Manuel d'utilisation / d'entretien du produit P-61-743 du fabricant ADC
Aller à la page of 30
ADCP-61-743 • Issue 3 • September 2004 1304058 Page 1 2004, ADC Telecommunications, Inc. Soneplex ® Remote Test Access Unit (RTAU) User Manual ) Content Page 1 DESCRIPTION ......................................................................
ADCP-61-743 • Issue 3 • September 2004 Page 2 2004, ADC Telecommunications, Inc. Related Publications Listed below are related manuals and their pub lication numbers. Copies of these publications can be ordered by contacting the ADC Technical Assistance Center at 1-800-366-3891.
ADCP-61-743 • Issue 3 • September 2004 Page 3 © 2004, ADC Telecommunications, Inc. FCC Compliance Statement The Remote Test Access Unit has been certified to comply with the requirements for Class A computing devices per part 15 of the FCC regulations.
ADCP-61-743 • Issue 3 • September 2004 Page 4 2004, ADC Telecommunications, Inc. 1 DESCRIPTION The Remote Test Access Unit (RTAU) (Figur e 1) provides maintenance functionality for monitoring and intrusive test access to the DS1 channels in the chassis between the DS3 MUX and the low speed distribution modules (DLX, HLXC, ODS2, and RLX).
ADCP-61-743 • Issue 3 • September 2004 Page 5 © 2004, ADC Telecommunications, Inc. 11897-A RTAU STATUS LINE CODE INTRUSIVE TEST B8ZS AMI BIPOLAR ACCESS D S 1 RX TX Figure 1.
ADCP-61-743 • Issue 3 • September 2004 Page 6 2004, ADC Telecommunications, Inc. 1.1 DS3 MUX Compatibility Refer to Table 1 for compatibility informati on for DS3 MUXs, test access units, and MPU/SCU software versions.
ADCP-61-743 • Issue 3 • September 2004 Page 7 © 2004, ADC Telecommunications, Inc. 2.1 Initial Installation This installation procedure applies to the firs t time an IBBC shelf will be populated with a RTAU module. If the IBBC shelf has alrea dy been populated with a RTAU module, go to 2.
ADCP-61-743 • Issue 3 • September 2004 Page 8 2004, ADC Telecommunications, Inc. 14185-A RTAU MODULE HSW HSP TAU APU SCU MXP MXW DS3 FAIL RESET LMPTST/ APS LPBK ENABLE ONLINE STATUS APS LOCKOU.
ADCP-61-743 • Issue 3 • September 2004 Page 9 © 2004, ADC Telecommunications, Inc. 2.2 Maintenance Installation (Existing System) Replacement of the RTAU module in existing IBBC shelves should follow normal maintenance procedures.
ADCP-61-743 • Issue 3 • September 2004 Page 10 2004, ADC Telecommunications, Inc. 3 LED CHECK 1. When the RTAU module (Figure 3) is seated, the STATUS LED will be lit red for approximately 5 seconds. All LEDs will then flash yellow, and then the STATUS LED will be lit green.
ADCP-61-743 • Issue 3 • September 2004 Page 11 © 2004, ADC Telecommunications, Inc. 4 FRONT PANEL OPERATION All controls and indicators of the RTAU includi ng the jack accesses for a selected DS1 signal are located on the front panel (Figure 3). The cont rols and indicators are described in Table 2.
ADCP-61-743 • Issue 3 • September 2004 Page 12 2004, ADC Telecommunications, Inc. 5 CONFIGURATION Use this menu to view or edit the configuration for the RTAU module after it is installed in the chassis. This menu can also be used to equip, provision, assign thresholds, and assign service state.
ADCP-61-743 • Issue 3 • September 2004 Page 13 © 2004, ADC Telecommunications, Inc. 5. Use the arrow or number keys to select RTAU Setup and Control from the RTAU Configuration menu. Press Enter or Return . The RTAU Setup and Control screen will appear as shown in Figure 6.
ADCP-61-743 • Issue 3 • September 2004 Page 14 2004, ADC Telecommunications, Inc. SYSTEM MAINTENANCE 1. Force/APS Commands 2. Reset/LED Test Commands 3. Execute ACO (Alarm Cutoff) 4. Loopback Status/Commands 5. Display Inventory 6. Display Circuit IDs 7.
ADCP-61-743 • Issue 3 • September 2004 Page 15 © 2004, ADC Telecommunications, Inc. 7. Assign the selections by pressing Enter or Return. RTAU SETUP AND CONTROL EQUIPMENT SETUP =============== Cu.
ADCP-61-743 • Issue 3 • September 2004 Page 16 2004, ADC Telecommunications, Inc. Table 3. RTAU Configurati on Fields FIELD TYPE OPTIONS DESCRIPTION DEFAULT EQUIPMENT SETUP FIELDS Current User Toggle OV E R V IE W : T h e C u r r en t U s e r f i el d c a n o n l y b e set to NONE or CRAFT from the Craft menu.
ADCP-61-743 • Issue 3 • September 2004 Page 17 © 2004, ADC Telecommunications, Inc. Table 3. RTAU Configurati on Fields, continued FIELD TYPE OPTIONS DESCRIPTION DEFAULT EQUIPMENT SETUP FIELDS, c.
ADCP-61-743 • Issue 3 • September 2004 Page 18 2004, ADC Telecommunications, Inc. Table 3. RTAU Configurati on Fields, continued FIELD TYPE OPTIONS DESCRIPTION DEFAULT EQUIPMENT SETUP FIELDS, .
ADCP-61-743 • Issue 3 • September 2004 Page 19 © 2004, ADC Telecommunications, Inc. Table 3. RTAU Configurati on Fields, continued FIELD TYPE OPTIONS DESCRIPTION DEFAULT SIGNAL GENERATOR SETUP FI.
ADCP-61-743 • Issue 3 • September 2004 Page 20 2004, ADC Telecommunications, Inc. Table 3. RTAU Configurati on Fields, continued FIELD TYPE OPTIONS DESCRIPTION DEFAULT SIGNAL GENERATOR SETUP FIELDS, continued Pattern Type, continued Toggle 1 in 8 Containi ng strings of 7 sequential 0’s.
ADCP-61-743 • Issue 3 • September 2004 Page 21 © 2004, ADC Telecommunications, Inc. Table 3. RTAU Configurati on Fields, continued FIELD TYPE OPTIONS DESCRIPTION DEFAULT SIGNAL GENERATOR SETUP FI.
ADCP-61-743 • Issue 3 • September 2004 Page 22 2004, ADC Telecommunications, Inc. Table 3. RTAU Configurati on Fields, continued FIELD TYPE OPTIONS DESCRIPTION DEFAULT BIT ERROR SETUP FIELDS OVERVIEW: Bit errors can be injected by th e RTAU using the Bit Error Set Up fields.
ADCP-61-743 • Issue 3 • September 2004 Page 23 © 2004, ADC Telecommunications, Inc. Table 3. RTAU Configurati on Fields, continued FIELD TYPE OPTIONS DESCRIPTION DEFAULT Elapsed Time ES Display only None Six-digit counter or blank. Blank Elapsed Time EFS Display only None Six-digit counter or blank.
ADCP-61-743 • Issue 3 • September 2004 Page 24 2004, ADC Telecommunications, Inc. DS3 MUX RT A U P A TTERN GEN DETECT OR CONTROLLER A B MPU or SCU LINE CARD DS1 TEST SET RX TX BIPOLAR A CCESS RT AU FRONT P ANEL DS3 EQUIPMENT MONIT OR SPLIT DS1 F ACILITY 11864-C Figure 8.
ADCP-61-743 • Issue 3 • September 2004 Page 25 © 2004, ADC Telecommunications, Inc. DS3 MUX RT AU AB EQUIPMENT (E) [NETWORK] F A CILITY (F) [CUST OMER] CIRCUIT UNDER TEST TEST SIGNAL GENERA T OR .
ADCP-61-743 • Issue 3 • September 2004 Page 26 2004, ADC Telecommunications, Inc. A END INTEROFFICE F ACILITY CPE INSERT : NETWORK DROP: NETWORK FE 11868-B Z END CPE SPL TE RT AU QRS B = ".
ADCP-61-743 • Issue 3 • September 2004 Page 27 © 2004, ADC Telecommunications, Inc. SPL TF INSERT : NETWORK DROP: CUST OMER INSERT : CUST OMER FE QRS A END CPE RT AU INTEROFFICE F ACILITY Z END C.
ADCP-61-743 • Issue 3 • September 2004 Page 28 2004, ADC Telecommunications, Inc. DS3 MUX RT AU A B A B EQUIPMENT (E) [NETWORK] F A CILITY (F) [CUST OMER] CIRCUIT UNDER TEST SIGNAL PRESENCE DE.
ADCP-61-743 • Issue 3 • September 2004 Page 29 © 2004, ADC Telecommunications, Inc. Table 4. TL1 Commands Used for the RTAU COMMAND DESCRIPTION CHG-ACCMD-T1 Change Access Mode T1 CHG-LPBK-T1 Chan.
ADCP-61-743 • Issue 3 • September 2004 Page 30 8 CUSTOMER INFORMATION AND ASSISTANCE ADC Technical support is available 24 hours a day, 7 days a week by contacting the ADC Technical Assistance Center. Sales Assistance 800.366.3891 • Quotation Proposals • Ordering and Deli very • General Product Informati on Systems Integration 800.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté ADC P-61-743 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du ADC P-61-743 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation ADC P-61-743, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le ADC P-61-743 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le ADC P-61-743, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du ADC P-61-743.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le ADC P-61-743. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei ADC P-61-743 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
