

User’s Manual No. 980344-001 Rev. A
©2001 Zebra Technologies Corporation

This document contains information proprietary to Zebra Technologies Corporation. This docu- ment and the information contained within is copyrighted by Zebra Technologies Corporation and may not be duplicated in full or in part by any person without written approval from Zebra Technol- ogies Corporation. While every effort has been made to keep the information contained within cur- rent and accurate as of the date of publication, no guarantee is given or implied that the document is error-free or that it is accurate with regard to any specification. Zebra Technologies Corporation reserves the right to make changes, for the purpose of product improvement, at any time.
LP2722, TLP2722, LP2742, TLP2742 and TLP3742 are service marks and Zebra is a trademark of Zebra Technologies Corporation. Windows and MS-DOS are registered trademarks of Microsoft Corp. All other marks are trademarks or registered trademarks of their respective holders.
FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109(a) Class B digital device
Supplemental Information: This device complies with Part 15 of the FCC Rules. Operation is subject to the following Two Con- ditions: (1) This device may not cause harmful interference , and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device complies with Industry Canada ICS-003 class B requirements.
Cet equipement est conforme a l’ICS-003 classe B de la norm Industrielle Canadian
ii 980344-001 Rev.A


This page describes general safety and maintenance warnings and cautions for the printer and are referenced throughout the manual.
The printer should never be operated in a location where it can get wet. Personal injury could result.
The discharge of electrostatic energy that accumulates on the surface of the human body or other surfaces can damage or destroy the print head or electronic components used in this device. DO NOT TOUCH the print head or the electronic components under the print head assembly.
1)When installing or modifying the printer setup or configuration, ALWAYS TURN POWER OFF Before:
A) Connecting any cables. B) Performing any cleaning or maintenance operations. C) Moving the printer.
Always use high quality approved labels and tags. If adhesive backed labels are used that DO NOT lay flat on the backing liner, the exposed edges may stick to the label guides and rollers inside the printer, causing the label to peel off from the liner and jam the printer.
If you should run out of labels while printing, DO NOT turn the power switch OFF (0) while reloading or data loss may occur. The printer will automatically resume printing when a new label or ribbon roll is loaded.
Print density (darkness) is affected by the heat energy (density setting) applied and by the print speed. Changing both Print Speed and Density may be required to achieve the desired results.
iv 980344-001 Rev.A

This section provides information on the instal- lation and operation of the printer.
The printer is a low cost, desktop thermal bar code printer. LP models are direct thermal. TLP modes are thermal transfer and direct thermal printers. This family of printers is specifically de- signed for printing labels, tags or continuous re- ceipts (with or without bar codes) from a DOS™, Windows™or ASCII-based compatible computer.





Installation The following steps will guide you through the installation of the printer, media and software.



Serial Interface



You must remove the outside length of media (that is, one, full revolution of labels and any liner). When you remove this part of the media, you remove the oils, dust, and adhesives that contaminate it. Tape or adhesive holds the loose end and the outside length of media becomes contaminated when handled or stored.
Printer

You must avoid dragging adhesive or dirty media between the print head and platen. Such an occurrence damages the print head and is not covered under your warranty. Using clean media prevents damage and reduces wear on the print head and platen.












If the indicator fails to light, refer to Appendix A - Trouble Shooting.

Run the AutoSense routine.


Image buffer size:245K Fmem:000,0K,019.9K avl Gmem:000K,0241K avl E I8,0,001 rY S8 D12 R032,000 ZT UN q0450 Q0800,034 Option:D 11 12 13 now in DUMP

Insert Printer
CD ROM
Start your computer and follow the installation instructions on the compact disc (CD).


Face Print Surface UP
Insert & Load
Media


Label Dispenser Printers with an optional label taken sensor can dispense a single peeled label. Remove the label to automatically print the next label.




Close Cover
Push to Open Label Taken Sensor
Press FEED Button
Remove Presented
Label

This feature is supported on TLP model printers, only.

Print Head Mechanism


Open Print Head

Load Transfer Ribbon
Start Ribbon
Open Print Head
(Rear View)
Pull Ribbon Around
Print Head




Problem Solution or Reason
POWER indicator does not light GREEN when power switch is turned to ON (1) position.
POWER indicator lights GREEN, but printer will not print.
Printer appears to be working (media is being fed out), but nothing is printed.
Printing is faded or poor quality.
Prints only partial label or skips a label.
Printing stops and POWER indicator lights ORANGE or RED.



The printer has flash (non-volatile) memory to store printer configuration settings. The settings are stored in flash memory and are set by programing, printer drivers or the AutoSense routine. The settings are shown on the Dump mode printout or can be reported back to the host via the serial port.
The following are the basic settings stored in the printer:
PrintMode-Direct(OD)orThermalTransfer(O) Speed (S) Density (D) or heat applied Form (label) length and gap in dots (Q) Form (label) width in dots (q) Serial Port (Y) Margin (R) Buffer Mode (r)
Print Mode is Direct Thermal (OD)

Printout
(See the U command in the Programmer’s manual
for details)

The printer’s serial port is configured with the Y command for the printer. The printer supports interface data rates from 1200 to 38,400 baud. See the programmer's manual for details.
The printer’s serial port default configuration is:
9600 baud 8 bit data 1 stop bit No parity
The figure below displays the cable wiring re- quired to use the printer’s serial interface.
Printer Host
1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9
DTR
N/C
GND
GND
DSR
RDY
RTS
N/C
CTS
RDY
RI
N/C
Female DB-9 to Male DB-9
1 8 2 3 3 2 4 20 5 7 6 6 7 4 8 5 9 22
N/C
GND
GND
DSR RTS
RDY
N/C
CTS
N/C RDY
RI
Female DB-25 to Male DB-9
*+5 volts at 150 mA for external device (e.g. KDU or scanner)

The figure below displays the cable wiring required to use the printer's Centronics parallel interface.
PRINTER DB-25 Pin No.
Pin No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
DATA 0 DATA 1 DATA 2 DATA 3 DATA 4 DATA 5 DATA 6 DATA 7
DATA 0 DATA 1 DATA 2 DATA 3 DATA 4 DATA 5 DATA 6 DATA 7
ACK/ BUSY PAPER ERR.
ACK/ BUSY PAPER ERR.
READY
INIT ERROR/
INIT ERROR/
N/A N/A N/A SIG. GND SIG. GND SIG. GND SIG. GND SIG. GND SIG. GND SIG. GND
N/A N/A +5V SIG. GND SIG. GND SIG. GND SIG. GND SIG. GND SIG. GND
(Cable)
+5 volts at 300 mA for external device (e.g. PrintServer)
Centronics


Problèmes fréquents, causes probables et solutions.
| Problème | Cause possible | Solution | |
|---|---|---|---|
| POWER indicator does not light GREEN when power switch is turned to ON (1) position. | 1. Check power connections from A.C. outlet to power supply to printer. | p.25 | |
| POWER indicator lights GREEN, but printer will not print. | 1. Check interface cable connections from computer to printer. | p.25 | |
| Printer appears to be working (media is being fed out), but nothing is printed. | 1. Verify that the labels are the correct type (direct thermal). 2. Check that the roll is loaded with the di- rect thermal side facing up. 3. Clean the print head with cleaning pen. 4. For TLP models, check that the ribbon is properly installed. | p.25 | |
| Printing is faded or poor quality. | 1. Clean the print head with cleaning pen. 2. Adjust print speed/darkness in software. | p.25 | |
| Prints only partial label or skips a label. | 1. Perform AutoSense gap sensor adjustment on page 13. 2. Label caught on print head. 3. Print head is not properly latched. 4. Possible software problem. Check the printer memory configuration. Refer to the EPL2 Programming manual. | p.25 | |
| Printing stops and POWER indicator lights ORANGE or RED. | 1. Perform AutoSense gap sensor adjust- ment on page 13. 2. Possible problem with label stock. Use only approved labels and tags. 3. Possible label jam. 4. Insufficient memory for label size. Check the printer memory configuration. 5. Possible software problem. Refer to the EPL2 Programming manual. | p.25 |
Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.
Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.