Manuel d'utilisation / d'entretien du produit 2000 du fabricant Cadillac
Aller à la page of 19
2000 Cadillac D e Ville Outer Wheelhouse Sectioning 1-12 Inner Front Pillar Sectioning 1-9 Inner Center Pillar Sectioning 1-10 Outer Front Pillar Sectioning 1-2 Outer Center Pillar Sectioning 1-4 Rear.
2000 cadillac deville 1-1 Outer Front Pillar , Center Pillar and Quarter Panel Sectioning CAUTION: When performing service on or near the Supplemental Inflatable Restraint (SIR) components or the SIR wiring, the SIR system must be disabled.
Outer Front Pillar Sectioning Removal Procedure IMPORTANT: Sectioning should be performed only in the recommended areas. Failure to do so may compromise the structural integrity of the vehicle. 1. Visually inspect and restore as much of the damage as possible to factory specifications.
Installation Procedure IMPORTANT: Remove all foam prior to welding this section of the service panel. 1. Prepare mating surfaces. 2. Apply weld-through primer to mating surfaces prior to assembly. 3. Weld backing plates to vehicle at rocker. IMPORTANT: Replace hinge pillar blocks prior to welding outer panel.
Outer Center Pillar Sectioning Removal Procedure IMPORTANT: Sectioning should be performed only in the recommended areas. Failure to do so may compromise the structural integrity of the vehicle. 1. Locate an approved sectioning area in the center pillar (Fig.
Installation Procedure 1. Install sleeves on vehicle at rocker and center pillar areas using plug welds. 2. Replace hinge blocks and bolts. 3. Prepare mating surfaces. IMPORTANT: Prior to refinishing, refer to the publication GM4901M-D-2000 “GM Approved Refinish Materials” for recommended products.
1-6 2000 cadillac deville Quarter Panel Sectioning Removal Procedure The service part comes with lower quarter panel extension and taillamp pocket attached. These parts can be left on the vehicle if not damaged. Drill out factory welds on the car and service part and use the outer panel only.
2000 cadillac deville 1-7 Preparation Of Service Part 1. Cut service part in corresponding locations to fit original cut lines. Leave a gap of one-and- one-half times the metal thickness of sectioning joint (Fig. 1-9). 2. Create 100␣ mm (4␣ in) backing plate on rocker panel from unused portion of service part.
1-8 2000 cadillac deville Inner Front Pillar , Center Pillar and Rear Wheelhouse Sectioning Fig.␣ 1-11 — 2000 DeVille Inner Frame Sectioning Locations CAUTION: When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled.
2000 cadillac deville 1-9 Inner Front Pillar Sectioning Removal Procedure IMPORTANT: Sectioning should be performed only in the recommended areas. Failure to do so may compromise the structural integrity of the vehicle. 1. Visually inspect and restore as much of the damage as possible to factory specifications.
1-10 2000 cadillac deville Installation Procedure 1. Prepare mating surfaces. IMPORTANT: Prior to refinishing, refer to the publication GM4901M-D-2000 “GM Approved Refinish Materials” for recommended products. Do not combine paint systems. Refer to paint manufacturer’s recommendations.
2000 cadillac deville 1-11 Preparation of Service Part 1. Cut center pillar at laser weld location. This will allow a 25␣ mm (1␣ in) overlap to the vehicle for welding (Fig. 1-16). 2. Notch the weather strip flange to prevent excessive metal thickness in these areas.
1-12 2000 cadillac deville Outer Wheelhouse Sectioning Removal Procedure 1. Locate horizontal laser-weld line in upper quarter area (Fig. 1-18). 2. Measure down 25␣ mm (1␣ in) and scribe a cut line. 3. On the vehicle rocker area, locate and scribe a vertical cut line in the recommended section area.
2000 cadillac deville 1-13 Rear Rail Sectioning The rear rail is available as a complete assembly. It consists of an outer panel, two inner reinforcements, a rail extension, and all necessary component mounting brackets (Fig. 1-20). The outer panel and rear mounting brackets are also available separately to facilitate sectioning.
1-14 2000 cadillac deville Removal Procedure 1. Visually inspect and restore as much of the damage as possible to factory specifications. 2. Remove all related panels and components. 3. Cut the rear rail along the rearward flange of the crossbar (Fig.
2000 cadillac deville 1-15 Installation Procedure 1. Using the original part as a guide, mark a line on the service rail 35␣ mm (1-5/16␣ in) forward of the cut made to the original part; this should be approximately 535␣ mm (21␣ in) without the extension attached to the rail.
1-16 2000 cadillac deville ZERO LINE A B C D E F ALL LENGTHS MEASURED FROM Ø LINE AT TOP HINGE 19 MM HOLE ALL MEASUREMENTS HOLE CENTER TO CENTER 19 MM GAGE HOLE Ø Engine Compartment Dimensions – 2.
2000 cadillac deville 1-17 Ø C A B D E F G 540 469 552 526 925 888 1752 2537 3191 1092 348 358 537 496 504 427 430 496 553 577 D A TUM LINE WIDTH HEIGHT LENGTH Underbody Dimensions – 2000 Cadillac .
1-18 2000 cadillac deville ø A B C D E F D A TUM LINE 829 840 827 836 0 0 1140 1140 2183 849 591 930 964 665 1004 WIDTH HEIGHT LENGTH Body Side Dimensions – 2000 Cadillac DeV ille Description Locat.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Cadillac 2000 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Cadillac 2000 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Cadillac 2000, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Cadillac 2000 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Cadillac 2000, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Cadillac 2000.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Cadillac 2000. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Cadillac 2000 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.