Manuel d'utilisation / d'entretien du produit W1672 du fabricant Woodstock
Aller à la page of 45
INSTRUCTION MANUAL MODEL W1672 14" BANDSAW Phone: 1-360-734-3482 • On-Line Technical Support: tech-support@woodstockint.com COPYRIGHT © 2001 BY WOODSTOCK INTERNATIONAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
1 Table Of Contents PAGE 1. INTRODUCTION ..............................................................................................2 ABOUT YOUR NEW BANDSAW ......................................................................2 WOODSTOCK SERVICE AND SUPPORT .
2 INTRODUCTION ABOUT YOUR NEW BANDSAW This new Shop Fox ® Bandsaw has been specially designed by Woodstock International, Inc. to provide many years of trouble free service. Close attention to detail, ruggedly built parts and a rigid quality con- trol program assure safe and reliable operation.
3 WARRANTY AND RETURNS Machine Specifications Max. Cutting Width ............................................................................13 1 ⁄ 2 '' Max. Cutting Height ..................................................................
4 READ MANUAL BEFORE OPERATING MACHINE FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL RESULT IN PERSONAL INJURY SAFETY FIRST! 1. Thoroughly read the instruction manual before operating your machine. Learn the applications, limitations and potential hazards of this machine.
5 1. Do not operate bandsaw without wheel covers, pulley covers or blade guards in place. 2. Blade replacement, machine adjustments and maintenance are to be done with machine turned off and unplugged. Allow all moving parts to come to a complete stop before doing any of the above.
6 This equipment must be grounded. Verify that any existing electrical outlet and cir- cuit you intend to plug into is actually grounded. If it is not, it will be necessary to run a separate 12 A.W.G. copper grounding wire from the outlet to a known ground.
7 This equipment must be grounded. Verify that any existing electrical outlet and circuit you intend to plug into is actually grounded. If it is not, it will be necessary to run a sep- arate 12 A.W.G. copper grounding wire from the outlet to a known ground.
AVOIDING POTENTIAL INJURIES 8 Figure 3. Unplug saw before changing blades. Figure 6. Use push sticks whenever possible. Figure 4. Never start motor with covers open.
AVOIDING POTENTIAL INJURIES 9 Figure 9. Use relief cuts for tight curves. Figure 7. Use push blocks when necessary. Figure 8. Never place hands in line of cut.
10 Figure 10. Components laid out for identification. The following is a description of the components shipped with the Shop Fox ® W1672 14" Bandsaw. It is recommended that the components be laid out in a similar fashion to those in Figure 10 . This will help in identification before beginning assembly.
11 While the main components of the Shop Fox ® W1672 14" Bandsaw are assembled at the facto- ry, some assembly is required. The following is the recommended sequence best suited for final assembly. Stand Hardware Figure 11. Bandsaw stand. Do not connect the machine to power at this time.
12 Figure 13. Securing bandsaw body. Figure 12. Lifting tensioning handle. Bandsaw Body 1. Seek assistance and place the bandsaw body next to the stand. Rotate the bandsaw body so the access door on the bandsaw body is facing the same way as the cabinet door.
13 Figure 14. Installing pulley on motor. Figure 15. Installing motor. Mounting Motor 1. Make sure the key is in place in the keyway on the motor shaft. Align the keyway and slide the motor pulley onto the motor shaft as far as it will go. Figure 14 .
14 Mounting Table The table is secured to the bandsaw by two trunnions mounted to its bottom surface. These, in turn, have threaded studs that work to lock the table’s angle with respect to the blade. In order to mount the table, you must first mount the trunnion support.
15 Figure 20. Rail placement. Figure 22. Securing rail with cap screw. Figure 21. Rail assembly. Figure 23. Starting fence on rail. Fence/Rails The fence is secured to the table with 2 rails. The rails are fastened to the front and back edges of the table with 4 socket head cap screws and spacer sleeves.
16 ADJUSTMENTS Location of Controls Take the time to familiarize yourself with the controls of your new bandsaw. They will be fre- quently mentioned throughout the instructions in this manual, and the better you know your machine, the better you can make it perform.
17 Speed Changes Figure 27. Diagram of speed options. Figure 28. Speed pulley (lower wheel removed for clarity). The speed diagram in Figure 27 is included to help illustrate belt positions necessary to pro- duce the available speeds. Select the proper speed for the job at hand and move the belts to the desired location.
18 Figure 30. Sliding blade through table slot. Figure 29. Removing table insert. To remove the blade: 1. Remove the table insert as in Figure 29 . 2. Pull out the steel pin at the end of the blade slot in the table. 3. Loosen the guide blocks by turning the thumbscrews counterclockwise and retract guide blocks away from the blade.
19 Blade Tension Figure 31. Checking blade deflection. Blade tension is one of the most critical factors in the performance of your bandsaw. The blade must be tight enough so it does not sway during a cut, yet stay flexible enough to bend around the wheels.
20 Tracking Figure 32. Blade centered on wheel. Tracking the blade means positioning it on the wheels so it will not come off during operation. This is usually done by adjusting the tilt of the upper wheel. Blade tracking is one of the most important adjustments you can make for optimal perfor- mance of your bandsaw.
21 Wheel Alignment Figure 34. Checking for coplanarity. Figure 33. Dimensions of coplanarity gauge. Wheel alignment is one of the most critical fac- tors for optimal performance from your bandsaw.
6. If the wheels will go parallel but not copla- nar, then move the lower wheel at the adjustment hub ( Figure 35) as necessary. 7. The adjustment hub allows you to move the lower wheel in the desired direction. Turning all the bolts clockwise in equal amounts pushes the wheel forward.
23 Blade Guides In order to stabilize the blade during use, it is important that the guide blocks and rear support bearings are monitored and adjusted regularly for optimum blade life and high quality cuts. The rear support bearings keep the blade straight during a cut.
24 Figure 39. Guide block position on blade. Figure 40. Guide block position on blade. The upper and lower guide blocks reduce side-to- side blade wander during cutting. Proper adjust- ment of these will also minimize heat and increase blade life. To adjust the guide blocks: 1.
25 Table Adjustments Figure 41. Positive stop with lock nut. Figure 42. Squaring table to blade. Figure 43. Pointer set to zero. The table can be adjusted 45° to the right or 10° to the left. There is a positive stop bolt ( Figure 41 ) that mounts to the body, under the table.
26 Table Adjustments Cont. Figure 45. Squaring miter slot to blade. Figure 44. Six trunnion bolts under table. It is important to verify that the miter gauge slot is parallel to the blade. This will ensure straight cuts when using your miter gauge and the fence.
27 Fence Adjustments There are two knobs on the fence. 1. The long handle to the side of the fence allows you to clamp (turning clockwise) the rear of the fence. See Figure 46. 2. The smaller knob below the rear lock knob is the front knob. This locks (also turning clockwise) the front of the fence in place.
Figure 47. This rip cut illustrates excessive blade lead. 28 Blade Lead An inherent situation with all bandsaws is their tendency to not cut parallel to the fence, even when the fence seems parallel to the blade. Figure 47 demonstrates the effect blade lead can have on your workpiece.
29 OPERATIONS Once assembly is complete and adjustments are done to your satisfaction, you are ready to start the machine. Make sure the starting switch is off. The pad- dle down means the machine is off. Make sure all the fasteners and lock handles are tight.
30 Ripping Crosscutting Figure 49. Ripping a board. Figure 50. Crosscutting a board. Always wear safety glasses when operating the bandsaw. Failure to comply may result in serious personal injury. “Ripping” means cutting along the grain of the wood.
31 Figure 51. Minimum radii for blade widths. Figure 52. Relief cuts before cutting curves. Cutting Curves The ability to cut curves is one of the most use- ful things a bandsaw can accomplish. However, when cutting curves you need to be careful not to twist the blade, especially when cutting tight curves.
32 Always wear safety glass- es when operating the bandsaw. Failure to comply may result in serious personal injury. Stacked Cuts Another useful operation for the bandsaw is making stacked cuts. See Figure 54. These cuts provide uniformity to multiple pieces.
33 Blade Selection Figure 55. Types of blade teeth. Blade Width As a general rule, large blades provide more support for thick stock and allow you to cut straighter. Small blades provide maximum con- trol for cutting tight curves, but are not a good choice for cutting straight cuts and do not have the strength for thick stock.
34 MAINTENANCE Lubrication Since all bearings are shielded and permanently lubricated, simply leave them alone until they need to be replaced. Do not lubricate them. For other items on this machine, such as the guide column, an occasional application of light machine oil is all that is necessary.
35 Maintenance Notes Maintenance Schedule • Every 2 Hours of Running Time: Clean and lubricate table top, miter slot and fence. • Every 3 Hours of Running Time: Check blade tracking, guide column and table-to-blade. Check gap on guide blocks and thrust bearings.
36.
37 The following pages contain general machine d a t a, parts diagrams/lists and warranty/return information for your Shop Fox ® Model W1672 14" Bandsaw. If you need parts or help in assembling your machine, or if you need operational informa- tion, we encourage you to call our Service Department.
38.
39.
40.
41 101 XPB03 HEX BOLT 5 ⁄ 16 "-18 X1" 102 XPW07 FLAT WASHER 5 ⁄ 16 " 103 X1672103 SPRING 104 X1672104 BRACKET 105 X1672105 BAR SETTING PLATE 107 X1672107 SPECIAL WASHER 108 X1672108.
42 315 XPB12 HEX BOLT 5 ⁄ 16 "-18 X 1 1 ⁄ 4 " 316 X1672316 TABLE BRACKET 317 X1672317 TABLE LOCKING KNOB 318 X1672318 UPPER BRACKET 319 X1672319 BEARING BRACKET 320 XP6200 BEARING 6200Z .
CUT ALONG DOTTED LINE 10. What stationary woodworking tools do you own? Check all that apply. ___Air Compressor ___Panel Saw ___Band Saw ___Planer ___Drill Press ___Power Feeder ___Drum Sander ___Radi.
TAPE ALONG EDGES--PLEASE DO NOT STAPLE FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE WOODSTOCK INTERNATIONAL, INC. P.O. BOX 2309 BELLINGHAM, WA 98227-2309 Place Stamp Here.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Woodstock W1672 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Woodstock W1672 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Woodstock W1672, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Woodstock W1672 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Woodstock W1672, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Woodstock W1672.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Woodstock W1672. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Woodstock W1672 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
