Manuel d'utilisation / d'entretien du produit 5900859 du fabricant Briggs & Stratton
Aller à la page of 52
Operator’ s Manual S75X Series Compact Zer o- T urn Riding Mowe r BRIGGS & STRATTON POWER PRODUCTS GROUP , LLC. 5375 NORTH MAIN STREET MUNNSVILLE, NY 13409 800 933 6175 5102230 Re v B Model Numb.
Briggs & Stratton Power Products Group, LLC. Copyright © 2011 Briggs & Stratton Corporation Milwaukee, WI, USA. All rights reserved. SNAPPER PRO is a trademark of Briggs & Stratton Corporation Milwaukee, WI, USA. Contact Information: Briggs & Stratton Power Products Group, LLC.
1 Table of Contents Operator Safety .................................................. 2 Safety Decals ..........................................................8 Safety Interlock System ..........................................9 Safety Icons .......
2 Operator Safety Operating Safety Congratulations on purchasing a superior-quality piece of lawn and garden equipment. Our products are designed and manufactured to meet or exceed all industry standards for safety. Do not operate this machine unless you have been trained.
3 Operator Safety Slope Operation Operation on slopes can be dangerous. Using the unit on a slope that is too steep where you do not have adequate wheel traction (and control) can cause sliding, loss of steering, control, and possible rollover. You should not operate on a slope greater than a 5.
4 Operator Safety Enclosed Areas Only operate this unit outdoors and away from unventilated areas such as inside garages or enclosed trailers. The engine emits poisonous carbon monoxide gas and prolonged exposure in an enclosed area can result in serious injury or death.
5 Operator Safety 3. Be sure all drives are in neutral and parking brake is engaged before starting engine. Only start engine from the operator’s position. Use seat belts if provided. 4. Be sure of your footing while using pedestrian controlled equipment, especially when backing up.
6 Operator Safety 25. OSHA regulations may require the use of hearing protection when exposed to sound levels greater than 85 dBA for an 8 hour time period. SLOPE OPERATION Slopes are a major factor related to loss-of-control and tip-over accidents, which can result in severe injury or death.
7 Operator Safety SERVICE AND MAINTENANCE To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Safe Handling of Gasoline 1. Extinguish all cigarettes, cigars, pipes, and other sources of ignition.
8 www.snapperpro.com Operator Safety Safety Decals This unit has been designed and manufactured to provide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing.
9 Safety Interlock System This unit is equipped with safety interlock switches. These safety systems are present for your safety, do not attempt to bypass safety switches, and never tamper with safety devices.
10 www.snapperpro.com Identification Tag Features and Controls SAMPLE SAMPLE When contacting your authorized dealer for replacement parts, service, or information you MUST have these numbers. Record your part number, serial number and engine serial numbers in the space provided for easy access.
11 Control Functions The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing require the combined use of several controls applied in specific sequences. To learn what combination and sequence of controls to use for various tasks see the OPERATION section.
12 www.snapperpro.com Ignition Switch The ignition switch starts and stops the engine, it has three positions: OFF Stops the engine and shuts off the electrical system. RUN Allows the engine to run and powers the electrical system. START Cranks the engine for starting.
13 Operation General Operating Safety Before first time operation: • Be sure to read all information in the Safety and Operation sections before attempting to operate this tractor and mower. • Become familiar with all of the controls and how to stop the unit.
14 www.snapperpro.com WARNING If you do not understand how a specific control functions, or have not yet thoroughly read the FEATURES & CONTROLS section, do so now. Do NOT attempt to operate the tractor without first becoming familiar with the location and function of ALL controls.
15 Operation Zero Turn Driving Practice The lever controls of the Zero Turn rider are responsive, and learning to gain a smooth and efficient control of the rider’s forward, reverse, and turning movements will take some practice.
16 www.snapperpro.com Advanced Driving Executing an End-Of-Row Zero Turn Your Zero Turn Rider’s unique ability to turn in place allows you to turn around at the end of a cutting row rather than having to stop and Y-turn before starting a new row. For example, to execute a left end-of row zero turn: 1.
17 Mowing 1. Engage the parking brake. Make sure the PTO switch is disengaged, the ground speed control levers are in the NEUTRAL position and the operator is on the seat. 2. Set the mower cutting height. 3. Start the engine (see STARTING THE ENGINE).
18 www.snapperpro.com When and How Often to Mow The time of day and condition of the grass greatly affect the results you’ll get when mowing. For the best results, follow these guidelines: 1. Mow when the grass is between three and five inches high.
19 Proper Mulching Mulching consists of a mower deck which cuts and recuts clippings into tiny particles and which then blows them down INTO the lawn. These tiny particles decompose rapidly into by-products your lawn can use. UNDER PROPER CONDITIONS, your mulching mower will virtually eliminate noticeable clippings on the lawn surface.
20 www.snapperpro.com WARNING Fuel and its vapors are extremely flammable and explosive. Fire or explosion can cause severe burns or death. Never store the unit, with gasoline in the engine or fuel tank, in a heated shelter or in enclosed, poorly ventilated enclosures.
21 Maintenance Maintenance Schedule The following schedule should be followed for normal care of your rider and mower. You will need to keep a record of your operating time. Determining operating time is easily accomplished by observing the elapsed time recorded by the hour meter.
22 www.snapperpro.com Regular Maintenance Checking / Adding Fuel To add fuel: 1. Remove the fuel cap (see Figure 1). 2. Fill the tank to the bottom of the filler neck. This will allow for fuel expansion. NOTE: Do not overfill. Refer to your engine manual for specific fuel recommendations.
23 Regular Maintenance Change Oil & Filter 1. Warm engine by running for a few minutes. (Refer to the engine operator’s manual for oil & filter replacement instructions.) 2. Route the oil drain hose ( A, Figure 13 ) over the side of the engine deck and underneath the fuel tank.
24 www.snapperpro.com Servicing the Hydraulic System Removing the Tank The right hand tank ( A, Figure 14 ) must be removed prior to checking and/or changing the hydraulic oil. 1. Unscrew the three (3) wing bolts ( B ) that secure the tank to the unit.
25 Lubrication Lubricate the unit at the locations shown in Figures 16 through 20 as well as the following lubrication points. Grease: • front caster wheel axles & yokes • deck lift pivot blocks • mower deck & pump drive idler arm • motion control pivots Use grease fittings when present.
26 www.snapperpro.com Regular Maintenance Servicing the Mower Blades Removing the Mower Blade 1. To remove the mower blade, wedge a wooden block between the mower blade and the mower deck housing to keep the blade from turning and remove the mower blade mounting bolt with a 15/16” wrench ( Figure 21 ).
27 Figure 26. Tightening the Mower Blade for Installation A. Mower Blade Mounting Bolt B. Flat Washer C. Mower Blade Air Lift (Points Up For Installation) D. 4 X 4 Wooden Block D A B A B Figure 24. Sharpening the Mower Blade A. Mower Blade Bevel B. Mower Blade Cutting Edge Figure 25.
28 www.snapperpro.com Regular Maintenance Seat Adjustment The height of the seat ( A, Figure 27 ) can be adjusted either up or down to accomidate the operator’s comfort level.
29 Speed Balancing Adjustment If the unit veers to the right or left when the ground speed control levers are in either the maximum forward (both ground speed control levers contacting the handle bars.
30 www.snapperpro.com Regular Maintenance Figure 31. Adjusting the Range Selector Plate A. Range Selector Hardware B. Range Selector Pivot Hardware C. Range Selector Plate D.
31 Adjusting the Parking Brake Spring 1. Locate the two (2) brake springs ( A, Figure 32 ). 2. With the parking brake engaged, measure the compressed spring length. The spring should be 2-3/8” (6 cm) when compressed. 3. If the spring length does not equal the measurement, the spring length will need to be adjusted.
32 www.snapperpro.com Suspension Adjustment The shock assembly can be adjusted in two ways to allow the operator to customize the ride according to the operator’s weight and/or operating conditions. You have the option of adjusting the spring pre-load and/or the upper mounting position.
33 Regular Maintenance Mowing Height Adjustment See Figure 34. The mowing height can be adjusted by turning the cutting height adjustment handle. To Raise the Mower Deck: Turn the cutting height adjustment handle ( A, Figure 34 ) CLOCKWISE. To Lower the Mower Deck: Turn the cutting height adjustment handle COUNTER- CLOCKWISE.
34 www.snapperpro.com Deck Lift Rod Timing Adjustment 1. Park the machine on a flat, level surface. Disengage the PTO, stop the engine, and engage the parking brake. Rear tires must be inflated to 15 psi (1,03 bar). 2. Measure and record the distance between the lift pivots and the rod pivots.
35 Deck Leveling Adjustment NOTE: Before adjusting the deck level, the deck lift rod timing must be checked and/or adjusted. 1. Park the machine on a flat, level surface. Disengage the PTO, stop the engine and engage the parking brake. Rear tires must be inflated to 15 psi (1,03 bar).
36 www.snapperpro.com PTO Drive Belt Replacement 1. Park the unit on a smooth, level surface such as a concrete floor. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key. 2. Remove the mower deck guard. 3. Position the mower deck in the TRANSPORT position.
37 Regular Maintenance Mower Deck Drive Belt Replacement 1. Park the unit on a smooth, level surface such as a concrete floor. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key. 2. Remove the mower deck guard.
38 www.snapperpro.com Regular Maintenance Hydraulic Pump Drive Belt Replacement 1. Park the unit on a smooth, level surface such as a concrete floor. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key. 2. Remove the PTO drive belt (see PTO DRIVE BELT REPLACEMENT for removal instructions).
39 7” (17,8 cm) A E B Figure 49. Pump Drive Belt Routing A. Nut B. Spring Anchor Eyebolt C. Pump Drive Pulleys D. Crankshaft Pulleys E. Anchor Tab F. Spring G. Idler Arm C D G C F Regular Maintenance Fuse Locations The fuse block is located underneath the left instrument control panel.
40 www.snapperpro.com Regular Maintenance Removing the Mower Deck It may be necessary to remove the mower deck to facilitate servicing the mower deck. The following procedure details how to remove the mower deck from the unit. 1. Park the machine on a flat, level surface such as a concrete floor.
41 Regular Maintenance Figure 54. Removing the Hanger Chains A. Hanger Chain B. Deck Lift Rod Pivot B B Figure 55. Disconnecting the Idler Arm Mount Plate A. Mounting Hardware B. Idler Arm Mount Plate C. Mower Deck C A B A A A B F E D C Figure 56. Pusher Rollers A.
42 www.snapperpro.com Battery Service Checking Battery Voltage A voltmeter can be used to determine condition of battery. When engine is off, the voltmeter shows battery voltage, which should be 12 volts. When engine is running, the voltmeter shows voltage of charging circuit which normally is 13 to 14 volts.
43 To Starter Switch Starting V ehic le Battery T o Gr ound To Starter Switch Dischar ged V ehic le Battery Engine Block THIS HOOK-UP FOR NEGA TIVE GR OUND VEHICLES MAKE CERT AIN VEHICLES DO NO T T OUCH Jumper Cab le Jumper Cab le Figure 57.
44 www.snapperpro.com Troubleshooting Troubleshooting Chart While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly.
45 Troubleshooting the Rider continued PROBLEM CAUSE REMEDY Engine runs, but rider will not drive. 1. Hydraulic release valve(s) in “open” position. 2. Belt is broken. 3. Drive belt slips. 4. Brake is not fully released. 1. Turn hydraulic release valve(s) CLOCKWISE to close.
46 www.snapperpro.com Troubleshooting Troubleshooting Common Cutting Problems PROBLEM CAUSE REMEDY Streaking 1. Blades are not sharp. 2. Blades are worn down too far. 3. Engine speed is too slow. 4. Ground speed is too fast. 5. Deck is plugged with grass.
47 Specifications Specifications are correct at time of printing and are subject to change without notice. ENGINE For models 5900918 22 Gross HP† Kawasaki Make Kawasaki Model FS651V-AS00-S Displacement 44.3 Cu. in (726 cc) Electrical System 12 volt, 15 amp.
48 www.snapperpro.com THIS IS A 15 DEGREE SLOPE INSTRUCTIONS 1. Fold this page along the dotted line indicated above. 2. Align the left edge of this guide with a vertical tree , a power line pole, a fence post, or any vertical structure. 3. Compare the angle of the fold with the angle of the hill.
Thank you f or purchasing Snapper Pro commercial mowing equipment. Please take a f ew minutes to read this limited warr anty information. It con- tains all the information you will need to ha ve y our Snapper Pro mower repaired in the unlik ely ev ent that a breakdown cov ered by this limited w arranty should occur .
Operator’ s Manual S75X Series Compact Zer o- T urn Riding Mowe r BRIGGS & STRATTON POWER PRODUCTS GROUP , LLC. 5375 NORTH MAIN STREET MUNNSVILLE, NY 13409 800 933 6175 Not for Reproduction.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Briggs & Stratton 5900859 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Briggs & Stratton 5900859 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Briggs & Stratton 5900859, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Briggs & Stratton 5900859 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Briggs & Stratton 5900859, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Briggs & Stratton 5900859.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Briggs & Stratton 5900859. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Briggs & Stratton 5900859 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
