
Before first using the machine,
please read this instruction manual carefully, for your own safety and for the safety of others. Keep the manual in a safe place and pass it on to any subsequent owner to en- sure that the information contained therein is available at all times. Failure to adhere to the safety instructions and directions may result in electric shock, fire, and/or serious injury.
Intended purpose 139 Notes on safety 139
Symbols used on the saw 140 Symbols used in the instructions... 140 General safety instructions for power tools 140 General description 144
Function description 144 Overview 144 Safety functions 144 Delivery contents 145 Operation startup 145
Assemble the blade 145 Assemble the saw chain 145 Tensioning the saw chain 146 Chain lubrication 146 Operating the chainsaw 146
This electric chainsaw is to be used only by one person and only for sawing wood. Materials such as plastic, stone, metal or wood containing foreign objects (e.g. nails or screws) must not be machined. The chainsaw is designed for employment in the do-it-yourselfer sector. It was not designed for continuous employment in the commercial sector. The device is designed for use by adults. Young people over 16 years old may use the chainsaw under supervision only. The manufacturer is not liable for damages, which were caused through use in appli- cations for which it was not designed, or incorrect operation.
Switching on 147 Checking the chain brake 147 Checking the oil automatic system... 147 Sawing techniques 148
General 148 Bucking 148 Felling trees 149 Maintenance and cleaning 151
Cleaning 151 Maintenance intervals 151 Maintenance Interval Table 151 Oiling the saw chain 151 Sharpening the saw chain 152 Adjusting the chain tension 153 Starting up a new saw chain 153 Maintaining the chain bar 153 Waste disposal and environmental protection 154 Spare parts 154 Technical Data 154 Guarantee 155 Repair service 155 Translation of the original EC declaration of conformity 197 Exploded Drawing 198 Grizzly Service-Center 199
This section deals with the basic safety regulations while working with the electric chainsaw.
An electric chainsaw is a dangerous
device, which can cause serious or even fatal injuries with incorrect or careless use. Thus, for your own safety and the safety of others, you should always take note of the in- structions on safety and, in case of

difficulties, consult a specialist for advice.
Symbol on the oil filler cap:
Indication on oil filler neck
Symbols used on the saw
Symbol on the fixing screw for the chain wheel cover:
Read and take note of the operating
Open Closed Symbols used in the instruc- tions
manual belonging to the machine!
spring-back of the machine during work.
Hazard symbols with informa-
tion on prevention of personal injury and property damage.
Do not expose the unit to rain. The
device must not be wet, nor should it be operated in a moist environ- ment.
Precaution symbol (explanation of
precaution instead of exclamation mark) with information on prevention of harm / damage.
ately from the plug socket in case of damage or cutting through of the mains cable
how to handle the device properly.
General safety instructions for power tools
Wear personal protective equip-
ment. Basically, wear protective goggles or, even better, face protec- tion, safety helmet, cut-protection working clothes and ear protection.
tions and instructions. Omis- sions in the compliance with safety directions and instructions can cause electrical shock, fire and/or severe injuries.
Wear cut-protection gloves.
Wear cut-protection safety boots with anti-slip soles.
Retain all safety directions and instruc- tions for future use.
Sound power level guaranteed
The term “Power Tools” used in the safety instructions refers to mains-operated power tools (with power cord) and to bat- tery- operated power tools (without power cord).
Length of the chain bar
Machines do not belong with do-
mestic waste.
dB · Safety class II

dual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. Use a surge protector with a release current of 30 mA or less.
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents. b) Do not operate power tools in ex-
plosive atmospheres, such as in the presence of flammable Iiquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away
a) Stay alert, watch what you are do-
ing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alco- hol or medication. A moment of inat- tention white operating power tools may result in serious personal injury. b) Use personal protective equipment.
while operating a power tool. Dis- tractions can cause you to lose control.
a) Power tool plugs must match the
Always wear eye protection. Protec- tive equipment such as dust mask, non- skid safety shoes, hard hat, or hearing protection used for appropria te condi- tions will reduce personal injuries. c) Prevent unintentional starting.
outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or
Ensure the switch is in the off-po- sition before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. d) Remove any adjusting key or
grounded surfaces, such as pipes, ra- diators, ranges and refrigerators. The- re is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain
or wet conditions. Water entering a power tool will increase the risk of elec- tric shock. d) Do not abuse the cord. Never use
wrench before turning the power tool on. A wrench or a key left at- tached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper
the cord for carrying, pulling or un- plugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entan opergled cords increase the risk of electric shock. e) When operating a power tool out-
footing and balance at all times. This enables better control of the power tool in unexpected situations. . f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewel- lery or long hair can be caught in mov- ing parts.. g) If devices are provided for the con-
doors, use an extension cord sui- table for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is unavoidable, use a resi-

nection of dust extraction and col- lection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust- related hazards. h) Warning! During operation, this electric
parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less Iikely to bind and are easier to control. g) Use the power tool, accessories
tool generates an electromagnetic field which, under certain circumstances, may impair the functionality of active or passive medical implants. To reduce the risk of serious or lethal injuries, we recommend that persons with medical implants consult their doctor and the manufacturer of their medical implant before operating the machine.
and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations differ- ent from those intended could result in a hazardous situation. h) If the power cable for this equipment is
a) Do not force the power tool. Use
the correct power tool for your ap- plication. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the
damaged, it must be replaced by the manufacturer, a customer service agent of the same or a similarly qualified per- son in order to prevent hazards.
switch does not turn it on and off. Any power tool that cannot be con- trolled with the switch is dangerous and must be repaired. c) Disconnect the plug from the pow-
a) Have your power tool serviced by
a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
er source and/or the battery pack from the power tool before making any adjustments, changing acces- sories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool ac- cidentaIly. d) Store idle power tools out of the
a) Keep all parts of the body away from
the saw chain when the chain saw is operating. Before you start the chain saw, make sure the saw chain is not contacting anything. A moment of inattention white operating chain saws may cause entanglement of your cloth- ing or body with the saw chain. b) Always hold the chain saw with
reach of children and do not allow persons unfamiliar with the power tool or these instructions to oper- ate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for
your right hand on the rear handle and your left hand on the front
misalignment or binding of moving

handle. Holding the chain saw with a reversed hand configuration increases the risk of personal injury and should never be done. c) Wear safety glasses and hear-
chance for kickback. k) Keep handles dry, clean, and free
from oil and grease. Greasy, oily handles are slippery causing loss of control.. l) Cut wood only. Do not use chain saw for purposes not intended. For example: do not use chain saw for cutting plastic, masonry or non- wood building materials. Use of the chain saw for operations different than intended could result in a hazardous situation. m) Hold the power tool only on the in-
ing protection. Further protective equipment for head, hands, legs and feet is recommended. Adequate protective clothing will reduce person- al injury by flying debris or accidentaI contact with the saw chain. d) Do not operate a chain saw in a
tree. Operation of a chain saw white up in a tree may result in personal in jury. e) Always keep proper footing and
sulated handle surfaces, as the saw chain can come into contact with concealed power lines or the mains cable to the equipment. Contact between the saw chain and a live wire can make metal parts of the equip- ment live and cause an electric shock.
operate the chain saw only when standing on fixed, secure and level surface. Slippery or unstable surfaces such as ladders may cause a loss of balance or control of the chain saw. f) When cutting a Iimb that is under tension be alert for spring back. When the tension in the wood fibres is released the spring loaded Iimb may strike the operator and/or throw the chain saw out of control. g) Use extreme caution when cutting
Beware of kickback! Be careful of
kickback of the machine during work. There is danger of injury here. You can avoid kickbacks by exercising caution and using a cor- rect sawing technique.
brush and saplings. The slender material may catch the saw chain and be whipped toward you or pull you off balance. h) Carry the chain saw by the front
Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a sud- den reverse reaction, kicking the guide bar up and back towards the operator Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator. Either of these reactions may cause you to lose control of the saw which could result in serious personal injury. Do not rely exclu-
handle with the chain saw switched off and away from your body. When transporting or storing the chain saw always fit the guide bar cover. Proper handling of the chain saw will reduce the Iikelihood of accidentaI contact with the moving saw chain. i) Follow instructions for lubricating, chain tensioning and changing ac- cessories. Improperly tensioned or lubricated chain may either break or increase the

sively upon the safety devices built into your saw. As a chain saw user, you should take several steps to keep your cutting jobs free from accident or injury. Kickback is the result of tool misuse and/ or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below: a) Maintain a firm grip, with thumbs
user. Refer to the following descriptions for the function of control elements.
The diagrams for the operation of the device can be found on pages 2 + 3.
and fingers encircling the chain saw handles, with both hands on the saw and position your body and arm to allow you to resist kickback forces. Kickback forces can be controlled by the operator, if proper precautions are taken. Do not let go of the chain saw b) Do not overreach and do not cut
1 Rear handle 2 Oil filler cap 3 Oil tank cap 4 Chain brake handle, front hand guard 5 Chain bar (Guide rail) 6 Saw chain 7 Nose sprocket 8 Bumper 9 Front handle 10 Electric motor 11 On/off switch 12 Safety lock 13 Chain catcher 14 Chain adjustment ring 15 Safety bolt 16 Sprocket chain wheel covering 17 Rear hand guard 18 Cable holder 19 Mains cable 20 Saw bar protection sheath
above shoulder height. This helps pre- vent unintended tip contact and enables better control of the chain saw in unex- pected situations.. c) Only use replacement bars and
chains specified by the manufac- turer. Incorrect replacement bars and chains may cause chain breakage and/ or kickback. d) Follow the manufacturer´s sharpen-
ing and maintenance instructions for the saw chain. Decreasing the depth gauge height can lead to in- creased kickback.
1 Rear grip with hand guard
Protects the hand against branch- es and boughs in the case of springing away by the chain. 4 Chain braking lever/hand guard Control system, which stops the
The chainsaw is driven by an electric mo- tor. The circulating chain is led around a saw bar (guide rail) The tool is fitted with a rapid-action chain- tensioning system and a fast-acting chain brake. An automatic oil dosing regulator ensures continuous chain lubrication. The chainsaw is equipped with various protection fittings for the protection of the
saw chain immediately in case of a spring-back; lever can also be activated manually; protects the left hand of the operator if it slides from the front grip. 6 Saw chain with small spring-
Overview · Safety functions · Function description

back Helps you to catch spring-backs
with specially developed control systems. 8 Metal stop claw Reinforces the stability when
Please note that the saw re-oils after use and oil may leak out if it is stored on its side or on the head. This is a normal process due to the necessary ventilation opening on the upper edge of the tank and does not constitute a reason for complaint. As each saw is checked during production and tested with oil, a small residue may be in the tank despite draining, which may slightly dirty the housing with oil in transit. Please clean the housing with a cloth.
vertical cuts are carried out and facilitates sawing. 10 Electric motor Double insulated for safety rea-
sons. 11 On-off switch with safety chain brake On releasing the On/Off switch, the
device immediately switches off. 12 Switch-on block The switch-on block must be re- leased for switching on the device. 13 Chain catcher Decreases the danger of injuries if the chain breaks or if it comes off.
- Chainsaw - Blade (guide rail) - Saw chain - Protective blade holder - 180 ml Grizzly bio oil - Instruction Manual
Assemble the saw chain
so the cutting edges face clock- wise (6). 2. Place the chain around the chain cog (22) and insert into the blade groove. It is normal for the saw chain to sag. 3. Pretension the chain by turning the tensioning screw (21) clock- wise. 4. Attach the chain wheel cover (16). Here, the lug on the cover must initially be inserted into the notch provided on the device for this purpose (23). Tighten the fix- ing screw (15) only slightly, as the saw still has to be tensioned.
Always wear protective gloves
when working with the chainsaw and employ only original parts. Pull out the power plug before doing any work on the chainsaw itself -– injury hazard!
Before initial operation of the electric chain- saw, you must assemble the blade, chain and chain wheel cover, adjust the chain, fill with chain oil, check the function of the chain brake and check the oil mechanism.
Assemble the blade · Delivery contents

Tensioning the saw chain
since the chain becomes blunt faster. You can identify a case of too little oil where smoke develop- ment or discoloration of the rail occurs.
With a correctly tensioned chain you get good cutting performance and a longer life.
An incorrectly tensioned chain
may break or spring off, leading to danger of injury. Test the elec- tric saw before every start and the chain tension after every hour of sawing
The power saw is equipped with an oil automatic system. As soon as the motor is speeded up, the oil also flows faster to the chain bar.
Fill with chain oil
The chain is correctly tensioned if it does not sag at the rail underside and can be rotated completely around with the gloved hand. When the saw chain is tensioned with 9 N (approx. 1 kg), the gap between the saw chain and the guide rail may not be more than 2 mm.
been released, that is, that the chain brake lever (4) is pulled up against the front grip. 2. Unscrew the fastening bolt (15). 3. To tighten the saw, turn the chain adjustment ring (14) clockwise. To loosen the tension, turn the chain adjustment ring anti- clockwise. 4. Tighten up the fastening bolt (15) again.
Always switch off the device
and allow the motor to cool be- fore filling with chain oil. There is a risk of fire if oil overflows.
With a new saw chain, you must
readjust the chain tension after at least 5 cutting operations.
Switch on the chainsaw only when
chain bar, saw chain and sprocket chain wheel covering are correctly assembled. Ensure the voltage of the mains connection agrees with the label on the device. Make sure you have a secure
The rail and chain must never be
without oil. If you operate the elec- tric chainsaw with too little oil, the cutting performance and the life- time of the saw chain is reduced,
Chain lubrication

stance. Before starting, ensure that the electric chainsaw is in contact with no objects.
against the front grip. 2. Place the electric chainsaw onto a solid, flat surface. It must not contact any objects. 3. Connect the device to the mains voltage. 4. Hold the electric chainsaw firmly with both hands, with the right hand on the rear grip and the left hand on the front handle. Thumb and finger must close securely over the handles. (see ). 5. Turn on the electric chainsaw. (See “Switching On”). 6. Activate the chain braking lever (4), with running motor, with the left hand. Chain should stop abruptly.. 7. Once the chain brake is work- ing properly, release the on/off switch and the chain brake.
Check before the start, whether
sufficient chain oil is in the tank and, if necessary, refill with chain oil (see Chapter Operation Start).
you shift the brake arm (4) back against the front grip.. 2. Form a loop from the end of the extension cable and hang this into the tension relief (18) on the rear grip. 3. Connect the device to the mains voltage 4. Hold the electric chainsaw firmly with both hands, with the right hand on the rear grip and the left hand on the front handle. Thumb and finger must close securely over the handles. 5. For switching on, activate the switch-on block (11) with the right thumb and then press the On/Off switch (10), the electric power saw runs with highest speed. Release the switch-on block again. 6. The power saw switches off when you release the On/Off switch again. Switching for con- tinuous running is not possible
If the chain brake does not func-
tion correctly, you must not use the electric chainsaw. A slack saw chain leads to danger of in- jury. Return the electric chainsaw to our Service-Center for repair
Checking the oil automatic sys- tem
Check the oil level and the oil automatic system before commencement of work. • Switch on the chainsaw and hold it above a bright background. The saw must not touch the ground.
Checking the chain brake
If an oil trace can be seen, the chainsaw is working trouble-free.
The saw chain does not turn if the
chain brake is engaged.
Oils can become viscous in cold
weather.
shifting the brake arm (4) over
Switching on

If no trace of oil appears, it may
be necessary to clean the oil out- let channel or to have the electric chainsaw repaired by our customer service.
If the saw chain jams, you
Observe the noise protection and lo-
do not attempt to pull out the electric chainsaw using power. There is a danger of injury here. Switch off the motor and use a lever or wedge to free the elec- tric chainsaw.
cal regulations when cutting wood. Local requirements may require a suitability test. Ask the forestry com- mission.
This refers to sawing up a felled tree trunk into smaller sections.
Saw through the log completely from above and ensure at the end of the cut not to contact the ground. If you can turn the tree trunk, saw
two-thirds of the way through it. Then turn the trunk around and saw the rest of the way through from above. 2. Log is supported at one end:
Start sawing from the bottom and work your way up (with the upper edge of the bar) a third of the way
General · Bucking

into the diameter of the trunk to prevent splitting. Then saw from the top downwards with the lower edge of the bar towards the first cut to prevent the bar from be- coming jammed in the wood.. 3. Log is supported at both ends: Start from the top and work down
(with the lower edge of the bar) to a third of the diameter of the trunk. Then saw from underneath with the upper edge of the bar until the two cuts meet. 4. Sawing on a sawhorse: Hold the electric chainsaw steady
A lot of experience is necessary
with both hands, keeping the saw in front of you while sawing. Once the saw is through the wood, guide the machine passed you on the right (1). Hold your left arm as straight as you can (2). Watch out for the falling trunk. Position yourself to prevent any danger from the separated trunk. Watch your feet. The trunk may cause injuries when falling. Keep your balance (3).
in felling trees. Cut down trees only when you can safely han- dle the electric chainsaw. In no case should you use the electric chainsaw if you feel unsure about anything.
Limbing is the designation for the sawing off of branches and boughs from a felled tree.
Many accidents occur during the
removal of branches. Never cut tree limbs when you are standing on the log. Keep the spring-back area in mind if branches are under tension.
Felling trees · Limbing

Do not fell any trees when a
strong or changing wind is blow- ing, if the danger of property dam- age exists or if the tree could fall on electric wires.
side of the log, where you stand to the left of the log and saw with the chainsaw pulling. The back cut must run horizontally not less than 5 cm above the horizontal notched cut. The back cut should be so deep
Immediately after termination of
the sawing procedure, remove the ear protection so that you can hear hooter and alarm signals.
that the separation distance between the back cut and the notch cutting line is at least 1/10 of the trunk diameter. The part of the log not sawed through is designated as a break dimen- sion. Insert a felling wedge or a crow-
positioning the cut from above the branch. With removal of branches, never work higher than shoulder level.
bar into the back cut, as soon as the depth of cut permits this, in order to prevent a jamming of the chain bar. 5. If the trunk diameter is larger
the tree to ensure an easy escape. The escape area (1) should be around 45° either side behind the planned felling direc- tion (2). 3. Cutting notch (A): Make a felling notch in the direc-
than the length of the chain bar, make two cuts.
For safety reasons, we advise inex-
perienced users not to fell any logs with a rail length which is smaller than the trunk diameter.
tion in which you wish the tree to fall. Start with an upper sawing cut. Now make a sawcut below,
which runs horizontally and en- counters the upper sawcut exactly. The depth of cut of the notch
As soon as the tree begins to
should be approx. 1/3 of the trunk diameter and the cutting angle at least 45°.
fall, pull out the saw from the section, stop the motor, place the electric chainsaw down and leave the workplace using the withdrawal path.
Never step in front of a tree which
is notched.

chain oil. • Clean the ventilation slots and the surfaces of the machine with a paint brush, whisk or dry cloth. Do not use any liquids for cleaning..
Basically, carry out mainte-
nance and cleaning works with switched-off motor and power plug removed. Danger of injury! Leave any maintenance and ser- vicing work not covered by this manual to our Service-Center. Use only original spare parts. Allow the machine to cool down before all maintenance and cleaning works. Danger of burn injuries!
Regularly carry out the maintenance opera- tions listed in the following table. The life of the saw is extended by regular maintenance of your chainsaw. Furthermore, you get optimum cutting performance and avoid ac- cidents.
Oiling the saw chain
Clean and oil the chain regularly. In
this way, you keep the chain sharp and get optimum machine perfor- mance. In case of damage due to inadequate maintenance of the saw chain, the guarantee claim is invalid. Remove the power plug and use cut-protection gloves when you are handling the chain or the chain bar.
Machine part Action Before every use
After 10 hours of operation
Components of the chain brake Check, replace if required
Sprocket chain wheel Check, replace if required
Saw chain Check oil, regrind or replace if required
Guide bar Check, turn round, clean and oil
Maintenance intervals · Cleaning · Maintenance Interval Table

cleaned thoroughly, in particular the teeth of the rail. Use a whisk and a dry cloth for that. • Oil the individual chain links with the aid of an oil suction gun with pinpoint tip (available in the specialist trade). Place individual oil drops onto the ar- ticulated links and onto the tooth tips of the individual chain links.

Deviations from the measure-
ment data of the cutting geom- etry can lead to an increase of the spring-back slope of the machine. Increased danger of ac- cident!
Sharpening the saw chain
An incorrectly sharpened saw
chain increases the danger of spring-back! Use cut-protection gloves when you are handling the chain or the chain bar.
Special tools are necessary for sharpen- ing the chain, which guarantee that the cutting edges are sharpened at the cor- rect angle and to the correct depth. For the inexperienced user of chainsaws, we recommend to have the saw chain sharpened by a specialist or a specialist workshop. If you think yourself capable of sharpening the chain, you can acquire the special tools in the specialist trade.
A sharp chain guarantees an optimal
cutting performance. It eats effort- lessly through the wood and leaves large, long wooden chips. A saw chain is blunt if you have to press the cutting equipment through the wood and the wooden chips are very small. In the case of a very blunt saw chain, no chip cuttings result at all, only sawdust.
Other diameters damage the
chain and can lead to danger during work!

Turn the saw around and sharpen the teeth of the other side. 6. The chain is worn and must be re- placed by a new saw chain if only approx. 4 mm of the cutting teeth is remaining. 7. After the sharpening, all cutting ele- ments must now be equal in length and width. 8. After every third sharpening, the sharpness depth (depth limitation) must be checked and the height filed with the aid of a flat file. The depth limita- tion should be set back about 0.65 mm from the cutting tooth. After the setting back of depth limitation, round it off a little at the front.
Never attach a new chain to a worn
drive pinion or place onto a dam- aged or worn chain bar. The chain could spring back or break, poten- tially leading to serious injury.
Maintaining the chain bar
Use cut-protection gloves when
handling the chain or the chain bar.
The blade must be inverted every 8-10 work- ing hours in order to guarantee even wear (see chapter “initial operation”).

Adjusting the chain tension
The adjustment of the chain tension is de- scribed in the chapter: Starting operation, tensioning chainsaw.
chain bar (24), in order to guar- antee a trouble-free, automatic oiling of the saw chain during operation. 5. Mount chain bar, chainsaw and sprocket chain wheel covering and tighten the chainsaw.
With the oil nozzles in good condi-
tion and the oil regulator set cor- rectly, the saw chain will spray a little oil off after starting.
Starting up a new saw chain
In the case of a new chain, the tensioning force decreases after some time. There- fore you must re-tension the chain after the first 5 cuts and at longer intervals after this.

Technical Data
Electrical chainsaw EKS 1835 QT Rated input voltage 230V~, 50 Hz Input power 1800 W Safety class II Protection type IP20 Chain speed 14,0 m/s Weight (without guide rail and chain) 3,94 kg Weight (with guide rail and chain)...4,63 kg Chain Oregon 91P53X Chain bar Oregon Typ 140SDEA041 Chain link separation 3/8“ (9,53 mm) Chain width 1,27 mm Teeth of the sprocket chain wheel 7 Sawing length max. 355 mm Length of the chain bar 410 mm Sound pressure level (LpA) 96,0 dB(A); KpA =3,0 dB(A) Sound power level (LPA) 107,3 dB(A); KwA =3,0 dB(A) guaranteed 112,0 dB(A) Vibration at the handle (an) 6,97 m/s2; K=1,5 m/s²
Do not dispose of used oil in the sewage system or drains. Dispose of used oil in an environmentally correct manner - bring it to a waste disposal center. Be environmentally friendly. Return the tool, accessories and packaging to a recycling centre when you have finished with them.
Machines do not belong with
domestic waste.
Empty the oil tank carefully and hand in your electric chainsaw at a disposal cent- er. The plastic and metal parts employed can be separated out and thus recycled use can be implemented. Ask our Service- Center for details. We dispose of your defective devices free of charge.
The following spares are available from Grizzly Service-Center Please indicate the machine type and the number of the spare part with your order.
The stated vibration emission value was measured in accordance with a standard testing procedure and may be used to compare one power tool to another. The stated vibration emission value may also be used for a preliminary exposure assessment.
Oregon saw chain 3009 1530 Oregon chain bar 3010 0353 Bio chain oil 1 liter 3023 0001 Bio chain oil 5 liter 3023 0002
If further spare parts should be necessary, please find the part number on the exploded drawings.
The Oregon replacement saw
chain is to be used only in con- junction with the associated Oregon blade and the electric chainsaw approved for this. There is a risk of injury.

of the operating cycle are to be considered, including, for example, times during which the power tool is turned off and times when the tool is turned on but is running idle).
flaws in the materials themselves. Also, all damage to the machine, the saw chain and the chain bar, which can be attributed to inadequate lubrication, are excluded from the guarantee. Furthermore, a condition of the guarantee services is that the maintenance intervals, indicated in the operating instruction, have been adhered to and the instructions on the cleaning, care and maintenance have been followed. Damages, which originate due to material or manufacturer faults, will be repaired free of charge by replacement delivery or repair. This is conditional upon the device being returned in one piece complete with proof of purchase and guar- antee to our service centre..
Technical and optical changes can be car- ried out in the course of further develop- ment without notice. All dimensions, refer- ences and information of this instruction manual are therefore without guarantee. Legal claims, which are made on the ba- sis of the instruction manual, cannot thus be considered as valid.
This device is designed for opera-
tion on a power supply network with a system impedance Zmax at the transfer point (domestic connection) of a maximum of 0.170 Ohms. The user must ensure that the device is operated only on a power supply network that fulfils this requirement. If necessary, the local power supply company can be asked for the sys- tem impedance.
Our Service-Center will also carry out any non-guarantee repair work for a charge. We will be happy to give you a quote. We will only work on units that have been sent in with the appropriate packaging, postage paid. The transportation risk is borne by the sender. Caution: Please, in no case, send defec- tive devices with filled oil tank. Completely empty the tank. Possible material dam- ages (oil runs out if device is placed on its side or upside down!) and/or fire damages during transport are borne at the expense of the sender. Devices sent in with freight collect - by bulk freight, express or with other spe- cial freight - are not accepted. We will dispose of tools free of charge..
This unit has a guarantee period of 36 months, or 12 months for units used on a commercial basis or for replacement units according to the statutory regulations. Damages, which can be attributed to natural wear, overloading or inappropriate use, are excluded from the guarantee. Certain component parts are subject to a normal wear and are excluded from the guarantee. In particular, these include: Saw chain, chain bar, sprocket chain wheel and carbon brushes, provided that the complaints cannot be attributed to

Problem Possible cause Fault correction
Check plug socket, cable, line and plug, where appropriate, repair by electrical specialist. Check house protection fuse, see note
House protection fuse activated
Device does not start
Defective On/Off switch Repair by customer service
Worn carbon brushes Repair by customer service
Defective motor Repair by customer service
Chain does not rotate Chain brake blocks saw chain
Check chain brake. Possibly release chain brake
Incorrectly mounted saw chain Mount saw chain correctly
Saw chain (5) blunt Sharpen cutting teeth or place on new chain
Chain tension insufficient Check chain tension
Saw runs with difficulty, chain comes off Chain tension insufficient Check chain tension
Check oil level and, where appropriate, refill with chain oil, check oil automatic system and, where appropriate, clean oil outflow duct or have repaired by customer service
Chain becomes hot, smoke development during sawing, discoloration of the rail
Too little chain oil
Mains voltage defective · Inferior cutting performance
Problèmes fréquents, causes probables et solutions.
| Problème | Cause possible | Solution | |
|---|---|---|---|
| Device does not start | Mains voltage defective House protection fuse activated | Check plug socket, cable, line and plug, where appropriate, repair by electrical specialist. Check house protection fuse, see note | p.18 |
| Device does not start | Defective On/Off switch | Repair by customer service | p.18 |
| Device does not start | Worn carbon brushes | Repair by customer service | p.18 |
| Device does not start | Defective motor | Repair by customer service | p.18 |
| Chain does not rotate | Chain brake blocks saw chain | Check chain brake. Possibly release chain brake | p.18 |
| Inferior cutting performance | Incorrectly mounted saw chain | Mount saw chain correctly | p.18 |
| Inferior cutting performance | Saw chain (5) blunt | Sharpen cutting teeth or place on new chain | p.18 |
| Inferior cutting performance | Chain tension insufficient | Check chain tension | p.18 |
| Saw runs with difficulty, chain comes off | Chain tension insufficient | Check chain tension | p.18 |
| Chain becomes hot, smoke development during sawing, discoloration of the rail | Too little chain oil | Check oil level and, where appropriate, refill with chain oil, check oil automatic system and, where appropriate, clean oil outflow duct or have repaired by customer service | p.18 |
Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.
Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.