definition. [Caution] Maximum content available for macro definition is 2048 bytes.
— 99 — GS B n [Function] Specifying/Canceling the black/white inverted printing [Code] <1D>H<42>H<n> [Range] 0 n 255 [Outline] This command specifies or cancels the black/white inverted printing. n0 Function 0 The black/white inverted printing is canceled.
— 100 — GS H n [Function] Selecting of printing position of HRI characters [Code] <1D>H<48>H<n> [Range] 0 n 3 48 n 51 [Outline] Selecting printing position of HRI characters in printing bar codes. • “n” means the followings.
— 101 — Printed above and below [Print Results] No HRI characters Printed above Printed below.
— 102 — GS I n [Function] Sending the printer ID [Code] <1D>H<49>H<n> [Range] 1 n 3 49 n 51 [Outline] Sends the specified printer ID. n T ype of printer ID Specification V alue (Hex.) 1,49 Model ID CBM1000 30 2,50 T ype ID Refer to table “T ype ID” below 3,51 ROM version ID As per ROM version T ype ID Bit Meaning Hex.
— 103 — GS L nL nH [Function] Setting the left margin [Code] <1D>H<4C>H<nL><nH> [Range] 0 nL 255 0 nH 255 [Outline] This command sets the left margin specified by nL and nH. The value of the left margin is [(nL + nH × 256) × basic calculation pitch] inches.
— 104 — • When mapping non-character data (Bit image, downloaded bit image, or bar code), if the print area specified is narrower than 9-bits, only the line for that data is handled as follows: (1) The print area is extended toward the left (So, the left margin is decreased) until it is 9-dot wide, but not wider than the printable area.
— 105 — GS P x y [Function] Specifying the basic calculation pitch [Code] <1D>H<50>H<x><y> [Range] 0 x 255 0 y 255 [Outline] This command sets the horizontal basic calculation pitch to approx. 25.4/x mm (1/x inches), and the vertical basic calculation pitch to approx.
— 106 — GS V m ......... (1) GS V m n ..... (2) [Function] Cutting the paper [Code] (1) <1D>H<56>H<m> (2) <1D>H<56>H<m><n> [Range] (1) m = 1, m = 49 (2) m = 66 0 n 255 [Outline] Performs the specified paper cutting.
— 107 — GS W nL nH [Function] Setting the print area width [Code] <1D>H<57>H<nL><nH> [Range] 0 nL 255 0 nH 255 [Outline] Sets the print area width specified by nL and nH. • The print area width will be [(nL + nH × 256) × basic calculation pitch] inches.
— 108 — (2) If a sufficient area cannot be provided as a result of step (1), the print area is extended toward the left (So, the left margin is decreased). (3) If a sufficient area cannot be provided as a result of step (2), the right spacing is trimmed.
— 109 — GS nL nH [Function] Specifying the relative vertical position of a character in P AGE MODE [Code] <1D>H<5C>H<nL><nH> [Range] 0 nL 255 0 nH 255 [Outline] This comma.
— 110 — GS ^ n1 n2 n3 [Function] Executing the macro [Code] <1D>H<5E>H<n1><n2><n3> [Range] 0 n1 255 0 n2 255 0 n3 1 [Outline] Executing contents defined in macro. n1 : The number of times of macro execution n2 : W aiting time on macro execution W aiting time of n2 × 100 msec is given for every execution.
— 111 — GS a n [Function] Enabling/Disabling ASB (Automatic Status Back) [Code] <1D>H<61>H<n> [Range] 0 n 255 [Outline] This command selects the status item to be addressed by ASB (Automatic Status Back.) Bit Status item addressed by ASB Hex.
— 112 — (1) 1st byte (Printer information) Bit Status Hex. Decimal 0 Unused 00 0 1 Unused 00 0 2 Status of pin 3 of Drawer Kick-Out Connector = “L” 00 0 Status of pin 3 of Drawer Kick-Out Conn.
— 113 — (4) 4th byte (Paper Sensor information) Bit Status Hex Decimal 0 Undefined — — 1 Undefined — — 2 Undefined — — 3 Undefined — — 4 Unused 00 0 5 Undefined — — 6 Undefined.
— 114 — GS f n [Function] Selecting the font of HRI characters [Code] <1D>H<66>H<n> [Range] n = 0, 1 [Outline] Selecting the font of HRI characters in printing bar code.
— 115 — GS h n [Function] Specifying the height of the bar code [Code] <1D>H<68>H<n> [Range] 1 n 255 [Outline] Selecting bar code height. “n” denotes the number of dots in the vertical direction. [Default] n = 162 [Sample Program] Refer to Sample Program and Print Results for GS w on page 107.
— 116 — GS k m [d1 ..... dk] NUL GS k m n [d1 ...... dn] [Function] Printing the bar code [Code] (1) <1D>H<6B>H<m> [d1.....dk] NUL (2) <1D>H<6B>H<m><n> [d1....dn] [Range] (1) 0 m 6 The definitions of “k” and “d” vary with the bar code system.
— 117 — [Caution] For (1): • This command ends with a NUL code. • For UPC-A or UPC-E, the bar code is printed when 12 bytes of bar code data have been entered, and the subsequent data is handled as normal data.
— 118 — For P AGE MODE: • This command only maps the bar code, without performing a printout. After the bar code is mapped, the dot next to the last data item of the bar code is taken as the start position for the next data mapping.
— 119 — [Description of Bar Codes] <For print examples, refer to page 123.> UPC-A This bar code, consisting of numerals only , has a fixed length of 12 columns; a 11-column number entered from the host or application software plus a check digit (12th column) automatically calculated inside the printer .
— 120 — CODABAR (NW -7) This bar code, consisting of alphanumerics, has a variable length of columns. A vailable characters include “0 1 2 3 4 5 6 7 8 9 A B C D $ + – . / : ”. A start/stop code is required; any one of A, B, C, and D is used.
— 121 — CODE128 This bar code consists of 103 bar code characters and three code sets, enabling 128 ASCII code characters to be printed. It has a variable length of columns. • Code set A ASCII characters 00H - 5FH can be represented. • Code set B ASCII characters 20H - 7FH can be represented.
— 122 — Special characters Hex. ASCII Code set A Code set B Code set C 7B53 { S SHIFT SHIFT –N/A 7B41 { A –N/A CODE A CODE A 7B42 { B CODE B –N/A CODE B 7B43 { C CODE C CODE C –N/A 7B31 { .
— 123 — [Description of Bar Codes] UPC-A, UPC-E, JAN-13 (EAN), JAN-8 (EAN), CODE39, ITF , CODABAR, CODE93, CODE128 T ype Print Sample Outline of Symbol Printing is done according to bar code type, number of print columns, bar code height, width (Magnification), availability of HRI character , and bar code data.
— 124 — GS r n [Function] Sending status [Code] <1D>H<72>H<n> [Range] 1 n 2 49 n 50 [Outline] Sends the specified status to the host. n = 1, 49: Sends the Paper Sensor status. n = 2, 50: Sends the Drawer Kick-Out Connector status.
— 125 — • Drawer Kick-Out Connector status (n = 2, 50) Bit Status Hex. Decimal 0 Status of pin 3 of Drawer Kick Connector = “L” 00 0 Status of pin 3 of Drawer Kick Connector = “H” 01 1 1.
— 126 — GS v0 m xL xH yL yH d1...dk [Function] Printing of raster bit image [Code] <1D>H<76>H<30>H<m><xL><xH><yL><yH> [<d>] k [Range] 0 m 3, 4.
— 127 — • If this command is executed during macro definition, the macro definition is suspended, and the processing of the command starts. The macro is left undefined. • “d” denotes defined data. Dots to be printed are specified as “1”, and those not to be printed as “0”.
— 128 — GS w n [Function] Specifying the horizontal size (Magnification) of bar code [Code] <1D>H<77>H<n> [Range] 2 n 6 [Outline] Selecting bar code width.
— 129 — FS g1 m a1 a2 a3 a4 nL nH d1…dk [Function] W riting data into the download user NV memory [Code] <1C>H<67>H<31><m>H<a1>H<a2>H<a3>H<a4>H &l.
— 130 — [Caution] • Because frequent writing in the non-volatile memory can destroy the memory , the writing command (FS g1) should be used less than 10 times a day . • It may happen that the printer becomes BUSY during the process of writing data into the non-volatile memory while this command is executed.
— 131 — FS g2 m a1 a2 a3 a4 nL nH [Function] Reading data from the download user NV memory [Code] <1C>H<67>H<32>H<m>H<a1>H<a2>H<a3>H<a4>H <nL>.
— 132 — • When the XON/XOFF control is selected, all the codes are sent continuously without verifying that the host can receive the data. Data that has been sent is always continuous except for the XOFF code.
— 133 — F S p n m [Function] Printing the download NV bit images [Code] <1C>H<70>H<n><m> [Range] 1 n 255 0 m 3 48 m 51 [Outline] This command prints the download NV bit images (n) using a specified mode (m).
— 134 — • When the size of a bit image exceeds the limits of the printing area, the data within the limits of the printing area will be printed but the parts exceeding the limit will not be printed.
— 135 — F S q n [xL xH yL yH d1…dk] 1… [xL xH yL yH d1…dk] n [Function] Defining the download NV bit image [Code] <1C>H<71>H<n>H{<xL><xH><yL><yH><d1...dk>}1... {<xL><xH><yL><yH><d1.
— 136 — • If outside-defined-area arguments are processed for the second or subsequent NV bit image data groups, the processing of this command is suspended, and a writing process into the non-volatile memory starts. At this time, the NV bit image being defined becomes invalid (Undefined), but the preceding NV bit images are valid.
— 137 — [Caution] • Because frequent writing in the non-volatile memory can destroy the memory , the writing command should be used less than 10 times a day . • Just after the completion of the writing operation into the non- volatile memory , the printer hardware will be reset.
— 138 — (yL + yH × 256) × 8dots = 768dots [Example] When xL =64, xH = 0, yL = 96, yH = 0 (xL + xH × 256) × 8dots = 512dots.
— 139 — 11. CHARACTER CODES T ABLE 11.1 Code Page 11.1.1 Codepage 00H to 7FH & PC437 (USA, European Standard).
— 140 — 11.1.2 Codepage Katakana (Japanese).
— 141 — 11.1.3 Codepage PC850 (Multilingual).
— 142 — 11.1.4 Codepage PC860 (Portuguese).
— 143 — 11.1.5 Codepage PC863 (Canadian-French).
— 144 — 11.1.6 Codepage PC865 (Nordic).
— 145 — 11.1.7 Codepage PC852 (Eastern Europe).
— 146 — 11.1.8 Codepage PC866 (Russian).
— 147 — 11.1.9 Codepage PC857 (T urkish).
— 148 — 11.1.10 Windows Codepage.
— 149 — 11.2 International Character Codes T able Country U.S.A. France Germany U.K. Denmark 1 Sweden Italy Spain 1 Japan Norway Denmark 2 Spain 2 Latin America Korea.
—150 — —150 — 12. APPENDIX 1. P AGE MODE 12.1. Overview The printer has two print modes: ST ANDARD and P AGE. In ST ANDARD MODE, the printer prints or feeds paper each time it receives a print or paper feed command.
—151 — 12.2 Mapping of print data in the print area Print data is mapped in the print area as follows: (1) The print area is set by ESC W . When the printer has finished all of the print and paper.
—152 — —152 — A Baseline Point A Print Area Mapping Direction 24-3 dx,dy x0,y0 3 A Baseline Point B Point B Double Height Character Downloaded Bit Image (HRI Characters) Bar Code GS k m 24-3 2.
—153 — 12.2.1 Example of the Use of P AGE MODE The following explains specific uses of P AGE MODE. When in P AGE MODE, the commands are typically sent from the host to the printer in the following sequence: (1) An ESC L puts the printer in P AGE MODE.
—154 — —154 — In Figure 1-1, a line feed occurs between “lesson” and “T est 1” because the space “ “ next to “lesson” dose not fit in the horizontal range of the 200 × 400-pitch print area. The line feed width conforms to the value specified by a command such as ESC 3.
—155 — Before an FF is sent, the following program code can be added to remove part of the data. LPRINT CHR$(&H1B) + “W” + CHR$((72) + CHR$(0) + CHR$(120) + CHR$(0); LPRINT CHR$(36) + CHR$.
—156 — —156 — 13. APPENDIX 2. BIDIRECTIONAL P ARALLEL INTERF ACE 13.1 Overview The interface of the printer is a Level-1 compatible device according to IEEE-P1284.
—157 — 13.1.2 Interfacing Phases Interfacing in each communication mode is divided into several phases. In addition, there is a phase for mode initialization, as well as a phase for mode switching. Interface signals may differ in name and function for different modes and different phases.
—158 — —158 — 13.2 Negotiation 13.2.1 Overview Usually , the printer is started in Compatibility mode, which corresponds to the Centronics interface phase. When the host intends to switch to the Nibble or Byte mode, it sends a request and negotiates with the printer .
—159 — 13.2.3 Precautions 1) The Negotiation phase is triggered when the IEEE 1284 Active signal sent by the host becomes High. 2) In Compatibility mode, the time when the negotiation process begins is, as a general rule, after the host sets nStrobe to High and then the printer outputs an nAck pulse.
—160 — —160 — 13.2.4 Data Communication from Printer to Host 13.2.4.1 Nibble Mode In this mode, data is transferred between the printer and the host through the procedure described below . The steps beginning from 1) are applicable when the Negotiation phase has switched to the Host Busy Data A vailable phase.
—161 — 12) If the host selected the Reverse Idle phase and new data becomes available to be sent from the printer , the printer sets PtrClk to Low to request the host for an interrupt.
—162 — —162 — 10) When more data is to be received from the printer , the host chooses one of three status selections: 1. Setting HostBusy (nAutoFd) to Low and indicating that the host is ready to receive. 2. Remaining in the Host Busy Data A vailable phase.
—163 — (1) T ermination through a handshake between the host and the printer: When switching from Reverse mode to Compatibility mode, this termination method can be used if the interface is activated (IEEE 1284 Active: High) and event 22 has taken place.
—164 — —164 — 14. APPENDIX 3.IDENTIFICA TION OF SEND ST A TUS Because the status sent from the printer has certain fixed bits, it is possible to identify to which command the status belongs.
—165 — 15. APPENDIX 4. OUTLINE DRA WING 15.1 CBM1000S 145 157 190.
—166 — —166 — 15.2 CBM1000A / CBM1000D 145 114 190.
—167 — 15.3 AC Adapter (31AD).
—168 — —168 — 16. APPENDIX 5. BLOCK DIAGRAM FLASH ROM LED FEED Switch Stepping Moter Paper Near-end Paper End Cover Switch Power Source DC 24V 1.
— 169 — GERMAN.
— 170 — ALLGEMEINE VORSICHTSMASSNAHMEN • Bevor Sie den Drucker CBM1000 verwenden, lesen Sie dieses Benutzerhandbuch gründlich. Bewahren Sie es griffbereit auf, so daß Sie darin gegebenenfalls nachschlagen können. • Die in diesem Handbuch enthaltenen Informationen können ohne vorherige Ankündigung geändert werden.
— 171 — Dieses Symbol soll Ihre Aufmerksamkeit auf wichtige Punkte lenken. Dieses Symbol soll Ihre Aufmerksamkeit auf nützliche Informationen, wie beispielsweise V erfahren, Anweisungen usw .
— 172 — W ARNUNG ● Behandeln Sie den Drucker CBM1000 niemals in der nachstehend beschriebenen W eise. Anderenfalls kann er beschädigt werden, funktionsuntüchtig werden oder über hitzen, Rauch entwickeln, und es entsteht möglicherweise ein Brand, oder es besteht die Gefahr eines elektrischen Schlags.
— 173 — VORSICHTSMASSNAHMEN FÜR DIE INST ALLA TION • Betreiben und lagern Sie den Drucker CBM1000 auf keinen Fall an Or ten, die Feuer , Feuchtigkeit oder direkter Sonneneinstrahlung ausgesetzt.
— 174 — VORSICHTSMASSNAHMEN FÜR DIE HANDHABUNG Beachten Sie die folgenden V orsichtsmaßnahmen, um den Dr ucker CBM1000 richtig zu betreiben und um zu verhindern, daß Probleme auftreten. • V erwenden Sie ausschließlich das vorgeschriebene Netzteil.
— 175 — HEISSER BEREICH: Berühren Sie den Druckkopf nicht, um V erbrennungen zu vermeiden, da er HEISS wird. Nachstehend wird ein W arnschild des Druckers beschrieben, das Sie auf eine potentielle Gefahr aufmerksam machen soll. Lesen Sie den W arnhinweis auf diesem Schild, und verhalten Sie sich im Umgang mit dem Drucker entsprechend.
— 176 — TÄGLICHE W AR TUNGSARBEITEN • Schalten Sie den Drucker unbedingt aus, bevor Sie W artungsarbeiten durchführen. • W enn Sie die W alze reinigen, verwenden Sie einen in Ethylalkohol getränkten W attebausch, um Flecken abzuwischen.
— 177 — TÄGLICHE W ARTUNGSARBEITEN Reinigen des Druckkopfs 1 Schalten Sie die Stromversorgung des Druckers aus. 2 Öfnen Sie die Druckerabdeckung. 3 V erwenden Sie Gaze, die mit etwas Alkohol benetzt ist, um Flecken und Staub auf der Seite des Druckkopfes abzuwischen, die Wärme abstrahlt.
— 178 — 4. BETRIEB 4.1 Anschließen des Netzteils und Netzkabels 1 Schalten Sie die Stromversorgung des Druckers aus. 2 Drehen Sie die flache Seite des Netzteilkabelanschlusses nach oben, und stecken Sie den Netzkabelanschluß in den Netzanschluß auf der Rückseite des Druckers.
— 179 — ACHTUNG : • V er wenden Sie ausschließlich das vorgeschriebene Netzteil. • Wenn Sie den Netzkabelanschluß des Netzteils anschließen oder abtrennen, ziehen Sie immer am Stecker und nicht am Kabel.
— 180 — 1 Schalten Sie die Stromversorgung des Druckers (Und die Stromversorgung des angeschlossenen Computers) aus. 2 Richten Sie das Schnittstellenkabel richtig aus, und schließen Sie es an die entsprechende Schnittstelle an. 3 Sichern Sie das Kabel gemäß der Darstellung weiter unten.
— 181 — 1 Schalten Sie die Stromversorgung des Druckers aus. 2 Richten Sie den Drawer Kickout- Kabelstecker richtig aus, und stecken Sie ihn in den Drawer Kickout-Stecker auf der Rückseite des Druckers. 3 Befestigen Sie den Erdungsleiter an der Erdungsklemme am Drucker mit einer Schraube.
— 182 — 1 Schalten Sie den Drucker ein. 2 Drücken Sie den Auswurfhebel in die angezeigte Richtung, um die Druckerabdeckung zu entriegeln. 3 Halten Sie die Druckerabdeckung auf beiden Seiten mit den Händen, und öffnen Sie sie bis zum Anschlag. 4.
— 183 — ACHTUNG : • V er wenden Sie stets den vorgeschriebenen Papierrollentyp. • Wenn andere Papierrollentypen verwendet werden, kann die angegebene Druckqualität möglicherweise nicht erzielt oder die Lebensdauer des Druckers reduziert werden.
— 184 — 1 Öffnen Sie die Druckerabdeckung. 2 Drücken Sie den Sensorknopf in Richtung Pfeil 1, um die Klaue auszurücken (Oder den Sensor zu entriegeln), und justieren Sie anschließend den Sensor entsprechend der gewünschten Restpapiermenge innerhalb des Bereichs, der durch Pfeil 2 angezeigt wird.
— 185 — 1 Schalten Sie die Stromversorgung des Druckers aus. 2 Öffnen Sie die Druckerabdeckung. 3 Setzen Sie die mitgelieferte Trennvorrichtung an der dargestellten Position ein.
— 186 — 1 Schalten Sie die Stromversorgung des Druckers aus. 2 Öffnen Sie die Druckerabdeckung. 3 Wischen Sie Schmutz, wie beispielsweise Staub und ähnliches, vom Heizelement des Kopfes mit Hilfe eines Wattebausches ab, der mit Ethylalkohol getränkt ist.
— 187 — POWER ERROR FEED 4.9 Bedienungsfeld und Fehleranzeige Anzeigeleuchte POWER (Grün) Diese Anzeigeleuchte leuchtet bei eingeschalteter Stromversorgung. Sie blinkt, wenn ein Speicherfehler aufgetreten ist. Anzeigeleuchte ERROR (Rot) Diese Anzeigeleuchte leuchtet oder blinkt, um unterschiedliche Fehlerzustände anzuzeigen.
— 188 — Fehlerbeschreibung Abdeckung geöffnet: W enn Sie die Druckerabdeckung öffnen, wird der Sensor aktiviert, der erkennt, wenn die Abdeckung geöffnet ist. Durch diesen Sensor werden die LED ERROR eingeschaltet und der Druckvorgang gestoppt.
— 189 — T aste FEED • W enn Sie diese T aste einmal kurz drücken, wird das Papier um eine Zeile vorgeschoben. W enn Sie die T aste länger drücken, wird das Papier kontinuierlich vorgeschoben. • W enn der Schalter gedrückt wird, während der Drucker auf die Ausführung eines Makros wartet, wird der Makro ausgeführt.
— 190 — Starten des Hexdump 1 Öffnen Sie die obere Abdeckung. 2 Halten Sie die Taste FEED gedrückt, und schalten Sie dabei die Stromversorgung des Druckers “ ➀ ” ein.
— 191 — 1 Schalten Sie die Stromversorgung des Druckers aus. 2 Öffnen Sie die Druckerabdeckung. 3 Nehmen Sie die Papierrolle heraus. 4 Ziehen Sie an der Zunge des DIP- Schalterdeckels (Um ihn zu entriegeln), und nehmen Sie anschließend den Deckel heraus.
— 192 — No. Funktion ON OFF W erkseinstellungen 1 Automatischer V erfügbar Nicht verfügbar ON Papierschneider 2 Drucken-modus Hohe-Qualität Hohe-Geschwindigkeit OFF 3 Papierbreite 58 mm 80 mm O.
— 193 — Wählen der Zeichencodetabellen (DIP-Schalter 2) No. 1234 Code seite Codeseite PC437 (USA, Europäer Standard) OFF OFF OFF OFF Codeseite Katakana (Japanisch) ON OFF OFF OFF Codeseite PC850.
— 194 — DIP-Schalter 3 No. Funktion ON OFF W erkseinstellung 1 Bitlänge 7-Bit 8-Bit OFF 2 Parität V erfügbar Nicht verfügbar OFF 3 Ungerade/Gerade Gerade Zahl Ungerade Zahl OFF 4 Kommunikationsmodus XON/XOFF DTR/DSR OFF DIP-Schalter 4 No. Funktion ON OFF W erkseinstellung 1 Baud-Rate Vgl.
— 195 — 6. P ARALLELE SCHNITTSTELLE 6.1 Bidirektionale parallele Schnittstelle (IEEE1284) 6.1.1 Kompatibilitätsmodus (Host → Druckerkommunikation: Centronics-kompatibel) • Allgemeine Beschrei.
— 196 — 6.1.3 Belegung der Anschlußstifte V erwendbare Anschlüsse Druckerseitig: 57LE-40360 (Amphenol) oder äquivalente Anschlüsse Kabelseitig: 57-30360 (Amphenol) oder äquivalente Anschlüss.
— 197 — 6.2.1 Eingangs- und Ausgangssignale Druckereingangssignale • DA T A: 8-Bit-Parallelsignal. (Aktiv im Hochpegelzustand) • nStrobe: Hinweissignal zur Unterstützung des Lesevorgangs von 8-Bit- Daten. (Aktiv im T iefpegelzustand) • nlnit: Signal zum Rücksetzen aller Druckerfunktion.
— 198 — 6.2.2 Elektrische Kenndaten Eingangssignalpegel (STB, DA T A 1-8) Alle Eingangssignale entsprechen dem C-MOS Pegel. Hochpegel: maximal 4,0 V T iefpegelzustand: maximal 0,9 V Ausgangssignalpegel Alle Ausgangssignale entsprechen dem C-MOS Pegel.
— 199 — 6.2.3 T iming-T abelle (KompatibilitätsModus) T iming von Dateneingang und Datendruck T1, T2, T3: minimal 0,5 µs T4: maximal 270 ns T5: typischerweise 2,3 µs T6: minimal 500 ms (Beim Einschalten der Stromversorgung) 6.
— 200 — 7. SERIELLE SCHNITTSTELLE 7.1 T echnische Daten (1) Systemsynchronisierung Asynchron (2) Baud-Rate 2400, 4800, 9600 oder 19200 Bit/s (V om Benutzer wählbar) (3) Konfiguration eines W or t.
— 201 — 7.2 Belegung der Anschlußstifte No. Signalname Eingang/Ausgang Funktion 1 FG — Sicherheitserdung 2 TD Ausgang Übertragene Daten 3 RD Eingang Empfangene Daten 4 RTS Ausgang Identisch mi.
— 202 — 7.3 Beschreibung der Eingangs- und Ausgangssignale 7.3.1 Eingangs- und Ausgangssignale (1) RD Hierbei handelt es sich um ein serielles Empfangsdatensignal. W enn ein DÜ- Blockfehler , Überlauffehler oder Paritätsfehler auftritt, werden die fehlerhaften Daten so geduruckt: “?”.
— 203 — (6) FG Hierbei handelt es sich um ein Massesignal. (7) GND Hierbei handelt es sich um die gemeinsame Erde von Schaltkreisen. 7.3.2 Fehlererkennung Dieser Drucker kann Paritätsfehler , DÜ-Blockfehler und Überlauffehler erkennen. W enn ein Fehler erkannt wird, werden die fehlerhaften Daten im Pufferspeicher als “?” gespeichert.
— 204 — 7.3.5 Elektrische Kenndaten RS-232C-Schaltkreis Eingang (RD, DSR, INIT) Äquivalent zu MAXIMUM232 [Druckerseitig] [Computerseitig] Äquivalent zu MAXIMUM232 Ausgang (DTR, TD, R TS) [Drucke.
— 205 — 8. DRA WER KICKOUT -ANSCHLUSS UND STROMANSCHLUSS 8.1 T echnische Daten des Drawer KickOut-Anschlusses 8.1.1 Drawer KickOut-T reibersignal Ein Impuls (ESC p) wird gesendet.
— 206 — 8.1.4 T reiberschaltung 8.2 T echnische Daten des Stromanschlusses Nachstehend ist der Stromanschluß des speziellen Netzteils dargestellt.
— 207 — 9. WAR TUNG UND KUNDENDIENST Informationen über W artung und Kundendienst erhalten Sie bei Ihrem CBM- Händler oder unter den folgenden Anschriften. Nordamerika Sonstige Länder CBM America Corporation Japan CBM Corporation Service Center Information Systems Division 365 V an Ness W ay CBM Bldg.
Information Systems Division CBM Bldg., 5-68-10, Nakano, Nakano-ku, T okyo 164-0001, Japan Head Office T el: (+81- 3) 5345-7540 Fax: (+81- 3) 5345-7541 04-991126- ×××× - ×××× - ××× .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté CBM CBM1000 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du CBM CBM1000 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation CBM CBM1000, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le CBM CBM1000 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le CBM CBM1000, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du CBM CBM1000.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le CBM CBM1000. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei CBM CBM1000 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
