FR
Telefunken logo
Notice d'utilisation officielle

Telefunken D48F275A3C

77 pages·7.3 MB·Téléviseur LED·PDF·ENITNLJA
Telefunken D48F275A3C
Table des matières 57 sections CAUTION · RISK OF ELECTRIC SHOCK · DO NOT OPEN · Getting Started · … AfficherMasquer
Page 1 of the Telefunken D48F275A3C user manual — CAUTION
Page 1 · cliquer pour agrandir
Page 1

Appendix B: HBBTV System 41 Software Upgrade 42 Troubleshooting & Tips 42 Internet Browser 44 PC Input Typical Display Modes 45 AV and HDMI Signal Compatibility 45 Supported DVI Resolutions 47

Safety Information 26 Getting Started 27 Notifications & Features & Accessories 27 Remote Control 30 Connections 31 First Time Installation - USB Connections 32 TV Menu Features and Functions 35 General TV Operation 38

If there is lightning or storms, or if the TV is not going to be used for a while (e.g. if going away on holiday), disconnect the TV set from the mains. The mains plug is used to disconnect TV set from the mains and therefore it must remain readily operable.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

To operate your TV in extreme ambient conditions may cause damage of the device.

  • The TV should not be placed near to open flames or sources of intense heat such as an electric heater.
  • Excessive sound pressure from earphones and headphones can cause hearing loss.
  • Ensure that no open flame sources, such as lit candles, are placed on top of the TV.
  • To prevent injury, this TV must be securely attached to the wall in accordance with the installation instructions (if the option is available).
  • Occasionally, a few non-active pixels may appear on the screen as a fixed blue, green or red point. Please note that this does not affect the performance of your product. Take care not to scratch the screen with fingernails or other hard objects.
  • Before cleaning, unplug the TV from the wall socket. Only use a soft, dry cloth while cleaning.
  • For ventilation purposes, leave a free space of at least 10 cm all around the set.
  • Do not block ventilation holes.
  • Do not place the TV on sloping or unstable surfaces, the TV may tip over.
  • Use this device in moderate climates.
  • The power cord plug should be easily accessible. Do not place the TV, furniture, etc. on the power cord. A damaged power cord/plug can cause fire or give you an electric shock. Handle the power cord by the plug, do not unplug the TV by pulling the power cord. Never touch the power cord/plug with wet hands as this could cause a short circuit or electric shock. Never make a knot in the power cord or tie it with other cords. When damaged it must be replaced, this should only be done by qualified personnel.

Risk of electric shock Dangerous voltage risk

  • Do not use this TV in a humid or damp place. Do not expose the TV to liquids. If any liquid falls into the cabinet unplug the TV and have it checked by qualified personnel before operating it any further.
  • Do not expose the TV to direct sunlight or other heat sources.

Contents · Safety Information

Page 2 of the Telefunken D48F275A3C user manual — Getting Started
Page 2 · cliquer pour agrandir
Page 2

Getting Started

Notifications & Features & Accessories

  • Automatic programming system.
  • Manual tuning.

This television is designed to consume less energy to help save the environment. To reduce energy consumption, you should take the following steps:

  • Automatic power down after up to six hours.
  • Sleep timer.

You can use the Power Save Mode setting, located in the Picture menu. If you set the Power Save Mode as Eco, the TV will switch to energy-saving mode and the luminance level of TV set will be decreased to the optimum level. Note that some picture settings will be unavailable to be changed when the TV is in Power Save Mode.

  • Child lock.
  • Automatic sound mute when no transmission.
  • NTSC playback.
  • AVL (Automatic Volume Limiting).
  • PLL (Frequency Search).
  • PC input.

If pressed Right button, “Screen will be off in 15 seconds.” message will be displayed on the screen. Select PROCEED and press OK to turn the screen off immediately. If you don’t press any button, the screen will be off in 15 seconds. Press any button on the remote or on the TV to turn the screen on again. If you disable Power Save Mode, picture mode will be automatically set to Dynamic.

  • Plug&Play for Windows 98, ME, 2000, XP, Vista, Windows 7.
  • Game Mode (Optional).
  • Ethernet (LAN) for Internet connectivity and service.
  • 802.11n WIFI Support (Optional).
  • HbbTV.
  • DLNA.

When the TV is not in use, please switch off or disconnect the TV from the mains plug. This will also reduce energy consumption.

  • Remote Control
  • Batteries: 2 x AAA
1. If the TV does not receive any input signal (e.g. from an aerial or HDMI source) for 5 minutes, the TV will go into standby. When you next switch-on, the following message will be displayed: “TV switched to stand-by mode automatically because there was no signal for a long time” . Press OK to continue.
  • Instruction Book
  • Side AV Connection Cable

TV Control Switch & Operation

2. If the TV has been left on and not been operated for a while, the TV will go into standby. When you next switch-on, the following message will be displayed. “TV switched to stand-by mode automatically because no operation was made for a long time” Press OK to continue.
  • Remote controlled colour LCD TV.
  • Fully integrated digital terrestrial/cable/satellite TV (DVB-T/C/S-S2).
  • HDMI inputs are for connecting a device that has a HDMI socket.
1. Up direction
  • USB input.
2. Down direction
  • OSD menu system.
3. Programme/Volume / AV / Standby-On selection switch
  • Scart socket for external devices (such as DVD Players, PVR, video games, etc.)

The Control button allows you to control the Volume/ Programme/ Source and Standby-On functions of the TV.

  • Stereo sound system.
  • Teletext.
  • Headphone connection.
Show 4 more labels / short text on this page
Environmental Information · Accessories Included · Standby Notifications · Features
Page 3 of the Telefunken D48F275A3C user manual — TRADEMARK ACKNOWLEDGMENT
Page 3 · cliquer pour agrandir
Page 3

To change volume: Increase the volume by pushing the button up. Decrease the volume by pushing the button down.

Connect the aerial or cable TV plug to AERIAL INPUT (ANT-TV) or satellite lead to LNB INPUT(ANT SAT) socket located on the rear bottom side of the TV.

To change channel: Press the middle of the button, the channel information banner will appear on screen. Scroll through the stored channels by pushing the button up or down

To change source: Press the middle of the button twice, the source list will appear on screen. Scroll through the available sources by pushing the button up or down.

To turn the TV off: Press the middle of the button down and hold it down for a few seconds, the TV will turn into standby mode.

Operation with the Remote Control

Press the MENU button on your remote control to display the main menu screen. Use the “ ” or “ ” buttons to select a menu tab and press the OK button to select option. Use the “ ” or “ ” or “ ” or “ ” buttons to select or set an item. Press BACK/ RETURN or MENU button to quit a menu screen. Input Selection Once you have connected external systems to your TV, you can switch to different input sources. Press the AV button on your remote control consecutively to select the different inputs. Changing Channels and Volume You can change the channel and adjust the volume by using the V+/- and P+/- buttons on the remote.

Manufactured under license from Dolby Laboratories.

TRADEMARK ACKNOWLEDGMENT

“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

“HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.”

“DLNA®, the DLNA Logo and DLNA CERTIFIED® are trademarks, service marks, or certification marks of the Digital Living Network Alliance.”

Inserting the Batteries into the Remote

Lift the cover on the back of the remote upward gently. Install two AAA batteries. Make sure to match the + and - ends of the batteries in the battery compartment (observe the correct polarity) Replace the cover.

YouTube and the YouTube logo are trademarks of Google Inc.

Information for Users on Disposal of Old Equipment and Batteries

Telefunken D48F275A3C — TRADEMARK ACKNOWLEDGMENT diagram (page 3)
Fig. 1

These symbols indicate that equipment with these symbols should not be disposed of as general household waste. If you want to dispose of the product or battery, please consider the collection systems or facilities for appropriate recycling.

that this battery contains lead.

Show 6 more labels / short text on this page
Antenna/Cable/Satellite Connection · Notification · [European Union only] · Connect Power · Battery · Products
Page 4 of the Telefunken D48F275A3C user manual — Operation with the Remote Control
Page 4 · cliquer pour agrandir
Page 4

TV Broadcasting PAL SECAM BG/I/DK/LL’

Receiving Channels VHF (BAND I/III) - UHF (BAND U) - HYPERBAND

Digital Reception Fully integrated digital terrestrial-cable-satellite TV(DVB-T-C-S)

Number of Preset Channels

Channel Indicator On Screen Display

RF Aerial Input 75 Ohm (unbalanced)

Operating Voltage 220-240V AC, 50Hz.

Audio Output Power (WRMS.) (10% THD)

Power Consumption 75 W

TV Dimensions DxLxH (with foot)

220 x 1093 x 681 mm

TV Dimensions DxLxH (without foot)

81/99 x 1093 x 642 mm

Operation temperature and operation humidity

0ºC up to 40ºC, 85% humidity max

Show 5 more labels / short text on this page
Specification · (DVB-S2 compliant) · Audio German+Nicam Stereo · 2x8 W · Weight 13,10 kg
Page 5 of the Telefunken D48F275A3C user manual — Digital Teletext (for UK only)
Page 5 · cliquer pour agrandir
Page 5

Getting Started

1. Standby 2. Numeric buttons 3. TV-AV / Channel List / DVB-T 4. Volume up/down 5. Mute 6. Navigation buttons 7. Menu on/off 8. OK / Channel List 9. Return/Back 10. Internet browser 11. Media Browser 12. My button 1 (*) 13. Coloured Buttons 14. Mono-Stereo Dual I-II / Audio-Subtitle Language 15. Subtitle on-off / Subtitle (in Media Browser mode) 16. Rewind (in Media Browser mode) 17. No Function 18. Play (in Media Browser mode) 19. Stop (in Media Browser mode) 20. Pause (in Media Browser mode) 21. Fast Forward (in Media Browser mode) 22. Image size 23. Teletext 24. My button 2 / Channel network type (**) 25. Electronic Programme Guide 26. Exit 27. Quick menu 28. Info 29. Programme Up-Down 30. Previous programme 31. AV / Source selection

Telefunken D48F275A3C — Getting Started diagram (page 5)
Fig. 2 · Getting Started

Using My button 1 (*) This button’s main function is to run Youtube link. However, if you want to change this function, you can press MY BUTTON 1 for five seconds when on a desired source, channel or link, until the “MY BUTTON IS SET” message is displayed on the screen. This confirms that the selected MY BUTTON is now associated with the selected function. Note that if you perform first time installation, MY BUTTON 1 will return to its default function. Using My Button 2 (**) This button’s main function is to switch between DVB-T, DVB-C and DVB-S broadcasts. However, if you press MY BUTTON 2 for five seconds, you can set a function to it as described in My Button 1. Note that if you perform first time installation, MY BUTTON 2 will return to its default function.

Teletext

Press TXT button to enter. Press again to activate mix mode. Press once more to exit. Follow the instructions displayed on digital teletext screen.

Digital Teletext (for UK only)

Press TXT button to view digital teletext information. Operate it with the coloured buttons, cursor buttons and the OK button. The operation method may differ depending on the contents of the digital teletext. Follow the instructions displayed on the digital teletext screen. When the TXT button is pressed again, the TV returns to television broadcast.

Remote Control

Page 6 of the Telefunken D48F275A3C user manual — HEADPHONE
Page 6 · cliquer pour agrandir
Page 6

Getting Started

Connector Type Cables Device

NOTE: When connecting a device via the YPbPr or Side AV input, you must use connection cables to enable connection. See the illustrations on the left side. | To enable PC audio, you will need to use SIDE AV CONNECTION cable’s WHITE & RED inputs. | If an external device is connected via the SCART socket, the TV will automatically switch to AV mode.| When receiving DTV channels (Mpeg4 H.264) or while in Media Browser mode, output will not be available via the scart socket. | When using the wall mounting kit (optional), we recommend that you plug all your cables into the back of the TV before mounting on the wall. | Insert or remove the CI module only when the TV is SWITCHED OFF. You should refer to the module instruction manual for details of the settings. | Each USB input of your TV supports devices up to 500mA. Connecting devices that have current value above 500mA may damage your TV.

VGA

Side Audio/Video Connection Cable

HDMI

SPDIFF

SIDE AV Side AV

If you want to connect a device to the TV, make sure that both the TV and the device are turned off before making any connection. After the connection is done, you can turn on the units and use them.

HEADPHONE

USB

Show 36 more labels / short text on this page
Connections · Scart · Connection · (back) · Connection · (back) · SIDE AV PC/YPbPr · Audio · Connection · (side) · PC Audio Cable · (Supplied) · (Not supplied) · Connection · (back) · (Coaxial Out) · Connection · (back) · (Audio/Video) · Connection · AV Connection Cable · (side) · (supplied) · Headphone · Connection · (side) · YPBPR YPbPr Video · Connection · (side) · YPbPr Connection Cable · (not supplied) · Connection · (side) · Connection · CAM module · (side)
Page 7 of the Telefunken D48F275A3C user manual — Aerial Installation
Page 7 · cliquer pour agrandir
Page 7

Getting Started

First Time Installation - USB Connections

(*) LCN is the Logical Channel Number system that organizes available broadcasts in accordance with a recognizable channel sequence (if available).

To Switch the TV On

Connect the power cord to the 220-240V AC, 50 Hz.

Press MENU button to quit channel list and watch TV.

To switch on the TV from standby mode either:

Cable Installation If you select Cable option and press OK button on the remote control a confirmation screen will be displayed. Select YES and press OK to proceed. To cancel operation, select NO and press OK. You can select frequency ranges from next screen. Enter the frequency range manually by using the numeric buttons. When finished, press OK button to start automatic search. Note: Searching duration will change depending on the selected search step.

Press the “ ” button, CH / CH or a numeric button on the remote control.

Press the side function switch until the TV comes on from standby.

To Switch the TV Off

Press the “ ” button on the remote control or press the side function switch until the TV switches into standby mode.

To power down the TV completely, unplug the power cord from the mains socket.

Satellite Installation If you select Satellite option from the search type selection screen, you can set a satellite and watch satellite channels. When you select Satellite installation, Antenna Type menu will be displayed. You can select Antenna type as Direct, Unicable or DiSEqC switch. Direct: If you have a single receiver and a direct satellite dish, select this antenna type. After selecting Direct, another menu screen will be displayed. Select an available satellite and press OK to scan for services.

When turned on for the first time, the language selection screen is displayed. Select the desired language and press OK.

On the next screen, set your preferences using the navigation buttons and when finished, press OK to continue.

Unicable: If you have multiple receivers and a unicable system, select this antenna type. Press OK to continue. Configure settings by following instructions on the screen. Press OK to scan for services.

DiSEqC switch: If you have multiple satellite dishes and a DiSEqC switch, select this antenna type. After selecting DiSEqC switch, another menu screen will be displayed. You can set four DiSEqC options (if available). Press GREEN button to scan all satellites or press YELLOW button to scan only the highlighted satellite. To save and exit press OK button.

You can activate Store Mode option at this point. This option is intended only for store use. It is recommended to select Home Mode for home use. If Store Mode is selected, a confirmation screen will be displayed. Select YES to proceed. This option will be available in Other Settings menu and can be turned off/on later.

If Home Mode is selected, Store Mode will not be available after the First Time Installation. Press OK button to continue.

(*) Some options may not be available depending on the country selection.

Aerial Installation

If you select Aerial option from the search type selection screen, the television will search for digital terrestrial TV broadcasts. After all the available stations are stored, the Channel List will be displayed on the screen.

While the search continues a message will appear, asking whether you want to sort channels according to the LCN(*). Select Yes and press OK to confirm.

Switching On/Off · First Time Installation

Page 8 of the Telefunken D48F275A3C user manual — To Switch the TV On
Page 8 · cliquer pour agrandir
Page 8

Using SatcoDX Feature SatcoDX (optional): You can perform SatcoDX operations using the Satelite Settings menu. In the SatcoDX menu, there are two options regarding to the SatcoDx. You can download or upload SatcoDX data. In order to perform these functions a USB device must be connected to the TV. You can upload current services and related satellites & transponders in TV, to a USB device. Additionally you can download one of the SatcoDx files stored in USB device, to the TV. When you select one of these files, all services and related satellites and transponders in the selected file will be stored in the TV. If there are any installed terrestrial, cable and/or analog services, they will be kept and only satellite services will be removed. Afterwards, check your antenna settings and make changes if necessary. An error message stating “No Signal” may be displayed if the antenna settings are not configured properly.

You can play photo, music, and movie files stored on a USB disk by connecting it to your TV. Connect a USB disk to one of the USB inputs located on the side of the TV. Pressing the MENU button while in the Media Browser mode will access the Picture, Sound and Settings menu options. Pressing the MENU button again will exit from this screen. You can set your Media Browser preferences by using the Settings menu.

Start playback with and

TV plays next file and loop the list.

Start playback with OK and

The same file will be played in a loop (repeat).

Start playback with OK/

The file will be played in a shuffle.. Quick Menu

Quick Settings menu allows you to access some options quickly. This menu includes Power Save Mode, Picture Mode, Equalizer Settings, Favourites, Sleep Timer, FollowMe TV (optional) and Information booklet (optional), CEC RC Passthrough options. Press Q.MENU button on the remote control to view quick menu. See the following chapters for the details of the listed features. FollowMe TV (optional) With your mobile device you can stream the current broadcast from your smart TV using the FollowMe TV feature. Install the appropriate Smart Center application to your mobile device. Start the application. For further information on using this feature refer to the instructions of the application you use. Note: This application is not compatible with all mobile device. FollowMe TV to DMR (optional) This feature allows video streaming from your TV to another TV or mobile devices, using proper applications (e.g. UPnP - Universal Plug and Play - applications like BubbleUPnP). Activate FollowMe TV to DMR and timeshifting starts. Press the red button and device selection menu will be displayed. Choose your device and press OK. Note: FollowMeTV and FollowMe TV to DMR features work correlated with the PVR feature and requires a connected USB storage device with FAT32 format and enough space in it. HD channels are not supported and both of the devices must be connected to the same network.

Media Playback via USB Input You can connect a 2.5” and 3.5” inch (hdd with external power supply) external hard disk drives or USB memory stick to your TV by using the USB inputs of the TV. IMPORTANT! Back up your files before making any connections to the TV. The Manufacturer will not be responsible for any file damage or data loss. Certain types of USB devices (e.g. MP3 Players) or USB hard disk drives/memory sticks may not be compatible with this TV. The TV supports FAT32 and NTFS disk formatting. While formatting a USB hard disk that has 1TB (Tera Byte) or more file capacity, you can experience problems with the formatting process. Quickly plugging and unplugging USB devices, is a very hazardous operation. This may cause physical damage to the USB player and the USB device itself. Do not pull out the USB module while playing a file.

You can use USB hubs with your TV’s USB inputs. External power supplied USB hubs are recommended in such a case.

It is recommended to use the TV’s USB input(s) directly, if you are going to connect a USB hard disk.

Show 5 more labels / short text on this page
Media Browser Menu · Loop/Shuffle Mode Operation · activate · activate · and activate
Page 9 of the Telefunken D48F275A3C user manual — To Switch the TV On
Page 9 · cliquer pour agrandir
Page 9

E-Manual (optional) You can find instructions for your TV’s features in the E-Manual. To use E-Manual, press to the Info button while main menu is displayed on the screen. By using the navigation buttons select a desired category. Every category includes a different topics. Select a topic and press OK to read instructions. To close the E-Manual screen press the Exit button.

Note: The contents of the E-Manual may vary according to the model. CEC and CEC RC Passthrough This function allows to control the CEC-enabled devices, that are connected through HDMI ports by using the remote control of the TV. The CEC option in the Other Settings menu under Settings menu should be set as Enabled at first. Press the Source button and select the HDMI input of the connected CEC device from the Source List menu. When new CEC source device is connected, it will be listed in source menu with its own name instead of the connected HDMI ports name(DVD Player, Recorder 1 etc.). The TV remote is automatically able to perform the main functions after the connected HDMI source has been selected. To terminate this operation and control the TV via the remote again, press and hold the “0-Zero” button on the remote control for 3 seconds. Or press Q.Menu button on the remote, highlight the CEC RC Passthrough and set as Off by pressing Left or Right button. This feature can also be enabled or disabled under the Settings/Other Settings menu. The TV supports also ARC(Audio Return Channel) feature. This feature is an audio link meant to replace other cables between the TV and the audio system (A/V receiver or speaker system). When ARC is active, TV does not mute its other audio outputs automatically. So you need to decrease TV volume to zero manually, if you want to hear audio from connected audio device only (same as other optical or co-axial digital audio outputs). If you want to change connected device’s volume level, you should select that device from the source list. In that case volume control keys are directed to connected audio device.

Page 10 of the Telefunken D48F275A3C user manual — Advanced Settings
Page 10 · cliquer pour agrandir
Page 10

TV Menu Features and Functions

Picture Menu Contents

Mode You can change the picture mode to suit your preference or requirements. Picture mode can be set to one of these options: Cinema, Game, Sports, Dynamic and Natural.

Contrast Sets the lightness and darkness values of the screen.

Brightness Sets the brightness value for the screen.

Sharpness Sets the sharpness value for the objects displayed on the screen.

Colour Sets the colour value, adjusting the colors.

Power Save Mode To set the Power Save Mode as Eco, Picture Off and Disabled.

(When the Mode is Dynamic, Power Save mode is automatically set as disabled.)

This setting controls the backlight level. The backlight function will be inactive if the Power Save Mode is set to Eco. The backlight cannot be activated in VGA, Media Browser mode or while the picture mode is set to Game.

If the broadcast signal is weak and the picture is noisy, use the Noise Reduction setting to reduce the amount of noise.

Advanced Settings

Dyanmic Contrast You can change the Dynamic Contrast ratio to desired value.

Colour Temp Sets the desired colour tone.

Picture Zoom Sets the desired picture size from picture zoom menu.

While watching from HDMI source, this feature will be visible in the Picture Settings menu. You can use this feature to enhance blackness in the picture.

Films are recorded at a different number of frames per second to normal television programmes. Turn this feature on when you are watching films to see the fast motion scenes clearly.

Skin Tone Skin tone can be changed between -5 and 5.

Colour Shift Adjust the desired colour tone.

RGB Gain You can configure the colour temperature values using the RGB Gain feature.

Reset Resets the picture settings to factory default settings.(Except Game Mode)

Autoposition (in PC mode) Automatically optimizes the display. Press OK to optimize.

H Position (in PC mode) This item shifts the image horizontally to the right hand side or left hand side of the screen.

V Position (in PC mode) This item shifts the image vertically towards the top or bottom of the screen.

Dot Clock (in PC mode)

Dot Clock adjustments correct the interference that appear as vertical banding in dot intensive presentations like spreadsheets or paragraphs or text in smaller fonts.

Depending on the resolution and scan frequency that you input to the TV set, you may see a hazy or noisy picture on the screen. In such a case you can use this item to get a clear picture by trial and error method.

Phase (in PC mode)

While in VGA (PC) mode, some items in Picture menu will be unavailable. Instead, VGA mode settings will be added to the Picture Settings while in PC mode.

Show 4 more labels / short text on this page
Backlight (Optional) · Noise Reduction · HDMI True Black · Film Mode
Page 11 of the Telefunken D48F275A3C user manual — Settings Menu Contents
Page 11 · cliquer pour agrandir
Page 11

Sound Menu Contents

Volume Adjusts the volume level.

Equalizer Selects the equalizer mode. Custom settings can be made only when in user mode.

Balance This setting is used for emphasizing left or right speaker balance.

Headphone Sets headphone volume.

Sound Mode You can select a sound mode. (If the selected channel supports).

AVL (Automatic Volume Limiting) Function sets the sound to obtain fixed output level between programmes.

When you connect an external amplifier to your TV using the headphone jack, you can select this option as Lineout. If you have connected headphones to the TV, set this option as Headphone.

Dynamic Bass Enables or disables the Dynamic Bass.

Surround Sound Surround sound mode can be changed as On or Off.

Digital Out Sets digital out audio type.

Settings Menu Contents

Conditional Access Controls conditional access modules when available.

Configures language settings (may change depending on the country selected) Preferred and current settings will be available. Current settings can be changed only if the broadcaster supports.

Enter correct password to change parental settings. You can easily adjust menu lock, maturity lock(may change depending on the country selected) and child lock in this menu. You can also set new pin number.

Timers Sets sleep timer to turn off the TV after a certain time. Sets timers for selected programmes.

Date/Time Sets date and time.

Sources Enables or disables selected source options.

Satellite Settings Displays satellite settings.

Network Settings (Optional) Displays network settings. (Optional)

Headphone/Lineout · Language · Parental

Page 12 of the Telefunken D48F275A3C user manual — Install and Retune Menu Contents
Page 12 · cliquer pour agrandir
Page 12

Other Settings: Displays other setting options of the TV set:

Menu Timeout Changes timeout duration for menu screens.

Scan Encrypted Channels When this setting is on, the search process will locate the encrypted channels as well.

HBB TV This feature is activated/deactivated by selecting ON/OFF.

Blue Background Activates or deactivates the blue background system when the signal is weak or absent.

Software Upgrade To ensure that your TV always has the most up to date firmware.

Application Version Displays application version.

Hard of Hearing Enables any special feature sent from the broadcaster.

Audio description refers to an additional narration track for blind and visually impaired viewers of visual media, including television and movies. You can use this feature, only if the broadcaster supports that additional narration track.

Auto TV Off You can set the timeout value of auto off feature. When the timeout value is reached and the TV has not been operated for a selected time, the TV will go into standby mode.

If the Standby Search is set to On, when the TV is in standby mode, available broadcasts will be searched. If the TV locates any new or missing broadcasts, a menu screen will be displayed, asking you whether or not to execute these changes. The Channel list will be updated and changed after this process.

Store Mode If you are displaying the TV in a store, you can activate this mode. Whilst Store Mode is enabled, some items in the TV menu may not be available.

Power Up Mode This setting confrigures the power up mode preference.

Biss is a satellite signal scrambling system that is used for some broadcasts. If you need to enter BISS key on a broadcast, you can use Biss Key setting located in the Other Settings menu. Highlight Biss Key and press OK to enter keys on the desired broadcast.

Install and Retune Menu Contents

Displays automatic tuning options. Digital Aerial: Searches and stores aerial DVB stations. Digital Cable: Searches and stores cable DVB stations. Analogue: Searches and stores analogue stations. Digital Aerial & Analogue: Searches and stores aerial DVB and analogue stations. Digital Cable & Analogue: Searches and stores cable DVB and analogue stations. Satellite: Searches and stores satellite channels.

Automatic Channel Scan (Retune)

Manual Channel Scan This feature can be used for direct broadcast entry.

Network Channel Scan Searches for the linked channels in the broadcast system.

Analogue Fine Tune You can use this setting for fine tuning analogue channels. This feature is not available if no analogue channels are stored.

First Time Installation Deletes all stored channels and settings, resets TV to factory settings.

Clear Service List (*) This setting is visible only when the Country option is set to Denmark, Sweden, Norway or Finland. Use this setting to clear channels stored.

CEC With this setting you can enable and disable CEC functionality completely. Press Left or Right button to enable or disable the feature.

Show 4 more labels / short text on this page
Audio Description · Standby Search (Optional) · Biss Key · (If available)
Page 13 of the Telefunken D48F275A3C user manual — Programme Options
Page 13 · cliquer pour agrandir
Page 13

General TV Operation

press the OK button. Then select “Delete Timer” option. The timer will be cancelled.

Using the Channel List

The TV sorts all stored stations in the Channel List. You can edit this channel list, set favourites or set active stations to be listed by using the Channel List options.

Connecting to a Wired Network

  • Connect broadband ISP connection ethernet cable to the ETHERNET INPUT of your modem.
  • Ensure that Nero Media Home software is installed to your PC.(for DLNA function). See Appendix A.

To prohibit viewing of certain programmes, channels and menus can be locked by using the parental control system.

To display parental lock menu options, the PIN number should be entered. After coding the correct PIN number, parental settings menu will be displayed.

  • Connect your PC to the one of your modem’s LAN connectors (e.g. LAN 1) by using a proper LAN cable.
  • Use another LAN output of your modem (e.g. LAN 2) to enable the connection to your TV.

Menu Lock: Menu lock setting enables or disables the menu access.

Maturity Lock: When set, this option gets the maturity information from the broadcast and if this maturity level is disabled, disables access to the broadcast.

Telefunken D48F275A3C — Connecting to a Wired Network diagram (page 13)
Fig. 3 · Connecting to a Wired Network

Child Lock: When Child Lock is set, the TV can only be controlled by the remote control. In this case the control panel buttons will not work.

Set PIN: Defines a new PIN number.

Electronic Programme Guide (EPG)

Some, but not all channels send information about the current and next programmes. Press the EPG button to view the EPG menu.

  • To access and play shared files, you must Select Media Browser. Press Menu button and select Media Browser. Press OK to continue. Select the desired file type and press OK. You must always use the Media Browser screen to access and play shared network files.

Up/Down/Left/Right: Navigate EPG.

OK: Displays programme options.

INFO: Displays, in detailed, information on the programme selected.

  • PC/HDD/Media Player or any other devices that are DLNA 1.5 compatible should be used with wired connection for higher playback quality.

GREEN: Switches to List Schedule EPG.

YELLOW: Switches to Timeline Schedule EPG.

To configure wired settings please refer Network Settings section in Settings menu.

BLUE: Displays filtering options.

Programme Options

  • You might be able to connect your TV to your LAN network depending on your network’s configuration. In such a case, use an ethernet cable to connect your TV directly to the network wall outlet.

In EPG menu, press the OK button to enter the Event Options menu.

In EPG menu, using this option, you can switch to the selected channel.

Set Timer / Delete Timer

After you have selected a programme in the EPG menu, press the OK button. Select the Set Timer on Event option and press the OK button. You can set a timer for future programmes. To cancel an already set timer, highlight that programme and

Show 6 more labels / short text on this page
Connectivity Functions · Configuring Parental Settings · Broadband ISP Connection · Lan(Ethernet cable) · Rear of TV · Select Channel
Page 14 of the Telefunken D48F275A3C user manual — IP Address
Page 14 · cliquer pour agrandir
Page 14
  • The transmission speed differs depending on the distance and number of obstructions between the transmission products, the configuration of these products, the radio wave conditions, the line traffic, and the products that you use. The transmission may also be cut off or get disconnected depending on the radio wave conditions DECT phones, or any other WiFi 11b appliances. The standard values of the transmission speed are the theoretical maximum values for the wireless standards. They are not the actual speeds of data transmission.
Telefunken D48F275A3C — Connecting to a Wireless Network diagram (page 14)
Fig. 4 · Connecting to a Wireless Network

Connecting to a Wireless Network

  • The location where the transmission is most effective differs depending on the usage environment.
  • Wireless LAN adaptor should be connected directly to the TV’s USB port. USB hubs are not supported.
  • To make your modem’s SSID visible, you should change your SSID settings via modem’s software. The TV cannot connect to the networks with hidden SSID.
  • You can plug your wifi dongle into the supplied USB extension cable In cases where network quality is poor and the wifi dongle needs to be placed to a location with better signal quality.

For connecting to a wireless LAN network, you should perform the following steps:

  • Wireless LAN adaptor supports 802.11 a,b,g & n type modems. It is highly recommended that you should use IEEE 802.11n communication protocol in order to avoid any possible problems while watching videos.
1. Connect broadband ISP connection ethernet cable to the ETHERNET INPUT of your modem.
2. Ensure that Nero Media Home software is installed to your PC (for DLNA function).
  • Use the other usb input, if you experience problems with audio/video performance.
  • You must change your modem’s SSID when there are any other modems around with the same SSID.
3. Afterwards, you should connect wireless adaptor to one of the USB inputs of the TV.

Configuring Network Settings Your TV’s Network Settings include Wired and Wireless Connection options. However, if your TV does not have USB Wi-Fi dongle, you should use Wired Connection type. If you try to connect via Wireless Connection when your TV does not have a USB Wi-Fi dongle, a warning screen will appear and the TV will not get an IP address. Try connecting the LAN cable after this and then the TV will be able to get an IP address. Configuring Wired Device Settings

4. To configure wireless settings please refer Network Settings section in the following sections.
Telefunken D48F275A3C — Connecting to a Wireless Network diagram (page 14)
Fig. 5 · Connecting to a Wireless Network

If you are connecting the TV via ETHERNET INPUT, select Network Type as Wired Device to configure.

Network Type

Network type can be selected as Wired or Wireless device, in accordance with the active connection to the TV set. Select this as Wired if you have connected to the TV a LAN cable. Select as Wireless if you connect via the wireless USB dongle.

  • A Wireless-N router (IEEE 802.11a/b/g/n) with simultaneous 2.4 and 5 GHz bands designed to increase bandwidth. Optimized for smoother and faster HD video streaming, file transfers, and wireless gaming.

Configuration Status

This section displays the status of the connection.

IP Address

If an active connection is available, the IP address will be displayed on this section. If you want to configure IP address preferences, press GREEN button and switch to the advanced mode.

  • Use LAN connection for quicker file sharing between other devices like computers.
  • The frequency and channel differ depending on the area.
Page 15 of the Telefunken D48F275A3C user manual — Delete Saved Wifi Profiles
Page 15 · cliquer pour agrandir
Page 15

Configuring Wired Network Settings in Advanced Mode

  • Afterwards, engage your cell phone with the router and then activate sharing software on your cell phone. Then, select files that you would like to share with your TV.
  • If the connection is established correctly, you should now access the shared files of your cell phone via the Media Browser of your TV.
  • Enter Media Browser menu and playback device selection OSD will be displayed. Select your cell phone’s ident and press OK to continue.

While in Advanced Mode, press RED button to edit settings. When finished, press OK to save, Press RETURN/BACK to cancel.

Wi-Fi feature can be used for a wireless network connection. If you have the Veezy 200 Wifi Dongle, select Network Type as Wireless Device to start connection process.

To enable Wi-Fi feature, profiles should be configured properly. Please plug in the Wi-Fi dongle to one of the USB ports.

Wireless Network Not Available

Ensure that the firewalls of your network allows the TV wireless connection. “Veezy 200” usb wifi dongle should be plugged properly (if available). If the wireless network does not function properly, try using the wired network in your home. Refer to the Wired Connection section for more information on the process.

Press YELLOW button to scan wireless network. Afterwards, available network list will be displayed. Please select your desired network from the list.

If the selected network is protected with a password, please enter the correct key by using the virtual keyboard. You can use this keyboard via navigation buttons and OK button on the remote control.

Check the modem (router) first. If the router does not have a problem, check the internet connection of your modem.Try searching for wireless networks again, using the Network Settings menu screen.

Wait until the IP the address is shown on the screen.

This means that the connection is now established. To disconnect from a wireless network, you should highlight Configuration Status and press OK.

Connection is Slow

See the instruction book of your wireless modem to get information on the internal service area, connection speed, signal quality and other settings. You need to have a high speed connection for your modem. Distruption during playback or slow reactions You could try the following in such a case: Keep at least three meters distance from microwave ovens, mobile telephones, bluetooth devices or any other Wi-Fi compatible devices. Try changing the active channel on the WLAN router. Using DLNA Network Service DLNA (Digital Living Network Alliance) is a standard that eases viewing process of digital electronics and makes them more convenient to use on a home network. For further information, visit www.dlna.org DLNA standard allows you to view and play photos, music and videos stored in the DLNA media server connected to your home network. Step 1: Nero Media Home DLNA function cannot be used if the server program is not install to your PC. Please prepare your PC with the provided Nero Media Home programme. For more information about the installation, please refer to Nero Media Home Installation section Step 2: Connect to a Wired or Wireless Network See the chapter Network Settings for detailed configuration information.

You can navigate between menu tabs by pressing left/ right buttons. The help bar on the bottom of the dialog shows features that you may use. Press BLUE button to check your internet connection speed.

You can check the signal strenght by using the network settings menu for the wireless device mode.

Information

Configuration Status: Displays wi-fi status as connected or not connected.

IP Address: Displays the current IP address.

Network Name: Connected networks’ name will be displayed.

Press GREEN button to switch to advanced mode and then press OK button to edit settings.

Delete Saved Wifi Profiles

  • Saved profiles will be deleted if you press red button while wireless device selection osd is on the screen. Connecting to your Cell Phone via WiFi (Optional)
  • If your cell phone has WiFi feature, you can connect your cell phone to your TV by using WiFi connection via a router, in order to play content from your phone. For this, your cell phone must have an appropriate sharing software.
  • Connect to your router following the steps stated above in the Wireless Connection section.

Connectivity Troubleshooting

Page 16 of the Telefunken D48F275A3C user manual — Internet Portal
Page 16 · cliquer pour agrandir
Page 16
3. Play Shared Files via Media Browser Select Media Browser by using Left or Right button from the main menu and press OK button. Media browser will be then displayed. DLNA support is available only with Media Browser folder mode. To enable folder mode, go to Settings tab in the main media browser screen and press OK . In the settings options, highlight View Style and change to Folder using Left or Right button.

First Time Installation for the proper operation of internet portal.

” button on your remote control and portal application options will be displayed. Application options will be displayed as the template below. Available applications’ contents may change depending on the application content provider.

Telefunken D48F275A3C — Note on PIP Window diagram (page 16)
Fig. 6 · Note on PIP Window

Please select desired media type and press OK. If sharing configurations are set properly, an OSD message will be displayed after selecting the desired media type. Select OK to display the selected network or USB memory content. If you want to refresh the device list, press GREEN button. You can press MENU to exit.

If available networks are found, they will be listed on this screen. Select media server or network that you want to connect by using “

” buttons and press OK button.

Note on PIP Window

If you switch to portal mode while watching TV channels, current programme will be displayed on the PIP window. You can change channels using P+/P- buttons.

If you select media type as Video and choose a device from the selection menu, a new menu screen will appear on the screen.

Select Videos from this screen to list all the available video files from the selected network.

Current HDMI content will be displayed on the PIP window, if you switch to portal mode while watching HDMI source.

To play other media types from this screen, you must go back to main Media Browser screen and select media type as desired and then perform the network selection again. Refer to Media Browser USB Playback section for further information on file playback.

Use the “ ” or “ ”, “ ” or “ ” to navigate between the items on Portal screen. Press the OK button to confirm your selection. Press the BACK button to go to the previous screen.

Subtitle files do not work if you watch video from network through DLNA.

Press the EXIT button to quit the Internet portal mode.

Appendix BHBBTV System

You can connect only one television with DLNA to same network. If a problem occurs with DLNA network, please switch on/off your television. Trick mode and jump are not supported with DLNA function.

HbbTV (Hybrid Broadcast Broadband TV) is a new industry standard that seamlessly combines TV services delivered via broadcast with services delivered via broadband and also enables access to Internet only services for consumers using connected TVs and set-top boxes. Services delivered through HbbTV include traditional broadcast TV channels, catch-up services, video-on-demand, EPG, interactive advertising, personalisation, voting, games, social networking and other multimedia applications.

CAUTION:

There may be some PC’s which may not be able to utilize the DLNA function due to administrator and security settings. (such as business PC’s).

For best home network streaming with this set, the supplied Nero software should be installed.

Internet Portal

HbbTV applications are available on channels where they are signalled by the broadcaster (currently various channels on Astra broadcast HbbTV applications). The broadcaster marks one application as “autostart” and this one is started by the platform automatically. The autostart applications are generally launched with a small red button icon to notify the user that there is an HbbTV application on that channel Press the red button to open the application page. After the page is displayed you can go back to the initial red button

You can access PORTAL mode using your TV. To do this, an active internet connection is required. Follow the steps on Connecting to a Wired/ Wireless(optional) Network section to connect your TV to internet. After the connection is established, you can select or view portal options.

Press “ · ” or “

Page 17 of the Telefunken D48F275A3C user manual — Tv will not turn on
Page 17 · cliquer pour agrandir
Page 17

icon state by pressing the red button again. You can toggle between the red button icon mode and full UI mode of the application via pressing red button. It should be noted that the red button switching capability is provided by the application and some application may behave differently.

numeric channel selection may not work on a teletect application where the numbers indicate teletext pages.

HbbTV requires AV streaming capability for the platform. There are numerous applications providing VOD (video on demand) and catch-up TV services. The user can use play, pause, stop, forward, and rewind keys on the remote control to interact with the AV content.

If you switch to another channel while an HbbTV application is active (either in red button icon mode or full UI mode), the following scenarios can occur.

  • The application can continue running.

Software Upgrade Your TV is capable of finding and updating automatically via the Aerial/Cable/Satellite signal. Software upgrade search via user interface Simply navigate on your main menu. Choose Settings and select Other Settings menu. In Other Settings menu navigate on to the Software for Upgrade item and press OK button. In Upgrade Options menu select Scan for upgrade and press OK button to check for a new software upgrade. If a new upgrade is found, it starts to download the upgrade. Press OK to continue with the reboot operation. 3 AM search and upgrade mode While the TV is connected to an aerial signal. If Automatic scanning in the Upgrade Options menu is Enabled, the TV wakes up at 03:00 and searches broadcast channels for new software upgrades. If new software is found and downloaded successfully, the next time the TV powers up, it will have the new software version. Note: If the TV fails to come on after the upgrade unplug the TV for 2 minutes and plug in again.

  • The application can be terminated.
  • The application can be terminated and another autostart red button application can be launched.

HbbTV allows the applications to be retrieved both from broadband or broadcast. The broadcaster may enable both ways or one of them. If the platfrom does not have an operational broadband connection, the platform can still launch applications transmitted on broadcast.

The autostart red button applications generally provide links to other applications. An example of this is shown below. The user then can switch to other applications by using the links provided. The applications should provide a way to terminate themselves, usually button 0 is used for this.

Telefunken D48F275A3C — Tv will not turn on diagram (page 17)
Fig. 7 · Tv will not turn on

Tv will not turn on

  • Make sure the power cord is plugged in securely to wall outlet. The batteries in the remote control may be exhausted. Press the Power button on the TV. Poor picture
  • Have you selected the correct TV system?
  • Low signal level can cause picture distortion.Please check antenna access.
  • Check if you have entered the correct channel frequency if you have done manual tuning.
  • The picture quality may degrade when two devices are connected to the TV at the same time. In such a case, disconnect one of the devices. No picture
  • No Picture means that your TV is not receiving a transmission. Have you selected the correct button on the remote control? Try once more. Also make sure the correct input source has been selected.
  • Is the antenna connected properly?
Figure aARD start bar application
Telefunken D48F275A3C — Tv will not turn on diagram (page 17)
Fig. 8 · Tv will not turn on

Figure b: ARD EPG application, broadcast video is shown on the left bottom, can be terminated by pressing 0.

HbbTV applications use keys on the remote control to interact with the user. When an HbbTV applications is launched, the control of some keys are owned by the application. For example,

  • Is the antenna cable damaged?

Troubleshooting & Tips

Page 18 of the Telefunken D48F275A3C user manual — Internet Connection Not Available / DLNA Mode Not Operating
Page 18 · cliquer pour agrandir
Page 18
  • Are suitable plugs used to connect the antenna?
  • If you are in doubt, consult your dealer.

No sound

  • Has the TV been set to mute? To cancel mute, press the “ ” button, or increase the volume level.
  • Sound is coming from only one speaker. Is the balance set to one extreme? See Sound Menu section.

Remote control - does not operate

  • The batteries may be exhausted. Replace the bateries.

Input sources - can not be selected

  • If you cannot select an input source, it is possible that no device is connected. if not
  • Check the AV cables and connections if you have tried to connect a device.

To install Nero MediaHome, please proceed as follows:

1. Enter the link below completely in the adressbar of your web browser.

http://www.nero.com/mediahome-tv

2. Click the Download button on the opening page. The installation file will be downloaded onto your PC.
3. After the download is completed, double click on the installation file to start the installation. The installation wizard will guide you through the installation process.

Internet Connection Not Available / DLNA Mode Not Operating

If the MAC address (a unique identifier number) of your PC or modem has been permanently registered, it is possible that your TV might not connect to the internet. In such a case, the MAC address is authenticated each time when you connect to the internet. This is a precaution against unauthorized access. Since your TV has its own MAC address, your internet service provider cannot validate the MAC address of your TV. For this reason, your TV cannot connect to the internet. Contact your internet service provider and request information on how to connect a different device, such as your TV, to the internet.

It is also possible that the connection may not be available due to a firewall problem. If you think this causes your problem, contact your internet service provider. A firewall might be the reason of a connectivity and discovery problem while using the TV in DLNA mode or while browsing via DLNA.

Nero MediaHome Installation

Page 19 of the Telefunken D48F275A3C user manual — Internet Browser
Page 19 · cliquer pour agrandir
Page 19

Internet Browser

To use the internet browser, please select the internet browser logo from the portal section.

Home Page Address Bar Add History Bookmarks Zoom

Telefunken D48F275A3C — Internet Browser diagram (page 19)
Fig. 9 · Internet Browser

Remote control shortcuts (Zoom in-out/Back/Home)

  • To navigate the web browser, use the arrow buttons on the remote control. Press OK to continue.

pages and these will take you to the appropriate pages.

  • After First time installation, predefined web sites and logos will be displayed on the browser’s access page (see image above). To add a desired web page to the quick access page, whilst on the website you wish to add, select the “Add” menu and select “Quick Access” button.
  • When you scroll the pointer down to the middle of the screen, the remote control’s shortcuts will be shown.
  • Use the zoom shortcut buttons or the zoom menu to zoom in or zoom out.
  • You can clear cookies or clear all browser data from the settings menu.
  • If you want to add bookmarks, select this item while the desired web page is on the screen.
  • Your TV is compatible with USB mice. Plug your mouse or wireless mouse adaptor to the USB input of your TV.
  • To view your browsing history, click the history button. You can also clear your browsing history from here.
  • You can navigate the web browser in three ways. First, enter any URL in the address bar.
Telefunken D48F275A3C — Internet Browser diagram (page 19)
Fig. 10 · Internet Browser
Telefunken D48F275A3C — Internet Browser diagram (page 19)
Fig. 11 · Internet Browser
  • The browser does not support multiple tabs.
  • Some internet pages include flash content. These are not supported by the browser.
  • You can search keywords by clicking the search button in the address dialog box or another way to navigate to pages is by clicking on links on web
  • Your TV does not support any download processes from the web browser.
Show 7 more labels / short text on this page
Refresh · Previous Next · Settings · Quick Access · Add · Bookmarks · Quick Access
Page 20 of the Telefunken D48F275A3C user manual — 1080P
Page 20 · cliquer pour agrandir
Page 20

PC Input Typical Display Modes The following table is an illustration of some of the typical video display modes. Your TV may not support all resolutions.

AV and HDMI Signal Compatibility

Source Supported Signals Available

PAL O

EXT

NTSC 60 O

(SCART)

RGB 50/60 O

1 640x350 85Hz 2 640x400 70Hz 3 640x400 85Hz 4 640x480 60Hz 5 640x480 66Hz 6 640x480 72Hz 7 640x480 75Hz 8 640x480 85Hz 9 800x600 56Hz 10 800x600 60Hz 11 800x600 70Hz 12 800x600 72Hz 13 800x600 75Hz 14 800x600 85Hz 15 832x624 75Hz 16 1024x768 60Hz 17 1024x768 66Hz 18 1024x768 70Hz 19 1024x768 72Hz 20 1024x768 75Hz 21 1024x768 85Hz 22 1152x864 60Hz 23 1152x864 70Hz 24 1152x864 75Hz 25 1152x864 85Hz 26 1152x870 75Hz 27 1280x768 60Hz 28 1360x768 60Hz 29 1280x768 75Hz 30 1280x768 85Hz 31 1280x960 60Hz 32 1280x960 75Hz 33 1280x960 85Hz 34 1280x1024 60Hz 35 1280x1024 75Hz 36 1280x1024 85Hz 37 1400x1050 60Hz 38 1400x1050 75Hz 39 1400x1050 85Hz 40 1440x900 60Hz 41 1440x900 75Hz 42 1600x1200 60Hz 43 1680x1050 60Hz 44 1920x1080 60Hz 45 1920x1200 60Hz

SECAM O

PAL 50/60 O

NTSC 60 O

SECAM

480I, 480P 60Hz O

576I, 576P 50Hz O

576I, 576P 50Hz O

HDMI 1

HDMI 2

24Hz, 25Hz, 30Hz, 50Hz, 60Hz

1080P

O

(XNot Available, O: Available)

In some cases a signal on the LCD TV may not be displayed properly. The problem may be an inconsistency with standards from the source equipment (DVD, Set-top box, etc. ). If you do experience such a problem please contact your dealer and also the manufacturer of the source equipment.

Show 9 more labels / short text on this page
Index Resolution Frequency · Side AV · YPbPr · 720P 50Hz,60Hz O · 1080I 50Hz,60Hz O · 480I 60Hz O · 480P 60Hz O · 720P 50Hz,60Hz O · 1080I 50Hz,60Hz O
Page 21 of the Telefunken D48F275A3C user manual — IMA-ADPCM/ MS-ADPCM
Page 21 · cliquer pour agrandir
Page 21

Supported File Formats for USB Mode

Media Extension Format Notes

Video.dat, .mpg, .mpeg

.ts, .trp, .tp, .m2ts

MPEG2 , H.264, VC1, AVS, MVC

H.264:1080Px2@25fps, 1080P@50fps MVC:1080P@ 24fps Other: 1080P@30fps - 50Mbit/sec

.vob MPEG2 1080P@30fps 50Mbit/sec

.mkv MPEG1-2-4, H.264

H.264:1080Px2@25fps, 1080P@ 50fps, 1080P@30fps, 50Mbit/sec

.mp4 MPEG4, XviD, H.264

H.264:1080Px2@25fps, 1080P@ 50fps, 1080P@30fps, 50Mbit/sec

.avi MPEG2-4, Xvid, H.264

H.264:1080Px2@25fps, 1080P@ 50fps, 1080P@30fps, 50Mbit/sec

.fla, .flv H.264, Sorenson H.263

H.264:1080Px2@25fps, 1080P@50fps, 1080P@30fps, 40Mbit/sec

.3gp MPEG4, H.264 1920x1080@30P 20Mbit/sec

.asf, .wmv VC1 1080P@30fps, 50Mbit/sec

Audio.mp3 MPEG1/2 Layer 1/2/3 (MP3) Layer1: 32Kbps ~ 448Kbps (Bit rate) / 16KHz ~ 48KHz (Sampling rate)

Layer28Kbps ~ 384Kbps (Bit rate) / 16KHz ~ 48KHz (Sampling rate)
Layer38Kbps ~ 320Kbps (Bit rate) / 16KHz ~ 48KHz (Sampling rate)

.wav LPCM

.WMA/ ASF

WMA, WMA Pro WMA128bps ~ 320Kbps (Bit rate) / 8KHz ~ 48Khz (Sampling rate)
WMA Pro< 768kbps (Bit rate) / ~ 96KHz (Sampling rate)

.m4a/ .aac AAC, HEAAC Free Format (Bit rate) / 8KHz ~ 48KHz (Sampling rate)

.pcm PCM 8Kbps ~ 320Kbps (Bit rate) / 16KHz ~ 48KHz (Sampling rate)

(works only with video files)

AC3 32Kbps ~ 640Kbps (Bit rate) / 32KHz, 44.1KHz, 48KHz (Sampling rate)

EAC3 32Kbps ~ 6 Mbps (Bit rate) / 32KHz, 44.1KHz, 48KHz (Sampling rate)

LPCM 64Kbps ~ 1.5Mbps (Bit rate) / 8KHz ~ 48Khz (Sampling rate)

IMA-ADPCM/ MS-ADPCM

384Kbps (Bit rate) / 8KHz ~ 48Khz (Sampling rate)

G711 A/mu-law 64~128Kbps (Bit rate) / 8KHz (Sampling rate)

Baseline Resolution(WxH)15360x8640, 4147200 bytes

.jpeg

Progressive Resolution(WxH)1024x768, 6291456 bytes
non-interlace Resolution(WxH)9600x6400, 3840000 bytes

.png

interlace Resolution(WxH)1200x800, 3840000 bytes
.bmp Resolution(WxH)9600x6400, 3840000 bytes

Subtitle.sub - Sub1, Sub2, Sub3

.srt -

Mpeg1-2 1080P@30fps, 50Mbit/sec · Picture

Page 22 of the Telefunken D48F275A3C user manual — MPEG2 , H.264, VC1, AVS, MVC
Page 22 · cliquer pour agrandir
Page 22

When connecting devices to your TV’s connectors by using DVI converter cable(DVI to HDMI cable - not supplied), you can refer to the following resolution information.

Telefunken D48F275A3C — MPEG2 , H.264, VC1, AVS, MVC diagram (page 22)
Fig. 12

Supported DVI Resolutions

Sources

Références et liens

Pages mentionnées dans ce manuel — fabricant, assistance et téléchargements.

Poser une question sur : Telefunken D48F275A3C

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Telefunken D48F275A3C

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Telefunken D48F275A3C manuel PDF

77 pages·7.3 MB·Téléviseur LED·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…