Manuel d'utilisation / d'entretien du produit 5045 du fabricant Bush Hog
Aller à la page of 56
ASSEMBLY ● OPERATION ● MAINTENANCE 707 $4.00 50048390 Front End Loaders 3545 / 4045 / 5045 / 6045 Operator’s Manual BUSH HOG ®.
CONGRATULATIONS! You have invested in the best implement of its type on the market today. The care you give your Bush Hog implement will greatly determine your satisfaction with its performance and its service life.
3545 / 4045 / 5045 / 6045 TABLE OF CONTENTS SECTION/PARA PAGE Warranty .....................................................................2 Dealer Preparation Check List....................................3 Safety Alert Symbols .....................
LIMITED WARRANTY ✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯ Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from.
DEALER PREPARATION CHECK LIST 3545 / 4045 5045 / 6045 BEFORE DELIVERING MACHINE - The following check list should be completed. Use the Operator’s Manual as a guide. ❏ Machine properly assembled. ❏ All safety decals readable. (See decal page) ❏ All bolts tightened to torque specifications given in torque chart.
Safety Alert Symbol This Safety Alert Symbol means: “ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” This symbol is used to call attention to safety precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice.
IMPORTANT SAFETY PRECAUTIONS This symbol is used to call attention to safe- ty precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safety precautions could result in death or serious bodily injury.
10. Before disconnecting hydraulic lines, relieve all hydraulic pressure. 11. Do not tamper with the relief valve setting. The relief valve is pre-set at the factory. Changing the setting can cause overloading the loader and tractor and serious operator injury may result.
IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as such).
SECTION I INTRODUCTION AND DESCRIPTION 1-1 INTRODUCTION We are pleased to have you as a Bush Hog cus- tomer. Your Front End Loader has been carefully designed to give maximum service with minimum down time.
SERIES LOADER 3545 4045 5045 6045 A. Maximum Lift Height - Measured at Pivot Pin 120” 126” 133” 153” B. Maximum Lift Height - Under Level Bucket 110” 116” 123” 144” C. Clearance with Attachment Dumped 45° 92 in. 90” 97” 105 125” D.
TRACTORS THAT HAVE MOVABLE AXLES MUST BE SET FORWARD IN THE LONG WHEEL- BASE POSITION AS SHOWN IN FIGURE 2-1 TO PREVENT EXCESSIVE LEVERAGE BEING EXERTED ON THE TRACTOR FRAME. FAILURE TO DO SO CAN RESULT IN PERSONAL INJURY AND EQUIPMENT DAMAGE. REFER TO TRAC- TOR OPERATOR’S MANUAL FOR ABOVE PRO- CEDURES AND SPECIFICATIONS FOR YOUR TRACTOR.
C. Check that lift cylinders are fully retracted. Figure 2-3. Then drive tractor forward. Use bucket cylinders to position height of outer pedestal top pin. Figure 2-4. D. Align outer pedestal top pin with mounting bracket guide post on both sides. Make sure loader is centered right to left on both brackets.
2-3 DISMOUNTING LOADER CAUTION ALWAYS PARK LOADER WITH MATERI- AL BUCKET OR AUTHORIZED BUSH HOG ATTACHMENT ATTACHED TO THE LOADER. CAUTION BEFORE LEAVING THE TRACTOR SEAT, LOWER ATTACHMENT OR LOADER BOOM TO GROUND, STOP ENGINE, LOCK BRAKES, RELIEVE HYDRAULIC PRESSURE, AND REMOVE KEY.
MAKE SURE PARKED LOADER IS ON A HARD LEVEL SURFACE. ENGAGE ALL SAFETY DEVICES TO PREVENT LOADER FROM FALLING AND BEING DAMAGED OR INJURING SOMEONE. DO NOT REPAIR LOADER IF IT IS NOT MOUNTED ON THE TRACTOR. LOSS OF HYDRAULIC FLUID OR REMOVAL OF PARTS COULD CAUSE LOADER TO COLLAPSE RESULTING IN INJURY.
3-4 EXTERNAL LOADER AND/OR TRAC- TOR VALVE. NOTE When properly installed, the tractor remote valve or external valve control lever/levers will control the loader hydraulic circuits as described below. Refer to tractor Operator’s Manual for further explanation of tractor remote control lever/levers.
IMPORTANT Always keep the cylinders in a retracted position when the loader is not in use to guard against rust and contamination which may cause dam- age to the cylinder rods and hydraulic system.
FILLING THE BUCKET Approach and enter the pile with a level bucket. Loaders with 1-lever control, ease lever back and toward you to lift and rollback the bucket. Loaders with 2-lever controls, ease both levers back to lift and rollback the bucket. The lift and rollback of the bucket will increase effi- ciency because.
CARRYING THE LOAD Position the bucket as low as possible below the level of the tractor hood for maximum stability and visibility, whether the bucket is loaded or empty. Use extreme caution when operating the loader on a slope and keep the bucket as low as possible.
OPERATING WITH FLOAT CONTROL During hard surface operation, keep the bucket level and put the lift control in the float position to permit the bucket to float on the working surface. If hydraulic down pressure is exerted on the bucket, it will wear faster than normal.
PEELING AND SCRAPING BACKFILLING 6” Use a slight bucket angle, travel forward, and hold the lift control forward to start the cut. Make a short, angle cut approximately 6” deep and break-out cleanly. With the bucket level, start a cut at the notch approx- imately 2” deep.
Leave dirt in the bucket because dumping on each pass wastes time. Operate at right angles to the ditch. Take as big a bite as the tractor can handle without lugging down. DITCH SOIL PILE Leave dirt which drifts over the side of the bucket for final clean-up.
3-16 FORK LIFT OPERATION WARNING TO AVOID SERIOUS INJURY OR DEATH: ★ NEVER LIFT LARGE ROUND HAY BALES OR OTHER LOADS ON THE FORK LIFT ATTACHMENT THAT COULD ROLL BACK ONTO TRAC- TOR OPERATOR AREA. ★ NEVER USE FORK LIFT ATTACH- MENT TO LIFT OR SUPPORT PEOPLE.
22 3-18 SKID STEER QUICK HITCH OPERATION The quick hitch (Figure 3-6) is designed to allow easy mounting and dismounting of skid steer attachments from loader. With attachment on flat, level surface, mount as follows: Tilt quick hitch slightly forward at top and slowly drive into attachment.
SECTION IV MAINTENANCE 4-1 MAINTENANCE CHECK LIST Perform scheduled maintenance as outlined below. Lower machine to ground, turn off tractor, and set parking brake before doing maintenance inspections or work. All bolts should be torqued as recommend- ed in torque chart unless otherwise indicated.
4-3 HYDRAULIC SYSTEM PRESSURE REQUIREMENTS A tractor hydraulic system pressure setting of 2500 psi is recommended for maximum efficiency and ser- vice. Do not exceed 3000 psi as this will damage components possibly causing serious injury. The Bush Hog control valve is pre-set at the factory and should not be adjusted.
TABLE 4-1 TROUBLESHOOTING PROCEDURES PROBLEM POSSIBLE CAUSE REMEDY Loader slow and/or will not dump. Hydraulic oil viscosity too heavy. Change to proper oil. Oil filter plugged. Clean or replace filter. Hydraulic pump worn. Repair or replace pump. Oil line restricted or leaking.
SECTION V ASSEMBLY 1. Do not lift heavy parts or assemblies. Use crane, jack, tackle, fork trucks, or other mechanical devices. 2 Select an area for assembly that is clean and free of any debris which might cause persons working on the assembly to trip.
5-2 TRACTOR BALLAST Tractor weignt bracket may be left in place on cer- tain tractor models with loader mounted. Front trac- tor weights can only be used when the loader is parked. Weights must be removed before remount- ing loader or serious damage will occur to loader or tractor front axle due to excessive weight.
5-6 FORK LIFT OPTION Raise the positioning lock pins at the top of each fork. Place fork in the middle of the frame over the notch in the lower edge. Slide forks to desired posi- tions and lower pins to lock forks in place. 28 5-7 BALE SPEAR OPTION Insert long spear into top of frame and fasten with eccentric nut as shown.
5-8 OPTIONAL BUCKET ITEMS ASSEMBLY 29 SPILL GUARD ATTACHMENT 1. Place spill guard on bucket & center. 2. Mark hole centers for attaching fasteners. Allow clearance for side cutting edges on bolts in side plates if necessary. 3. Remove spill guard and drill 9/16” holes.
BOLT DI AMETE R W RENCH ( I N. ) “ B” AND SAE SAE SAE SI ZE ( I N. ) “A” THRE AD SI Z E GRADE 2 GRADE 5 GRADE 8 7/16 1/4 - 2O UNC 6 (7) 8 (11) 12 (16) 7/16 1/4 - 28 UNF 6 (8) 10 (13) 14 (18) 1.
SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damages can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge.
BUSH HOG L.L.C. W AL VOIL V AL VE MOUNTING INSTRUCTIONS 50051735 & 50051736 SINGLE HANDLE V AL VE KITS HYDRAULIC A TT ACHMENT FOR 3545, 4045, 5045, 6045 LOADERS (See Page 2 for V alve Mounting Instructions) INST ALLA TION NOTES z CAUTION: Before leaving tractor seat, stop engine, lock brake, relieve hydraulic pressure, and remove key .
Page 2 W AL VOIL V AL VE MOUNTING INSTRUCTIONS (See Page 3 for V alve Stand Mounting Instructions) V AL VE PLUMBING ASSEMBL Y Single Handle Controls shown.
Page 2 W AL VOIL V AL VE MOUNTING INSTRUCTIONS (See Page 3 for V alve Stand Mounting Instructions) V AL VE PLUMBING ASSEMBL Y Single Handle Controls shown.
BUSH HOG L.L.C. W AL VOIL V AL VE MOUNTING INSTRUCTIONS 50051735 & 50051736 SINGLE HANDLE V AL VE KITS HYDRAULIC A TT ACHMENT FOR 3545, 4045, 5045, 6045 LOADERS (See Page 2 for V alve Mounting Instructions) INST ALLA TION NOTES z CAUTION: Before leaving tractor seat, stop engine, lock brake, relieve hydraulic pressure, and remove key .
BUSH HOG L.L.C. MOUNTING INSTRUCTIONS 50051729 CABLE CONTROL V AL VE KIT 50051730 CABLE CONTROL V AL VE KIT HYDRAULIC A TT ACHMENT FOR MID MOUNT LOADERS (See Page 2 for Mounting Instructions) A TT ACHING HANDLE MOUNT , CONTROL HANDLE AND CABLES T O TRACTOR 1.
3. Assemble the mount to the support tube and handle to the support tube (refer to Fig. 1). Leave all fasteners snug but not tight. position the assembly on the area of the floor board chosen and adjust the assembly to be sure the operator has complete and comfortable access to the control handle.
Page 6 17. NOTE : This valve is set for a open center tractor hydraulic system. If tractor has a closed center system a closed center plug must be inst alled. Remove the open center plug in valve. Install the closed center plug furnished with the valve (Refer to Fig.
Page 4 8. Rotate the valve ends of the cables through the notch at the bottom of the support tube and through the large hole in the support mount and floor board of the tractor .
Page 4 8. Rotate the valve ends of the cables through the notch at the bottom of the support tube and through the large hole in the support mount and floor board of the tractor .
Page 6 17. NOTE : This valve is set for a open center tractor hydraulic system. If tractor has a closed center system a closed center plug must be inst alled. Remove the open center plug in valve. Install the closed center plug furnished with the valve (Refer to Fig.
3. Assemble the mount to the support tube and handle to the support tube (refer to Fig. 1). Leave all fasteners snug but not tight. position the assembly on the area of the floor board chosen and adjust the assembly to be sure the operator has complete and comfortable access to the control handle.
Sept. - 0 5 Instruction Sheet No. 25H46344 Sept. -05 Instruction Sheet No. 25H46344 INST ALLA TION INSTRUCTIONS FOR 24H46343 POWER BEYOND KIT The POWER BEYOND KIT is only required if connecting to an open center tractor hydraulic system.
Power Beyond Plug V alve Plug S traight Adapter 90° Elbow B C A T o Pressurized Return Inlet T o Sump Inlet (Use Long Hose Here) T o Pressure Inlet These hoses to be furnished by dealer .
Power Beyond Plug V alve Plug S traight Adapter 90° Elbow B C A T o Pressurized Return Inlet T o Sump Inlet (Use Long Hose Here) T o Pressure Inlet These hoses to be furnished by dealer .
Sept. - 0 5 Instruction Sheet No. 25H46344 Sept. -05 Instruction Sheet No. 25H46344 INST ALLA TION INSTRUCTIONS FOR 24H46343 POWER BEYOND KIT The POWER BEYOND KIT is only required if connecting to an open center tractor hydraulic system.
50051690 SELF LEVELING V AL VE BUNDLE MOUNTING INSTRUCTIONS BUSH HOG 3545, 4045, 5045 & 6045 MID MOUNT FRONT END LOADERS ~ ASSEMBL Y INSTRUCTIONS ~ 1. Att ach self leveling valve to the right hand pedestal using the (2) 5/16”- 2 1/2” Gr . 5 capscrews, 5/16” lockwashers and 5/16” hex nuts provided in kit.
A - Attach to metal line on mainframe that is connected to the Base End of the lif t cylinder (color code blue) using a 68” hydraulic hose and adapter provided in kit. B - Attach to control valve at port that controls Base End of the lift cylinder , (color code blue).
A - Attach to metal line on mainframe that is connected to the Base End of the lif t cylinder (color code blue) using a 68” hydraulic hose and adapter provided in kit. B - Attach to control valve at port that controls Base End of the lift cylinder , (color code blue).
50051690 SELF LEVELING V AL VE BUNDLE MOUNTING INSTRUCTIONS BUSH HOG 3545, 4045, 5045 & 6045 MID MOUNT FRONT END LOADERS ~ ASSEMBL Y INSTRUCTIONS ~ 1. Att ach self leveling valve to the right hand pedestal using the (2) 5/16”- 2 1/2” Gr . 5 capscrews, 5/16” lockwashers and 5/16” hex nuts provided in kit.
BUSH HOG ® P.O. BOX 1039 • SELMA, AL 36702-1039 Instruction Sheet 25H49884 MOUNTING INSTRUCTIONS FOR 24H49871 GRAPPLE A TT ACHMENT 1. Attach the screen to inner arm with (4) 1/2” x 5” capscrew , (4) 1/2” lockwashers, and (4) 1/2” Hex Nuts. 2.
25H49899 (4) Tines 25H49896 Cross Tube 25H49900 Screen 25H49893 Bolt Pad 25H49893 Bolt Pad 25H49890 Outer Arm 25H49890 Outer Arm Cross Tube to Tine (4) 5/8” x 2-1/2” Capscrews (4) 5/8” Lockwashe.
24H49871 GRAPPLE A TT ACHMENT P ART NUMBER QTY . P ART NAME 25H47945 2 Hydraulic Cylinder 1560384 4 Hydraulic Hose 60” 1560370 2 Hydraulic Hose 48” 25H49906 2 Clamp Plate 25H49900 1 Screen 25H4989.
P.O. Box 1039 ● Selma, AL 36702-1039 Telephone (334) 874-2700 ● www.bushhog.com.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Bush Hog 5045 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Bush Hog 5045 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Bush Hog 5045, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Bush Hog 5045 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Bush Hog 5045, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Bush Hog 5045.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Bush Hog 5045. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Bush Hog 5045 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
