Manuel d'utilisation / d'entretien du produit GT-20 GT-222 du fabricant Boston Acoustics
Aller à la page of 19
GT-20 GT-22 2-Channel, High-Curr ent/High-Power Amplifiers.
2 T able of Contents Parts List 3 Features and Specifications 3 Control Functions 4 Control functions (cont.) 5 Mechanical Functions 6 Recessed RCA inputs 6 Control cover r emoval & reinstallation 6 Multi-position mounting feet 6 V ents (side & rear) 6 Mechanical functions (cont.
Included Hardwar e: GT -20 & GT -22 (1) owner’ s manual (1) female quick-connect terminal (1) 2mm hex wrench (for speaker input) (1) 3mm hex wrench (for power input) (4) mounting screws 3 Parts List Te chnical Specifications GT -20 GT -22 14.
4 Contr ol Functions RCA Inputs RCA cables from head unit or fr om other line level device should be connected here. Use both inputs (L & R) for ster eo; use “L” input for mono. Remote Input Use the supplied FEMALE quick-connector to connect the REMOTE trigger lead from the head unit to the amplifier .
5 Contr ol Functions (cont.) Lowpass Crossover Contr ols To use 12dB/octave crossover , move switch to right-hand position. Lowpass crossover fr equency is adjustable from 50Hz to 350Hz by r otary control. (Moving switch to left-hand position will bypass crossover functions.
6 Mechanical Functions Recessed RCA Inputs The input jacks are r ecessed into the body of the amplifier to provide clear- ance in tight mounting locations. Control Cover Removal & Reinstallation The cover panel is secured with two (2) captive coin-slotted scr ews.
7 Mechanical Functions (cont.) Amplifier Linking The design of the side panels enables multiple amplifiers to be used together without additional hardwar e. Wire Connection Amplifier accepts stripped wire dir ectly into the terminal blocks. Speaker outputs accept 8-gauge, and the DC power and ground accept 4-gauge.
8 Before Y ou Install Before you install the unit, disconnect the negative (–) battery cable in the engine compartment of the vehi- cle. Doing so will prevent damage to both the electrical system of the vehicle and the amplifier during installation.
9 57mm (2.5") Choose the Mounting Location Plan your installation so that the amplifier is mounted where adequate ventilation is available. Never mount an amplifier in the engine compartment of a vehicle! W ARNING! Before driving the mounting scr ews thr ough any surface, be sure of what is behind that sur- face.
10 Passenger & T runk Compartment Mounting If the amplifier is mounted under a seat, be sure that the vents do not become blocked. Do not allow seat padding or other obstructive material to press down on the amplifier . All Boston GT amplifiers have top panel controls.
Power/B+ & Power/GND Connection Strip approximately 5 / 8 " (16mm) of insulation. The positive (+) power wir e is installed into the amplifier terminal marked “B+”. The negative (–) wire is installed into the terminal marked “GND”.
12 Mono Subwoofer Operation When the amplifier is configured for mono operation, use the speaker output terminals marked for mono use. W ARNING! Subwoofer impedance must not fall below 2 ohms when in MONO mode. Installation—Fuses & Wiring (cont.
13 Setup T uning—Full-range Speakers (cont.) 4) Head Unit The head unit should have all controls such as bass, tr eble, balance, and fader set to the flat or centered position.
14 8) “Q” Control Once the highpass crossover point has been determined, use the “Q” contr ol to increase the bass information center ed around the cr ossover point. Setting the “Q” control is done in conjunction with setting the levels on the input sensitivity and highpass crossover fr equency controls.
15 4) Input Sensitivity Control Tu rn contr ol all the way counterclockwise (minimum position). In this position, the amplifier will be less sen- sitive to the input signal from the head unit. Slowly r otate this control clockwise until maximum undistorted playing level is heard fr om the subwoofer(s).
16 System Examples System A—Full-range Front Speakers fuse to + battery terminal to ground 6 . 5 L F 6 . 5 L F System B—Rear Fill Speakers fuse to + battery terminal to ground 6 .
17 System Examples (cont.) System C—Single Subwoofer (2 Ω ) System D —Parallel 4 Ω Subwoofers (2 Ω load) fuse to + battery terminal to ground 10.
18 Amplifier T r oubleshooting Guide Status LEDs on Amplifier not Lit — Head Unit (Sour ce) T urned “ON” V erify Remote turn-on wire fr om source to amplifier has pr oper voltage Power (B+) c.
19 Contact and W arranty Information 300 J ubilee Drive Pe a b o d y, MA 0 1 960 U.S.A. (978) 538-5000 Boston, Boston Acoustics, and the Boston logo are r egister ed trademarks of Boston Acoustics, Inc. © 2003 Boston Acoustics, Inc. All rights reserved.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Boston Acoustics GT-20 GT-222 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Boston Acoustics GT-20 GT-222 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Boston Acoustics GT-20 GT-222, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Boston Acoustics GT-20 GT-222 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Boston Acoustics GT-20 GT-222, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Boston Acoustics GT-20 GT-222.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Boston Acoustics GT-20 GT-222. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Boston Acoustics GT-20 GT-222 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
