FR
Ambrogio logo
Notice d'utilisation officielle

Ambrogio Basic

255 pages·6.1 MB·Tondeuse à gazon·PDF·ENJA
Ambrogio Basic
Table des matières 37 sections GENERAL INFORMATION · PURPOSE OF THE MANUAL · PROCEDURE TO REQUEST TECHNICAL ASSISTANCE · TECHNICAL INFORMATION · … AfficherMasquer
Page 1 of the Ambrogio Basic user manual
Page 1 · cliquer pour agrandir
Page 1
Page 1 of the Ambrogio Basic user manual
Page 2 of the Ambrogio Basic user manual — GENERAL INFORMATION
Page 2 · cliquer pour agrandir
Page 2

GENERAL INFORMATION

PURPOSE OF THE MANUAL

This manual, which is an integral part of the equipment, was made by the manu- facturer to provide authorized personnel the information necessary to interact with it for the duration of its estimated lifespan.

The manufacturer reserves the right to make changes without any prior notice.

The relevance of certain parts of the manual and of some specifications is pointed out by a few symbols whose meaning is described below.

Besides adopting a good operation tech- nique, the recipients of the information should carefully read it and apply it rigorous- ly.

This information is provided by the man- ufacturer in his own native language (Ital- ian) and it can be translated into other languages to meet both legislative and/ or commercial needs.

Spend some of your time reading this in- formation to avoid any risk for people’s health and safety as well as economic damage.

Keep this manual for the entire working life of the equipment in a suitable and easily accessible place, so that it will al- ways be available when consultation be- comes necessary.

Ambrogio Basic — GENERAL INFORMATION diagram (page 2)
Fig. 1

The dataplate shown here is fitted directly to the appliance. It fea- tures references and all essential information for operating safety. A) Manufacturer identification B) EC compliance marking C) Serial model/number year of

Page 3 of the Ambrogio Basic user manual — TECHNICAL INFORMATION
Page 3 · cliquer pour agrandir
Page 3

PROCEDURE TO REQUEST TECHNICAL ASSISTANCE

For every technical service request re- garding the machine, please indicate the data found on the identification plate, the

approximate hours of use and the type of fault detected.

TECHNICAL INFORMATION

GENERAL DESCRIPTION OF THE EQUIPMENT

The appliance Ambrogio Line 100 is a robot designed and built to automatically trim grass in gardens and house lawns in any time of the day. It is small, com- pact, silent, waterproof and easy to transport.

Ambrogio Basic — TECHNICAL INFORMATION diagram (page 3)
Fig. 2

During its functioning the robot trims the area marked off by the perimeter wire and/or by barri- ers (fences, walls, etc.)

When the robot detects the perim- eter wire or meets an obstacle, it re- verses its advancement direction and randomly changes its path.

According to its functioning prin- ciple ("random"), the robot car- ries out an automatic and complete trimming of the marked off lawn (see figure)

The lawn surface that the robot is able to trim depends on a series of factors. – robot model and type of batteries in-

The robot trims and stops near the perime- ter wire, once the battery charge runs out.

stalled – area features (irregular perimeters,

DELUXE version: model accessorized with remote control and sensor to de- tect "trimmed lawn".

uneven surface, divided area, etc.) – lawn features (type and height of

grass, moisture, etc.) – blade conditions (with efficient sharp-

The robot trims and stops near the perime- ter wire, when the sensor detects that the lawn has been completely trimmed.

ening, without residues and deposits, etc)

Both models are equipped with a sensor, which stops them automatically in case of rain.

The robot Ambrogio Line 100 is pro- duced in the BASIC and DELUXE ver- sions.

Upon request, the models can be equipped with an upgraded transmitter, electromagnetic interference filter and power supply safety box.

BASIC version: basic model, which can be supplied with remote control upon re- quest.

robot · robot

Page 4 of the Ambrogio Basic user manual — PROCEDURE TO REQUEST TECHNICAL ASSISTANCE
Page 4 · cliquer pour agrandir
Page 4

Main components – Accumulator batteries (A): they en-

– Electric motor (G)it starts the cut-

ting blade (F). – Electric motor (H): one starts the

ergize the motors of the blade and of the wheel control system. The robot is supplied with lead batter- ies or with one or two lithium batter- ies, which assure a longer working session. – Battery recharge connection (B): it

right wheels drive unit, while the other one starts the one of the left wheels. – Transmitter (L): it transmits the sig-

nal to the perimeter wire. – Power supply unit (M): it energizes,

at low tension, the battery power.

is used to connect the batteries (A) during recharge. – Electronic card (C): it checks the au-

tomatic functions of the robot. – Drive unit (D): it drives the right and

left wheels with two independent mo- tors. – Control keyboard (E): it is used to set

– Shock sensor (N)it detects the im-

pact of the robot against an obstacle, reversing its advancement direction. – Remote control (P): it is used to

and visualise the functioning modes of the robot. – Cutting blade (F): it trims the lawn.

check the robot functions in a remote position.

Ambrogio Basic — PROCEDURE TO REQUEST TECHNICAL ASSISTANCE diagram (page 4)
Fig. 3
Page 5 of the Ambrogio Basic user manual — SPECIFICATIONS
Page 5 · cliquer pour agrandir
Page 5

SPECIFICATIONS

Description Model BASIC DELUX Cutting blade 4 (mm) ø290 ø290 Cutting speed (m/min) 25 25 Cutting height (mm) 20÷100 20÷100 Maximum gradient of the surface to trim 30° (57%) 30° (57%) Electric motors (V) cc 24V cc 24V Size (basexheightxdepth) (mm) 510x330x433 510x330x433 Robot weight (without batteries) (kg) 10,5 10,5 Ambient functioning temperature max 40 °C 40 °C Battery accumulator recharge type Battery accumulators (lead) (V/A) 27,6V - 4,0A 27,6V - 4,0A Battery accumulators (lithium) (V/A) 29,5V - 4,0A 29,5V - 4,0A Maximum surface that can be trimmed Robot with two lead batteries (12V-7A) m2 400 400 Robot with two lead batteries (12V-12A) m2 700 700 Robot with one lithium battery (25.2V-6A) m2 700 700 Robot with two lithium batteries (25.2V-6A) m2 1000 1000 Electric specifications

Class 1 (Vin 115-230 Vac 50Hz) Fuse

5x20 4A F (inside) 27,6 Vac Fuse 5x20 10A F (replaceable) Selector 115-230 Vac

Power supply unit (for lead battery)

Class 1 (Vin 115-230 Vac 50Hz) Fuse

Power supply unit (for lithium battery)

5x20 4A F (inside) 29,5 Vac Fuse 5x20 10A F (replaceable) Selector 115-230 Vac Section perimeter wire (to lay underground) (mm) ø1,5 ø1,5 Perimeter wire maximum length (approximate, calculated according to a regular perimeter)

Sinusoidal perimeter signal (patented) Standard equipment

Trimmed lawn sensor not available Standard equipment

Rain sensor Standard equipment

Standard equipment Remote control upon request upon request Upgraded transmitter upon request upon request Electromagnetic interference filter upon request upon request Power supply safety box upon request upon request Kit for working with gradients higher than 30° (1) upon request upon request

Perimeter wire (m 100) Standard equipment

Fixing nails (n. 100) Standard equipment

(1) If the ground conditions are suitable (solid, without excessive folds, etc.), the kit allows the robot to work (within certain

limits) beyond the maximum admissible gradients.

Show 5 more labels / short text on this page
(m) 600 600 · Fittings · Standard equipment · Standard equipment · Standard equipment
Page 6 of the Ambrogio Basic user manual — SAFETY INFORMATION
Page 6 · cliquer pour agrandir
Page 6

SAFETY INFORMATION

SAFETY RULES

– During design and construction, the

Improper use can create health and safety risks for personnel and cause costly damage. – Before using the lawn mower make

manufacturer has carefully consid- ered the possible hazards and per- sonal risks that may result from interaction with the machine. In addi- tion to observing the specific laws in force, the manufacturer has adopted all "exemplary construction technique principles". The purpose of this infor- mation is to advise the users to use extreme caution to avoid risks. How- ever, discretion is invaluable. Safety is also in the hands of all the operators who interact with the machine. – When using the robot for the first

sure that no objects are on the lawn (toys, tree branches, items of cloth- ing, etc.). – When using the machine, make sure

there are no risks especially for chil- dren, pets and things. – Do not place hands or feet under the

machine when running especially in the wheel area. – Do not tamper with, elude, remove or

by-pass the installed safety devices. Any failure to comply with this require- ment may cause serious risks for peo- ple’s safety and health. – Keep the lawn mower in perfect oper-

time, it is recommended to carefully read the whole manual and to be sure to have it completely under- stood, in particular all the informa- tion relating to safety. – Read carefully the instructions con-

ating conditions by performing the maintenance procedures outlined by the manufacturer. Good maintenance guarantees better performance and longer service life. – Before maintenance and setting pro-

tained in the manual supplied and those applied on the equipment, in particular follow those concerning safety. Spend some of your time read- ing the instructions to avoid unpleas- ant accidents; it is useless to remember what had to be done when an accident has already occurred. – Perform lifting and handling observing

cedures are performed – also by the user, if possessing the necessary technical skills – disconnect the pow- er supply. The user must in any case operate in full safety conditions, espe- cially when working on the lower part of the lawn mower, following the pro- cedures as illustrated by the manu- facturer. – Use personal protections as recom-

the information found directly on the packaging, on the machine and in the instructions furnished by the manu- facturer. – Pay attention to the meaning of the

symbols in the applied plates; their shape and colour have a specific meaning related to safety. Keep them visible and follow the stated informa- tion. – The lawn mower may be used only by

mended by the manufacturer, espe- cially the protective gloves when handling blades and cutting discs. – Always remove the blade before re-

placing the batteries. – In order not to irreversibly damage

those who know how to operate it af- ter reading and understanding the in- structions in this manual. – Use the equipment only for the uses

electric and electronic parts, do not wash the robot with water jets at a high pressure and do not plunge it partially or thoroughly in water, as it is not watertight.

provided for by the manufacturer.

Page 7 of the Ambrogio Basic user manual — SAFETY SIGNALS
Page 7 · cliquer pour agrandir
Page 7

– The operators performing repair in-

– All operations, which must be carried

terventions during the working life of the robot must have technical exper- tise, special abilities and experience, acquired and acknowledged in this specific sector. The lack of these re- quirements may cause damage to the safety and health of people.

out in the recharge base (optional), must be performed with the power supply plug disconnected. – Replace deteriorated parts with origi-

nals to ensure functionality and the foreseen safety level.

SAFETY FOR MAN AND THE ENVIRONMENT DURING DISPOSAL

Do not throw away any polluting mate- rial in the environment. Carry out their disposal in compliance with the rele- vant legislation in force.

(WEEE) is subject to fine according to sanctions regulated by the laws in force in the territory where the infraction has been verified.

With reference to the WEEE directive (Waste of Electrical and Electronic Equipment), during dismantling, the user must separate the electrical and the electronic components and dispose them in the appropriate authorized col- lection centres or give them back as they are to the seller, when a new purchase is made.

As implementation of the European di- rectives (2002/95/CE, 2002/96/ CE, 2003/108/CE) in the Italian terri- tory, for example, a law decree (n. 151 dated July 25 2005) has been enact- ed, thus providing for an administrative fine of € 2000÷5000.

All the components, which must be sep- arated and disposed of in a specific man- ner, are marked with a special mark.

The unauthorized disposal of Waste of Electrical and Electronic Equipment

SAFETY SIGNALS

Page 8 of the Ambrogio Basic user manual — EQUIPMENT INSTALLATION PLANNING
Page 8 · cliquer pour agrandir
Page 8

INSTALLATION

PACKAGING AND UNPACKING

The machine is delivered suitably pack- aged. When unpacking, remove carefully and check component integrity. All the necessary information for han- dling is found on the packaging.

– remote control (L) (DELUXE version) – Lithium or lead batteries (M) (the

quantity of the lithium batteries varies according to the purchase order) – Blade (N)

Packaging content – robot (A); – Power supply unit (B) – power supply cable (C) – cable for accumulator battery re-

charge (D) – transmitter (E) – perimeter wire hank (F) – nails (G) for wire fixing – user manual (H)

Keep the packaging for future usage.

Ambrogio Basic — INSTALLATION diagram (page 8)
Fig. 4

EQUIPMENT INSTALLATION PLANNING

The installation of the robot does not re- quire difficult performance interventions, but requires a minimum preliminary

planning, so to establish the best area to install power supply-transmitter unit and to trace the path of the perimeter wire.

Page 9 of the Ambrogio Basic user manual — INSTALLATION
Page 9 · cliquer pour agrandir
Page 9

Power supply-transmitter unit in- stallation area – The unit must be far from the

Ambrogio Basic — INSTALLATION diagram (page 9)
Fig. 5

perimeter wire from at least 2 m to maximum 10 m. – The unit must be in a ventilated

position, safe from atmospher- ic agents and from direct sun- light. – The unit must not be in direct

contact with the ground or with humid environments.

Perimeter wire path definition – Check the conditions of the area to

trim to define the perimeter and carry out in sequence all the operations. – Arrangement and marking of the

working area (see page 12) – Perimeter wire installation (see page

15. – Power supply-transmitter unit installa-

tion (see page 17)

power supply-transmitter unit · perimeter wire · wire laying direction

Page 10 of the Ambrogio Basic user manual — ARRANGEMENT AND MARKING OF THE WORKING AREA
Page 10 · cliquer pour agrandir
Page 10

ARRANGEMENT AND MARKING OF THE WORKING AREA

Arrangement of lawn to trim

1-Check that the lawn to trim is even, and without pits, stones or other obstacles. If so, per- form the necessary clearance operations. If some obstacles cannot be removed, it is necessary to properly mark the areas in- volved. 2-Check that all the areas of the lawn do not exceed the admis- sible gradients (see "Specifica- tions")

Ambrogio Basic — ARRANGEMENT AND MARKING OF THE WORKING AREA diagram (page 10)
Fig. 6

If the proper kit is installed and the conditions of the ground are suitable (solid, without excessive folds, etc.), the robot can work (within certain limits) be- yond the maximum admissible gradi- ents.

Marking of working area Before starting installation opera- tions of the perimeter wire, to make them easy to perform, it is recom- mended to properly signal the whole path evenly with straight lines and to trace any curved line.

Ambrogio Basic — ARRANGEMENT AND MARKING OF THE WORKING AREA diagram (page 10)
Fig. 7

The figure represents an example of lawn with the trace for the un- derground laying of the perimeter wire.

track for perimeter wire laying

Page 11 of the Ambrogio Basic user manual — ARRANGEMENT AND MARKING OF THE WORKING AREA
Page 11 · cliquer pour agrandir
Page 11

1-Check the whole surface of the lawn and assess whether it is necessary to divide it in more separated working areas.

Ambrogio Basic — ARRANGEMENT AND MARKING OF THE WORKING AREA diagram (page 11)
Fig. 8
Show 5 more labels / short text on this page
wall · passage aisle · house · passage aisle (<2m) · house
Page 12 of the Ambrogio Basic user manual — ARRANGEMENT AND MARKING OF THE WORKING AREA
Page 12 · cliquer pour agrandir
Page 12

2-Mark and trace the perime- ters of the inside and marginal elements of the working area that obstruct the correct func- tioning of the robot.

Ambrogio Basic — ARRANGEMENT AND MARKING OF THE WORKING AREA diagram (page 12)
Fig. 9

Mark and trace the perimeters of all the elements in iron or in other metals (manholes, electric connections, etc.) to avoid inter- ferences to the signal of the pe- rimeter wire.

Do not mark those obstacles (trees, poles, etc.) that do not hamper the normal functioning of the robot.

Ambrogio Basic — ARRANGEMENT AND MARKING OF THE WORKING AREA diagram (page 12)
Fig. 10
Show 8 more labels / short text on this page
manhole · bed · protruding roots · hedge · wall · shower dish · pool · tree pole
Page 13 of the Ambrogio Basic user manual — ARRANGEMENT AND MARKING OF THE WORKING AREA
Page 13 · cliquer pour agrandir
Page 13

3-Mark the areas, located in a lower position compared to the lawn surface (pools, areas with significant drops, stairs, etc.) (see example in figure)

Ambrogio Basic — ARRANGEMENT AND MARKING OF THE WORKING AREA diagram (page 13)
Fig. 11

4-Mark and trace the perime- ters as shown in the figure. – With small paths at the same

Ambrogio Basic — ARRANGEMENT AND MARKING OF THE WORKING AREA diagram (page 13)
Fig. 12
height as the lawn5 cm – With small paths higher than
the lawn35 cm – In presence of a fencing wall:

35 cm – The passage paths (at the

same level of the lawn), neces- sary for the robot to pass from one area to the other, must not be marked.

Ambrogio Basic — ARRANGEMENT AND MARKING OF THE WORKING AREA diagram (page 13)
Fig. 13

The perimeter wire may be laid un- derground or on the ground.

Show 7 more labels / short text on this page
elevated area · pool · perimeter wire · pedestrian crossing · perimeter wire · wall pedestrian crossing · perimeter wire
Page 14 of the Ambrogio Basic user manual — ARRANGEMENT AND MARKING OF THE WORKING AREA
Page 14 · cliquer pour agrandir
Page 14

Wire laid on the ground

Ambrogio Basic — ARRANGEMENT AND MARKING OF THE WORKING AREA diagram (page 14)
Fig. 14

1-Place the wire clockwise along the whole path and fix it with the appropriate nails supplied (distance between the nails 1÷2 m). In the straight stretches, fix the wire so that it is not excessively tight, wavy and/or twisted. In the not straight stretches, fix the wire so that it does not twist, but so that it takes on a regular bending.

1-Dig up the ground evenly and sym- metrically compared to the traced line highlighted on the ground. 2-Place the wire clockwise along the whole path at the depth of some cen- timetres (about 2÷3 cm) so not to reduce the quality and the intensity of the signal captured by the robot.

3-When laying the wire, if necessary, block it in some points with the appro- priate nails to keep it in position dur- ing the ground covering stage. 4-Cover up the whole wire with the soil and make sure that it does not twist, but that it remains straight and that, in the curving stretches, it takes on an even bending.

Ambrogio Basic — ARRANGEMENT AND MARKING OF THE WORKING AREA diagram (page 14)
Fig. 15
Show 6 more labels / short text on this page
fixing nails · perimeter wire · fixing nails · perimeter wire · Underground laid wire · passage aisle (<2m)
Page 15 of the Ambrogio Basic user manual — POWER SUPPLY-TRANSMITTER UNIT INSTALLATION
Page 15 · cliquer pour agrandir
Page 15
Ambrogio Basic — POWER SUPPLY-TRANSMITTER UNIT INSTALLATION diagram (page 15)
Fig. 16

During the joint stage, it is rec- ommended to use self-amalga- mating tape (for example: 3M Scotch 23). Do not use isolating tape or other types of joints (ter- minals, clamps, etc.).

POWER SUPPLY-TRANSMITTER UNIT INSTALLATION

1-Installation of the power sup- ply-transmitter unit (A-B).

power supply unit (A)

2-Operate on the cursor (C) to select the power supply voltage (110 V or 220 V). 3-Press the button (F) of the power supply unit on OFF. 4-Connect the plug of the power supply unit (A) to the power socket. 5-Twist the final part of the pe- rimeter wire (about 1÷2 m) and connect the two ends to the terminal board (E). 6-Press the button (F) of the power supply unit on ON. 7-If the led (G) turns on and the led (D) flashes alternately green and orange, the connection is correct. Otherwise, it is necessary to find the defect (see "Troubleshooting")

Show 6 more labels / short text on this page
push button (F) · led (D) · cursor (C) · terminal board (E) · led (G) · transmitter (B)
Page 16 of the Ambrogio Basic user manual — POWER SUPPLY-TRANSMITTER UNIT INSTALLATION
Page 16 · cliquer pour agrandir
Page 16
Ambrogio Basic — POWER SUPPLY-TRANSMITTER UNIT INSTALLATION diagram (page 16)
Fig. 17

The robot can be energized with two lead batteries or with one or two lithium batteries. Install the batteries as shown.

1-Undo the knobs (A). 2-Remove the hood (B).

3-Unscrew the screws (D) and remove the guard (E).

4-Loosen the screws (F). 5-Remove the brackets (G) and the spacers.

Page 17 of the Ambrogio Basic user manual — LITHIUM BATTERY
Page 17 · cliquer pour agrandir
Page 17
Ambrogio Basic — LEAD BATTERY diagram (page 17)
Fig. 18

LEAD BATTERY

1-Insert the batteries (H) in the appropriate positions. 2-Take out one of the connectors (M). 3-Connect the (blue) cable (L) to the connectors. 4-Connect the (red) cable (N) to the connector. 5-Connect the (black) cable (P) to the connector.

cable (P) cable (N)

Ambrogio Basic — LEAD BATTERY diagram (page 17)
Fig. 19

LITHIUM BATTERY

1-Insert the battery (Q) in the ap- propriate position. 2-Check that both connectors (M) are inserted. 3-Connect the (red) cable (R) to the connector. 4-Connect the (black) cable (S) to the connector.

Ambrogio Basic — LITHIUM BATTERY diagram (page 17)
Fig. 20

1-Assemble brackets (G) and fix them with screws (F).

screw (F) bracket (G)

Show 16 more labels / short text on this page
Lead battery connection · cable (L) · battery (H) · battery (H) · connector (M) · cable (L) · Lithium battery connection · cable (S) · battery (Q) · connector (M) · battery (Q) · cable (R) · cable (R) · cable (S) · Battery fixing · bracket (G)
Page 18 of the Ambrogio Basic user manual — LEAD BATTERY
Page 18 · cliquer pour agrandir
Page 18
Ambrogio Basic — LEAD BATTERY diagram (page 18)
Fig. 21

2-Reassemble body cover (E) and tighten screws (D).

4-Fasten knobs (A). 5-Install the blade (see "Blade in- stallation").

At this point, the robot is ready to use (see "Use and functioning").

Page 19 of the Ambrogio Basic user manual — LEAD BATTERY
Page 19 · cliquer pour agrandir
Page 19
Ambrogio Basic — LEAD BATTERY diagram (page 19)
Fig. 22

1-Before assembling and/or re- placing the blade, make sure that the robot has been stopped in safety conditions (see "Robot safety stop") 2-Turn the robot upside down and put it down so not to ruin the covering hood. 3-Assemble the blade (U).

4-Tighten screws (V). 5-Capsize the robot in its func- tioning position. Before turning the robot on, check that the batteries are charged (see "Battery recharge").

Ambrogio Basic — LEAD BATTERY diagram (page 19)
Fig. 23

Any extraordinary adjustments, not ex- plicitly indicated in the manual, must be carried out only by the staff of the Au- thorized Assistance Centres of the Manufacturer.

Ambrogio Basic — LEAD BATTERY diagram (page 19)
Fig. 24

1-Stop the robot in safety condi- tions (see "Robot safety stop") 2-Undo the knobs (A). 3-Remove the hood (B).

Page 20 of the Ambrogio Basic user manual — LEAD BATTERY
Page 20 · cliquer pour agrandir
Page 20
Ambrogio Basic — LEAD BATTERY diagram (page 20)
Fig. 25

4-Undo the screws (C) and re- move the body cover (D) on both sides.

5-Loosen the screws (E) (3 com- plete turns). 6-Operate on the support (F) to adjust the tension of the chain (G). 7-Tighten screws (E).

8-Equally tension also the other chain 9-Reassemble body cover (D) and tighten screws (C).

10-Assemble the top hood (B) and screw in the charge knobs (A).

Page 21 of the Ambrogio Basic user manual — LEAD BATTERY
Page 21 · cliquer pour agrandir
Page 21
Ambrogio Basic — LEAD BATTERY diagram (page 21)
Fig. 26
Ambrogio Basic — LEAD BATTERY diagram (page 21)
Fig. 27

Use the equipment only for the tasks authorised by the manufacturer and do not tamper with any device to achieve a different performance from the oper- ating one.

Ambrogio Basic — LEAD BATTERY diagram (page 21)
Fig. 28

The illustration represents the posi- tion of the controls on the machine. –"Start" (A) push button: it is

used to start the robot in differ- ent operation modes.

"start" push button, if pressed shortly, is used to turn it on with the "perimeter wire identi- fication". –With the robot already turned

on, the "start" push button, if pressed shortly, is used to start it with the blade in motion.

Page 22 of the Ambrogio Basic user manual — LEAD BATTERY
Page 22 · cliquer pour agrandir
Page 22

–With the robot that has

Ambrogio Basic — LEAD BATTERY diagram (page 22)
Fig. 29

stopped automatically in the stand-by mode, the "start" push button is used to detect, ac- cording to the led type on, the reason of the stop and/or the causes, for which the robot does not restart. –With the robot turned off, the

"start" push button, if pressed for an extended time, (more than seconds), is used to turn it on without the "perimeter wire identification". –With the robot in motion, the

"start" push button, if pressed for an extended time, (more than seconds), is used to stop or start the cutting blade. –"Stop" (B) push button: it is

used to stop the robot and the rotation of the blade.

–Led (E) (green) on and led (H) (yel-

low) off: they indicate that the robot is functioning in the "without perimeter wire identification" mode. –Led (E) (green) on and led (H) (yellow)

LED description –Led (C) (green): it indicates the charge

status of the batteries of the accumu- lators. –Led on: it indicates that the batteries

flashing: they indicate that the robot does not receive the signal from the pe- rimeter wire. The robot will automatical- ly restart the trimming cycle as soon as the hitch is resolved. –Led (E) (green) flashing and led (G)

are charged. – Led flashingit indicates that the bat-

teries are not completely charged. –Led (D) (red): it indicates that the bat-

teries charge is running down (the led (C) has turned off). –Led flashing: it indicates that the bat-

(blue) on: they indicate that the robot has completed the trimming of the lawn. The robot will automatically re- start the trimming cycle on the follow- ing day. –Led (E) (green) and led (G) (blue)

teries are about to run down. –Led on: it indicates that the batteries

have completely run down. –Led (E-G-H): if they are on in the various

flashing: they indicate that the robot has stopped trimming the lawn due to rain. The robot will automatically re- start the trimming cycle on the follow- ing day. –Led (F) (red) on or flashing in combina-

combinations, they indicate the opera- tion conditions of the robot. – Led (E) (green) flashing and led (G)

(blue) off: they indicate that the robot is activated but not functioning. To make the robot function, press the "start" (A) push button. – Led (E) (green) and led (H) (yellow)

tion with the turning on of the leds (E-G- H) indicates that the robot is in break- down. To identify the type of breakdown and the solution to adopt, see "Trouble- shooting".

on: they indicate that the robot is func- tioning in the "perimeter wire identifi- cation" mode.

Page 23 of the Ambrogio Basic user manual — LEAD BATTERY
Page 23 · cliquer pour agrandir
Page 23
Ambrogio Basic — LEAD BATTERY diagram (page 23)
Fig. 30

–"Start" (L) push button: it is

used to turn on the robot from a remote position (movement, U turn, blade stop and restart and transfer from one area to anoth- er). The "Start" (L) push button, if pressed shortly with the robot al- ready on, is used to start it (with the blade in motion) or to stop it.

– Push buttons (M-N)they are used to

make the robot bend towards right or left. The robot keeps on bending towards a di- rection or the other until the relating push button (right or left) is kept pressed. When the push button is released, the robot proceeds along a straight path. –Push button (P): available to activate

The "start" push button, if pressed short- ly two times in a row, is used to change the direction of the robot. The "start" push button, if pressed for an extended time, is used to stop the robot and make it restart with the blade disen- abled. If pressed again for an extended time, it is used to restart the blade. With the robot that has stopped auto- matically and that, after 30 seconds, has entered in the stand-by mode, the "start" push button, if pressed for a short time, is used to restart the robot.

future functions.

If the remote control does not work, because it does not recognize the code associated to the referring robot, it is necessary to carry out its program- ming (see "Remote control program- ming procedure").

Page 24 of the Ambrogio Basic user manual — (A)
Page 24 · cliquer pour agrandir
Page 24

MANUAL START AND STOP OF THE ROBOT

Place the robot inside the working area at least 1 m far from the pe- rimeter wire and from any other obstacle.

Ambrogio Basic — MANUAL START AND STOP OF THE ROBOT diagram (page 24)
Fig. 31

1-Press shortly the "start" (A) push button. The (green) led (E) flashes to indi- cate that the robot is on and it is in the "pause" mode. The start of the robot can be car- ried out with two different modes (immediate or delayed start).

Ambrogio Basic — MANUAL START AND STOP OF THE ROBOT diagram (page 24)
Fig. 32

led (E) led (F)

(A)

(B)

1-Press again shortly the "start" (A) push button or (L). The leds (E) (green) and (H) (yellow) turn on. The robot starts with the stopped blade, which will start functioning after the robot has proceeded for at least 1 m without meeting obstacles and/or the perimeter wire.

led (G) led (H)

The robot and the blade stop almost in- stantly.

2-Press again for an extended time the "start" (A) push button. The leds (E) (green), (H) (yellow) turn on and the led (B) (blue) flashes. After 30 seconds, the robot enters in the stand-by mode and will start trim- ming the lawn after 3 hours.

The stop condition is indicated by the flashing turning on of the led (E) (green).

Show 11 more labels / short text on this page
led (C) · push button · batteries · push button · led (D) · Immediate start · push button (L) · push button (M) · push button (P) · push button (N) · Delayed start
Page 25 of the Ambrogio Basic user manual — ROBOT SAFETY STOP
Page 25 · cliquer pour agrandir
Page 25

To restart the robot, proceed as shown.

turn on. The robot, with the blade on, starts trimming the lawn inside the area marked by the perimeter wire.

3-Press again shortly the "start" (A) push button or (L). The led (E) (green) and (H) (yellow)

ROBOT START WITHOUT PERIMETER WIRE

This mode can be carried out with the re- mote control to perform the trimming of areas completely marked by fences or to trim, for example, small areas, where it was not possible to mark or for practical demonstrations on the functioning of the robot

2-Press shortly the "start" (A) push but- ton or (L). The led (E) (green) turns on, while the led (H) (yellow) remains off. The ro- bot, with the blade on, starts trim- ming the lawn of the area.

1-Press for an extended time (about 3 seconds) the "start" (A) push button and release it when the leds (E-F-G-H) start flashing. The "without perimeter wire" mode is indicated by the led (E) (green) flash- ing and by the led (H) (yellow) off.

ROBOT SAFETY STOP

When using the robot, it may necessary to stop it in safety conditions to avoid the ranger to a sudden start of the blade.

To stop the robot, press the "stop" (B) push button.

Page 26 of the Ambrogio Basic user manual — ROBOT START WITHOUT PERIMETER WIRE
Page 26 · cliquer pour agrandir
Page 26
Ambrogio Basic — ROBOT START WITHOUT PERIMETER WIRE diagram (page 26)
Fig. 33

The robot stops automatically when the listed conditions occur. 1) Run-down batteries: The con- dition is indicated by the turn- ing on of the led (D) (red) relating to the batteries. 2) Rain: the condition is indicated by the flashing turning on of the led (E) (green) and led (G) (blue). When the robot stops in "rain" conditions, it can be restarted with a voluntary action. To restart the robot, press shortly the "start" (A) push but- ton or (L). The robot restarts trimming the lawn. To disable the "rain" detection sensor, stop the robot with the "stop" (B) key. To restart the robot during rain, see "Manual start and stop of the robot". In such conditions, the "rain" detection sensor automati- cally deactivates. Once it stops raining, it is possible to reactivate the "rain" detection sensor by means of the "stop" (B) push button and by repeating the start procedures (see "Manual start and stop of the ro- bot") 3) Trimmed lawn: the sensor (optional in the BASIC version) detects the trimmed lawn. The condition is indicated by the flash- ing turning on of the led (E) (green) and by the turning on of the led (G) (blue). When the conditions of "run-down bat- teries", "rain" or "trimmed lawn" occur, the robot reaches the nearest perime- ter wire and stops in the "stand-by" mode to reduce the consumption of batteries. The "stand-by" mode is indicated by the turning off of the leds (E-F-G-H) and eve- ry 5 seconds by the turning on of the leds of the batteries that indicate the stand-by condition and their charge lev- el.

According to the point, where the robot stops, it is possible to recognize the rea- son of the stop. Robot stop above the perimeter wire: it indicates that the battery has run down. Robot stop inside the perimeter (at about 1 m from the perimeter wire): it in- dicates that the lawn is trimmed or there is rain.

If the stop was not due to run-down batteries, the robot will restart auto- matically 24 hours later from the first start.

Page 27 of the Ambrogio Basic user manual — REMOTE CONTROL PROGRAMMING PROCEDURE
Page 27 · cliquer pour agrandir
Page 27

ROBOT MANUAL TRANSFER (FROM ONE AREA TO ANOTHER)

Before lifting the robot to manually trans- fer it in another working area, it is neces- sary to stop it in safety conditions.

The robot and the blade stop almost in- stantly.

Take the robot in the other working area and start it (see "Manual start and stop of the robot").

To stop the robot, it is enough to press the "stop" (B) push button.

ROBOT TRANSFER BY REMOTE CONTROL (FROM ONE AREA TO ANOTHER)

This functioning mode is used to make the robot move with the stopped blade (for example to cross connection areas from one area to another (not to trim) at least 70 cm wide).

After the robot has been guided with the remote control in new area to trim, press again the "start" (L) push button for an extended time (over 3 seconds).

The robot stops and restarts after a short while with the blade in motion to trim the lawn of the new marked area.

Press the "start" (L) push button for an extended time (over 3 seconds).

The robot stops and restarts after a short while with the stopped blade.

REMOTE CONTROL PROGRAMMING PROCEDURE

4-Press in sequence the (M) push but- ton, then the (L) push button and, fi- nally, the (N) push button.

1-Press the "start" (A) push button of the robot and keep it pushed. 2-Press the "start" (L) push button of the remote control and release it when the robot releases an acoustic signal and the leds (G-H) flash alter- nately. 3-Release the "start" (A) push button.

Once programming is completed, re- start the robot and try to use it with the remote control to check its correct func- tioning (see "Robot start without perime- ter wire").

Page 28 of the Ambrogio Basic user manual — BATTERY RECHARGE
Page 28 · cliquer pour agrandir
Page 28

BATTERY RECHARGE

1-Turn off the robot and place it near the transmitter. The led (E) (red) on indicates that the batteries have com- pletely run down.

Ambrogio Basic — BATTERY RECHARGE diagram (page 28)
Fig. 34

2-Connect the connector (G) (red, polarity +). 3-Connect the connector (H) (black, polarity -).

power supply unit (F)

Until the led (E) (red) of the power supply unit (F) remains on, the bat- tery is not completely charged. The completion of the recharge is indicated by the turning on of the led (E) (green).

To obtain a complete recharge of the batteries, it is advised to keep them connected to the recharge unit for about 3÷4 hours (to as- sess also according to the general condi- tions of the batteries).

4-Disconnect the connector (G) (red, polarity +). 5-Disconnect the connector (H) (black, polarity -).

Show 5 more labels / short text on this page
connector (H) · connector (G) · led (D) · led (E) · transmitter (B)
Page 29 of the Ambrogio Basic user manual — BATTERY RECHARGE
Page 29 · cliquer pour agrandir
Page 29
Ambrogio Basic — BATTERY RECHARGE diagram (page 29)
Fig. 35

Before setting the cutting height of the blade, make sure that the robot has stopped in safety condi- tions (see "Robot safety stop")

1-Place the robot on a flat base surface. 2-Undo the knobs (A). 3-Remove the hood (B).

4-Undo the screws (C) and re- move the body cover (D) on both sides.

5-Detect from the measuring scale (H) the height value of the set trimming. 6-Insert a shim under the chas- sis (F) of the robot (see figure) so to increase or decrease the cutting height value compared to the one detected on the measuring scale (H).

Page 30 of the Ambrogio Basic user manual — BATTERY RECHARGE
Page 30 · cliquer pour agrandir
Page 30

7-Loosen the screws (E) (4 com- plete turns).

Ambrogio Basic — BATTERY RECHARGE diagram (page 30)
Fig. 36

8-Lower the wheels to lay them on the base surface or lift them to keep the robot on the shim inserted. 9-Tighten screws (E).

Ambrogio Basic — BATTERY RECHARGE diagram (page 30)
Fig. 37

By means of the measuring scale it is possible to detect the new set cutting height. 10-If the value of the height de- tected on the measuring scale is correct, repeat the opera- tion on the other side.

Ambrogio Basic — BATTERY RECHARGE diagram (page 30)
Fig. 38

11-Reassemble the body cover (D) and tighten the screws (C) on both sides.

Page 31 of the Ambrogio Basic user manual — BATTERY RECHARGE
Page 31 · cliquer pour agrandir
Page 31
Ambrogio Basic — BATTERY RECHARGE diagram (page 31)
Fig. 39
Ambrogio Basic — BATTERY RECHARGE diagram (page 31)
Fig. 40
Page 32 of the Ambrogio Basic user manual — ORDINARY MAINTENANCE
Page 32 · cliquer pour agrandir
Page 32

PROLONGED INACTIVITY AND SERVICE RESTART

In case of prolonged inactivity of the ro- bot, it is necessary to carry out a series of operations to assure its correct func- tioning when it is reused.

ble by unfamiliar people (children, animals, etc.). 4-Disconnect the plug of the power supply unit.

1-Clean the robot properly (see "Robot cleaning") 2-Carry out battery recharge at least once a month for lead batteries and every 5 months for lithium batteries (see "Battery recharge") 3-Place the robot in a safe and dry place, at a suitable room tempera- ture 10-30 °C and not easily reacha-

Service restart Before restarting the robot after a long inactivity, proceed as shown.

1-Connect the plug of the power supply unit. 2-Carry out battery recharge (see "Bat- tery recharge")

RECOMMENDATIONS FOR USE

Here below are some indications to fol- low during the use of the robot. – Even after a proper reading of instruc-

– If the lawn is set up with an automatic

watering installation, programme it so that, at the beginning of watering, the robot has already completed the trimming of the area (start it at least 6 hours before watering). – Check the ground gradient and make

tions, at its first use, simulate some test moves to detect the controls and the main functions. – Make sure the fixing screws of the

main parts are tightened properly. – Carry out a frequent trimming of the

sure that it does not exceed the maxi- mum values allowed so that the use of the robot does not cause dangers.

lawn to avoid an excessive growing of the grass. – Do not use the robot to trim grass

higher than 10 cm.

ORDINARY MAINTENANCE

RECOMMENDATIONS FOR MAINTENANCE

Before performing maintenance opera- tions, make sure that the robot has stopped in safety conditions (see "Ro- bot safety stop").

Page 33 of the Ambrogio Basic user manual — ROBOT CLEANING
Page 33 · cliquer pour agrandir
Page 33

PROGRAMMED MAINTENANCE INTERVALS CHART

Frequency Component Type of intervention Reference

Check the chain tension see “Chain tension adjustment” Controllare la tensione delle catene

Every month Wheel drive

Clean and check the ef- ficiency of the blade

see “Robot clean- ing” If the blade is bent due to an impact or if it is worn-out, replace it

see “Replace the blade”

Clean and remove any oxidations see “Robot cleaning”

Robot Carry out cleaning see “Robot cleaning”

ROBOT CLEANING

1-Clean all the outside surfaces of the robot with a sponge soaked in warm water and neutral soap and rinse properly. 2-Do not use solvents or benzine so not to damage the varnished surfaces and the plastic components. 3-Do not wash the inside parts of the robot and do not use water jets in pressure so not to damage the elec- tric and the electronic components.

4-Check the lower part of the robot (cutting blade area and wheels) and remove the deposits and/or resi- dues that might obstruct the correct functioning of the robot. To remove the deposits and/or oth- er residues from the blade, use a suitable brush.

5-Clean the battery recharge knobs and remove any deposits due to elec- tric contacts with a dry cloth and, if necessary, with fine-grained abrasive paper.

Every week Blade · Battery recharge knobs · Every week

Page 34 of the Ambrogio Basic user manual — PROGRAMMED MAINTENANCE INTERVALS CHART
Page 34 · cliquer pour agrandir
Page 34
Ambrogio Basic — PROGRAMMED MAINTENANCE INTERVALS CHART diagram (page 34)
Fig. 41

1-Stop the robot in safety condi- tions (see "Robot safety stop"). 2-Undo the knobs (A). 3-Remove the hood (B).

4-Undo the screws (C) and re- move the body cover (D) on both sides. 5-Lubricate chains.

6-Reassemble body cover (D) and tighten screws (C).

Page 35 of the Ambrogio Basic user manual — A
Page 35 · cliquer pour agrandir
Page 35

FAILURES, CAUSES AND SOLUTIONS

TROUBLESHOOTING

The purpose of the following information is to identify and correct possible faults and malfunctions that may occur when using the machine. Some failures may be resolved by the us-

er; others require precise technical skills or special abilities and must be exclusive- ly resolved by qualified personnel with certified experience, achieved in the spe- cific intervention field.

Problem Causes Solutions The robot is very noisy Damaged cutting blade Replace the blade with a new one. The robot stopped with the led (E) (green) on and the led (H) (yellow) flashing.

The perimeter wire is not correctly connected (bro- ken wire, lack of electric connection, etc.).

Check that the power supply works and that the connec- tion of the power supply-trans- mitter unit is correct.

E F

Ambrogio Basic — E F diagram (page 35)
Fig. 42

Excessive ground slope. Mark the area with excessive gradient.

Check that the wire is in- stalled properly (too deep, close to metal objects, dis- tance between the wire that marks two elements less than 70 cm, etc.). Perimeter wire marking inside areas (beds, bush- es, etc.) placed clockwise.

Perimeter cable incor- rectly placed.

D

G H B M

The robot stopped with the led (F) (red) flashing and the led (H) (yellow) on.

A

Relocate the perimeter wire correctly (anticlockwise direc- tion).

Adopt suitable solutions to re- duce the temperature of the power supply unit (air or change the installation area, etc.). The wheel drive is not correct

Overheated power supply unit

Check and, if necessary, ad- just the chain tensioning.

Page 36 of the Ambrogio Basic user manual — A
Page 36 · cliquer pour agrandir
Page 36

Cutting blade with depos- its and/or residues Clean the cutting blade

Cutting blade worn out Replace the blade with an original spare part. Working area too big compared to the actual capacity of the robot.

The working area is not completely trimmed

Ad just the working area (see "Specifications")

Batteries are about to deplete their life cycle.

Replace the batteries with original spare part. The batteries do not re- charge completely.

Recharge the batteries for at least 12 hours

Power supply break to the transmitter Restart the robot

The robot stopped with the led (F) (red) and (H) (yel- low) flashing.

Adopt suitable solutions to re- duce the temperature of the power supply unit (air or change the installation area, etc.). The wheel drive is not correct

Overheated power supply unit

Check and, if necessary, ad- just the chain tensioning.

E F

Damaged cutting blade Replace the blade with an original spare part.

Remove the flood cause from the blade.

Cutting blade flooded by residues (tapes, ropes, plastic fragments, etc.).

D

G H B M

A

The robot stopped with the led (F) (red) flashing and the led (G) (blue) on. Blade motor error

Stop the robot in safety condi- tions (see "Robot safety stop"). Remove the obstacles and re- start the robot (see "Manual start and stop of the robot")

Get the motor repaired or re- placed by the nearest author- ized Assistance centre.

The wheel drive is not correct

Check and, if necessary, ad- just the chain tensioning.

The robot stopped with the leds (F) (red ) and (G) (blue) flashing. Wheel motor er- ror

Check that the lawn to trim is even, and without pits, stones or other obstacles. If so, per- form the necessary clear- ance operations. One or both motors, starting the wheel trans- mission, in breakdown.

Rough ground or with ob- stacles that hinder move- ment.

Get the motor repaired or re- placed by the nearest author- ized Assistance centre.

Problem Causes Solutions · Electrical motor malfunc- tion

Page 37 of the Ambrogio Basic user manual — D
Page 37 · cliquer pour agrandir
Page 37

The robot stopped with the led (F) (red) flashing, and the leds (H) (yellow) and (G) (blue) on. Shock sensors error

The shock sensors are blocked

Remove the hood and check that the sensors are functioning.

Insufficient width of the working area

Increase the width of the work- ing area. Minimum value 70 cm

Check that the lawn to trim is even, and without pits, stones or other obstacles. If so, per- form the necessary clear- ance operations. (see "Arrangement and marking of the working area")

The wheels go idle, as they are raised from the ground.

The robot stopped with the led (F) (red) flashing. Key- board or drive wheels error.

Contact an Assistance Cen- tre authorized by the Manu- facturer

E F

Check that the position of the cursor (M) matches with the power voltage and that the push button (B) is on "ON". Check that the power supply unit is correctly connected to the power socket.

There is no power volt- age

The led (L) of the power supply unit does not turn on.

D

G H B M

A

Get the fuse replaced by the nearest authorized Assist- ance centre.

Stop the robot in safety condi- tions (see "Robot safety stop") Press the button (B) of the power supply unit on OFF. Carry out the joint of the pe- rimeter wire. The led (A) (or- ange) of the trans- mitter turns on repeatedly with consecutive flash- es (less than 4).

The led (A) (green) of the transmitter is on.

Perimeter wire too long. Install the signal amplification

kit.

Perimeter wire damaged or oxidized.

Check any joints. if necessary, replace the wire.

The led (A) (red) of the transmitter is on.

Get the check carried out by the nearest authorized As- sistance centre.

Connections not per- formed correctly.

Show 4 more labels / short text on this page
Problem Causes Solutions · Keyboard error · Blown fuse · Interrupted perimeter wire
Page 38 of the Ambrogio Basic user manual — FAILURES, CAUSES AND SOLUTIONS
Page 38 · cliquer pour agrandir
Page 38
Ambrogio Basic — FAILURES, CAUSES AND SOLUTIONS diagram (page 38)
Fig. 43

to the Assistance Service if such incon- veniences are not illustrated and de- scribed in the manual.

Ambrogio Basic — FAILURES, CAUSES AND SOLUTIONS diagram (page 38)
Fig. 44

1-Stop the robot in safety condi- tions (see "Robot safety stop") 2-Undo the knobs (A). 3-Remove the hood (B).

4-Disconnect the connectors (C). 5-Unscrew the screws (D) and remove the guard (E).

Ambrogio Basic — FAILURES, CAUSES AND SOLUTIONS diagram (page 38)
Fig. 45
Page 39 of the Ambrogio Basic user manual — LITHIUM BATTERY
Page 39 · cliquer pour agrandir
Page 39

6-Undo the screws (F) and re- move the brackets (G).

Ambrogio Basic — FAILURES, CAUSES AND SOLUTIONS diagram (page 39)
Fig. 46

screw (F) bracket (G)

LEAD BATTERY

1-Disconnect the cables in se- quence (N-L-P). 2-Remove the battery (H) and fit the replacement. 3-Perform the same operations to replace the other battery (H). 4-Reconnect the cables in se- quence (L-P-N).

cable (P) cable (N)

LITHIUM BATTERY

1-Disconnect the cables in se- quence (S-R). 2-Remove the battery (Q) and fit the replacement. 3-Perform the same operations to replace the other battery (if present). 4-Reconnect the cables in se- quence (R-S).

Show 15 more labels / short text on this page
bracket (G) · Lead battery · cable (L) · battery (H) · battery (H) · connector (M) · cable (L) · Lithium battery · cable (S) · battery (Q) · connector (M) · battery (Q) · cable (R) · cable (R) · cable (S)
Page 40 of the Ambrogio Basic user manual — FAILURES, CAUSES AND SOLUTIONS
Page 40 · cliquer pour agrandir
Page 40
Ambrogio Basic — FAILURES, CAUSES AND SOLUTIONS diagram (page 40)
Fig. 47

1-Assemble brackets (G) and fix them with screws (F). 2-Reassemble body cover (E) and tighten screws (D). 3-Connect the connectors (C).

Page 41 of the Ambrogio Basic user manual — ROBOT DISPOSAL
Page 41 · cliquer pour agrandir
Page 41

REPLACE THE BLADE

1-Stop the robot in safety condi- tions (see "Robot safety stop"). 2-Turn the robot upside down. Lay it on a compact surface and such not to damage the body. 3-Remove the screws (V) to re- move the blade (U). 4-insert the new blade and fas- ten screws.

Ambrogio Basic — REPLACE THE BLADE diagram (page 41)
Fig. 48

5-Capsize the robot to take it back to its normal position.

ROBOT DISPOSAL

vant legislation in force (see "Safety for man and the environment during dis- posal")

blade (U) · screw (V) · blade (U)

Page 42 of the Ambrogio Basic user manual — REPLACE THE BLADE
Page 42 · cliquer pour agrandir
Page 42
Page 42 of the Ambrogio Basic user manual — REPLACE THE BLADE
Dépannage

Dépannage

Problèmes fréquents, causes probables et solutions.

ProblèmeCause possibleSolution
The robot is very noisyDamaged cutting bladeReplace the blade with a new one. p.35
The robot stopped with the led (E) (green) on and the led (H) (yellow) flashing.The perimeter wire is not correctly connected (bro- ken wire, lack of electric connection, etc.).Check that the power supply works and that the connec- tion of the power supply-trans- mitter unit is correct. p.35
The robot stopped with the led (E) (green) on and the led (H) (yellow) flashing. p.35
The robot stopped with the led (F) (red) flashing and the led (H) (yellow) on.Excessive ground slope.Mark the area with excessive gradient. p.35
The robot stopped with the led (F) (red) flashing and the led (H) (yellow) on.Perimeter cable incor- rectly placed.Check that the wire is in- stalled properly (too deep, close to metal objects, dis- tance between the wire that marks two elements less than 70 cm, etc.). p.35
The robot stopped with the led (F) (red) flashing and the led (H) (yellow) on.Perimeter wire marking inside areas (beds, bush- es, etc.) placed clockwise.Relocate the perimeter wire correctly (anticlockwise direc- tion). p.35
The robot stopped with the led (F) (red) flashing and the led (H) (yellow) on.Overheated power supply unitAdopt suitable solutions to re- duce the temperature of the power supply unit (air or change the installation area, etc.). p.35
The robot stopped with the led (F) (red) flashing and the led (H) (yellow) on. p.35
The robot stopped with the led (F) (red) flashing and the led (H) (yellow) on.The wheel drive is not correctCheck and, if necessary, ad- just the chain tensioning. p.35
The working area is not completely trimmedCutting blade with depos- its and/or residuesClean the cutting blade p.36
The working area is not completely trimmedCutting blade worn outReplace the blade with an original spare part. p.36
The working area is not completely trimmedWorking area too big compared to the actual capacity of the robot.Ad just the working area (see "Specifications") p.36
The working area is not completely trimmedBatteries are about to deplete their life cycle.Replace the batteries with original spare part. p.36
The working area is not completely trimmedThe batteries do not re- charge completely.Recharge the batteries for at least 12 hours p.36
The robot stopped with the led (F) (red) and (H) (yel- low) flashing.Power supply break to the transmitterRestart the robot p.36
The robot stopped with the led (F) (red) flashing and the led (G) (blue) on. Blade motor errorDamaged cutting bladeReplace the blade with an original spare part. p.36
The robot stopped with the led (F) (red) flashing and the led (G) (blue) on. Blade motor errorCutting blade flooded by residues (tapes, ropes, plastic fragments, etc.).Remove the flood cause from the blade. p.36
The robot stopped with the led (F) (red) flashing and the led (G) (blue) on. Blade motor errorUse protection gloves to avoid the risk of cuts on han- ds. p.36
The robot stopped with the led (F) (red) flashing and the led (G) (blue) on. Blade motor errorThe start of the robot oc- curred with obstacles be- ing too close (less than m away) or in presence of unexpected obstacles (fallen branches, forgot- ten objects, etc.).Stop the robot in safety condi- tions (see "Robot safety stop"). Remove the obstacles and re- start the robot (see "Manual start and stop of the robot") p.36
The robot stopped with the led (F) (red) flashing and the led (G) (blue) on. Blade motor errorElectrical motor malfunc- tionGet the motor repaired or re- placed by the nearest author- ized Assistance centre. p.36
The robot stopped with the leds (F) (red ) and (G) (blue) flashing. Wheel motor er- rorThe wheel drive is not correctCheck and, if necessary, ad- just the chain tensioning. p.36
The robot stopped with the leds (F) (red ) and (G) (blue) flashing. Wheel motor er- rorRough ground or with ob- stacles that hinder move- ment.Check that the lawn to trim is even, and without pits, stones or other obstacles. If so, per- form the necessary clear- ance operations. p.36
The robot stopped with the leds (F) (red ) and (G) (blue) flashing. Wheel motor er- rorOne or both motors, starting the wheel trans- mission, in breakdown.Get the motor repaired or re- placed by the nearest author- ized Assistance centre. p.36
The robot stopped with the led (F) (red) flashing, and the leds (H) (yellow) and (G) (blue) on. Shock sensors errorThe shock sensors are blockedRemove the hood and check that the sensors are functioning. p.37
The robot stopped with the led (F) (red) flashing, and the leds (H) (yellow) and (G) (blue) on. Shock sensors errorInsufficient width of the working areaIncrease the width of the work- ing area. Minimum value 70 cm p.37
The robot stopped with the led (F) (red) flashing. Key- board or drive wheels error.The wheels go idle, as they are raised from the ground.Check that the lawn to trim is even, and without pits, stones or other obstacles. If so, per- form the necessary clear- ance operations. (see "Arrangement and marking of the working area") p.37
The robot stopped with the led (F) (red) flashing. Key- board or drive wheels error.Keyboard errorContact an Assistance Cen- tre authorized by the Manu- facturer p.37
The led (L) of the power supply unit does not turn on.There is no power volt- ageCheck that the position of the cursor (M) matches with the power voltage and that the push button (B) is on "ON". Check that the power supply unit is correctly connected to the power socket. p.37
The led (L) of the power supply unit does not turn on.Blown fuseGet the fuse replaced by the nearest authorized Assist- ance centre. p.37
The led (A) (green) of the transmitter is on.Interrupted perimeter wireStop the robot in safety condi- tions (see "Robot safety stop") Press the button (B) of the power supply unit on OFF. Carry out the joint of the pe- rimeter wire. p.37
The led (A) (green) of the transmitter is on. p.37
The led (A) (or- ange) of the trans- mitter turns on repeatedly with consecutive flash- es (less than 4).Perimeter wire too long.Install the signal amplification kit. p.37
The led (A) (or- ange) of the trans- mitter turns on repeatedly with consecutive flash- es (less than 4).Perimeter wire damaged or oxidized.Check any joints. if necessary, replace the wire. p.37
The led (A) (red) of the transmitter is on.Connections not per- formed correctly.Get the check carried out by the nearest authorized As- sistance centre. p.37

Poser une question sur : Ambrogio Basic

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Ambrogio Basic

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Ambrogio Basic manuel PDF

255 pages·6.1 MB·Tondeuse à gazon·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…