Manuel d'utilisation / d'entretien du produit FOMIM-32 du fabricant Cabletron Systems
Aller à la page of 33
FOMIM-32/36/38 FIBER OPTIC MEDIA INTERFACE MODULE USER’ S GUIDE.
FOMIM User ’s Guide i NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made.
Notice ii FOMIM User ’s Guide DOC NOTICE This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
Notice FOMIM User ’s Guide iii CABLETRON SOFTWARE PROGRAM LICENSE 1. LICENSE . You have the right to use only the one (1) copy of the Program provided in this package subject to the terms and conditions of this License Agreement.
Notice iv FOMIM User ’s Guide DECLARATION OF CONFORMITY Application of Council Directive(s): 89/336/EEC 73/23/EEC Manufacturer ’ s Name: Cabletron Systems, Inc. Manufacturer ’ s Address: 35 Industrial Way PO Box 5005 Rochester, NH 03867 European Representative Name: Mr.
FOMIM User’ s Guide v CONTENTS CHAPTER 1 INTRODUCTION 1.1 Using This Manual ....................................................................... 1-1 1.2 Document Conventions ............................................................... 1-3 1.3 Fiber Optic Media Interface Modules.
Contents vi FOMIM User’ s Guide.
FOMIM User’ s Guide 1-1 CHAPTER 1 INTR ODUCTION W elcome to the Cabletron Systems FOMIM-32/36/38 Fiber Optic Media Interface Module User’s Guide . W e hav e designed this manual to serve as a simple installation and reference guide for the FOMIM, and to explain the capabilities and special features of the module.
Chapter 1: Introduction 1-2 FOMIM User’ s Guide Figure 1-1 The FOMIMs It is assumed that you hav e a general working kno wledge of Ethernet or IEEE 802.
Document Con ventions FOMIM User’ s Guide 1-3 1.2 DOCUMENT CON VENTIONS The follo wing con ventions are used throughout this document: 1.3 FIBER OPTIC MEDIA INTERFACE MODULES Cabletron Systems Fiber Optic Media Interface Modules pro vide a choice of six, twelve, or eighteen ports with ST connectors.
Chapter 1: Introduction 1-4 FOMIM User’ s Guide 1.3.2 Multi Media Access Centers The Cabletron Systems Fiber Optic Media Interface Modules are designed to be installed into the Cabletron Systems Multi Media Access Center (MMA C).
LANVIEW Status Monitoring System FOMIM User’ s Guide 1-5 Figure 1-2 LANVIEW LEDs The follo wing discusses the function of each LANVIEW LED on the FOMIM (Figure 1-2). Note that there is one Link OK (LNK) and one Recei ve (RCV) LED for each port on the MIM, as well as one Error (ERR) and one Collision (CLN) LED for the entire MIM.
Chapter 1: Introduction 1-6 FOMIM User’ s Guide Error (ERR) LED When lit, this red LED indicates the temperature within the MMA C chassis has risen to 40 ° C or greater . The FOMIM alerts the management board, and the FOMIM in turn recei ves a signal to light the LED.
Getting Help FOMIM User’ s Guide 1-7 • The serial and re vision numbers of all Cabletron Systems products in the network • The de vice history (i.
Chapter 1: Introduction 1-8 FOMIM User’ s Guide.
FOMIM User’ s Guide 2-1 CHAPTER 2 NETW ORK REQUIREMENTS AND INSTALLATION This chapter begins with netw ork design guidelines in Section 2.1, Network Cable Requirements , that must be met before installing the module in a network.
Chapter 2: Network Requirements and Installation 2-2 FOMIM User’ s Guide Propagation delay is the amount of time it takes a packet to travel from the sending device to the receiving device. Total propagation delay allowed for the entire network is 25.
Installing the FOMIM into the MMA C FOMIM User’ s Guide 2-3 2.3 INSTALLING THE FOMIM INTO THE MMA C Y ou can easily install the FOMIM into a Multi Media Access Center with a Flexible Netw ork Bus (MMA C-FNB). Install the FOMIM into the MMA C as follo ws: 1.
Chapter 2: Network Requirements and Installation 2-4 FOMIM User’ s Guide 2.4 CONNECTING FIBER OPTIC CABLING TO THE FOMIM Each fiber optic link consists of two strands of fiber optic cabling: the transmit (TX) and the recei ve (RX).
Connecting Fiber Optic Cabling to the FOMIM FOMIM User’ s Guide 2-5 4. At the other end of the fiber optic cable, attach the fiber pair to the transmit and receive ports of the device. If link indicators are present for the fiber optic connection, check that they are ON.
Chapter 2: Network Requirements and Installation 2-6 FOMIM User’ s Guide.
FOMIM User’ s Guide 3-1 CHAPTER 3 T ESTING AND T R OUBLESHOOTING This chapter lists the installation checkout procedures necessary to v erify that the segments connected to your FOMIM are operating properly . The chapter concludes with a description of the LANVIEW LEDs and their use in troubleshooting physical layer network problems.
Chapter 3: T esting and T roub leshooting 3-2 FOMIM User’ s Guide 5. Disconnect the jumpers from the barrel connector. 6. Using the jumper, attach the optical power meter to one end of one strand of the link segment. 7. Using the other jumper, attach the other end of the same strand to the optical source unit.
Pre-Installation T est FOMIM User’ s Guide 3-3 4. If the LEDs are not lit, reverse the cable ends back to their original positions, and contact Cabletron Systems Technical Support for assistance.
Chapter 3: T esting and T roub leshooting 3-4 FOMIM User’ s Guide If failures occur , refer to Section 3.3, Using LANVIEW , in this chapter . Figure 3-1 Pre-Installation T est 3.3 USING LANVIEW The FOMIM uses Cabletron Systems built-in visual diagnostic and status monitoring system called LANVIEW .
Using LANVIEW FOMIM User’ s Guide 3-5 If you are not able to resolve a problem with your FOMIM, call Cabletron Systems T echnical Support for assistance (see Chapter 1, Section 1.
Chapter 3: T esting and T roubleshooting 3-6 FOMIM User’ s Guide.
FOMIM User’ s Guide A-1 APPENDIX A FOMIM SPECIFICATIONS The operating specifications for the Cabletron Systems FOMIM are included in this Appendix. Cabletron Systems reserv es the right to change these specifications at any time without notice. A.
Appendix A: FOMIM Specifications A-2 FOMIM User’ s Guide A.2 EN VIR ONMENTAL REQUIREMENTS Operating T emperature: +5 ° to +40 ° C (41 ° to 104 ° F) Non-operating T emperature: -30 ° to +80 ° .
Agency Appro vals FOMIM User’ s Guide A-3 A.3 AGENCY APPRO V ALS Designed in accordance with UL478, UL910, NEC 725-2(b), CSA, IEC, TUV , VDE Class A. Meets FCC Part 15, Class A limits. PHYSICAL PROPER TIES Dimensions: 34.04 D x 29.21 H x 5.08 W cm (13.
Appendix A: FOMIM Specifications A-4 FOMIM User’ s Guide.
FOMIM User’ s Guide Index-1 INDEX C Cable connecting 2-4 distance 1-3 requirements 2-1 CLN LED 1-5 Conventions 1-3 D Design guidelines 2-1 E ERR LED 1-5 F FOMIM installing 2-3 specifications A-1 unp.
Index Index-2 FOMIM User’ s Guide.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Cabletron Systems FOMIM-32 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Cabletron Systems FOMIM-32 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Cabletron Systems FOMIM-32, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Cabletron Systems FOMIM-32 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Cabletron Systems FOMIM-32, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Cabletron Systems FOMIM-32.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Cabletron Systems FOMIM-32. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Cabletron Systems FOMIM-32 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
