FR
Wolf logo
Notice d'utilisation officielle

Wolf Multi-Function Cooktop

63 pages·776 KB·Table de cuisson·PDF·ENNLJA
Wolf Multi-Function Cooktop
Table des matières 23 sections MULTI-FUNCTION COOKTOP · INSTALLATION INSTRUCTIONS · INSTRUCCIONES DE INSTALACIÓN · INSTRUCTIONS D’INSTALLATION · … AfficherMasquer
Page 1 of the Wolf Multi-Function Cooktop user manual — INSTRUCCIONES DE INSTALACIÓN
Page 1 · cliquer pour agrandir
Page 1

MULTI-FUNCTION COOKTOP

INSTALLATION INSTRUCTIONS

INSTRUCCIONES DE INSTALACIÓN

INSTRUCTIONS D’INSTALLATION

ISTRUZIONI PER L’INSTALLAZIONE

INSTALLATIONSANWEISUNGEN

Page 2 of the Wolf Multi-Function Cooktop user manual — E N G L I S H 4
Page 2 · cliquer pour agrandir
Page 2

E N G L I S H 4

E S P Ã N O L 1 6

F R A N Ç A I S 2 8

I TA L I A N O 4 0

D E U T S C H 5 2

Page 3 of the Wolf Multi-Function Cooktop user manual — E N G L I S H 4
Page 3 · cliquer pour agrandir
Page 3

C O N TA C T I N F O R M AT I O N

Websitewolfappliance.com

As you follow these instructions, you will notice WARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Wolf equip- ment. There are two types of potential hazards that may occur during installation.

signals a situation where minor injury or product damage may occur if you do not follow instructions.

states a hazard that may cause serious injury or death if precautions are not followed.

Another footnote we would like to identify is IMPORTANT NOTE: This highlights informa- tion that is especially relevant to a problem- free installation.

WOLF® is a registered trademark of Wolf Appliance, Inc.

Page 4 of the Wolf Multi-Function Cooktop user manual — WHAT TO DO IF YOU SMELL GAS:
Page 4 · cliquer pour agrandir
Page 4

INSTALLATION R E Q U I R E M E N T S

Wolf Multi-Function Cooktop — ICBIM15/S diagram (page 4)
Fig. 1

If the information in this book is not followed exactly, a fire or explosion may result, causing property damage, personal injury or death.

Installer: Please read the entire Installation Instructions prior to installation. Save these instructions for the local inspector’s refer- ence, then leave them with the homeowner.

R AT I N G P L AT E I N F O R M AT I O N

Homeowner: Please read and keep these instructions for future reference and be sure to read the entire Use & Care Information prior to use.

ICBIM15/S

IMPORTANT NOTE:

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

A ventilation hood or downdraft system is recommended (but not required) for use with the Wolf gas multi-function cooktop.

Record the model and serial numbers before installing the cooktop. Both numbers are listed on the rating plate, located on the underside of the cooktop. Refer to the illustration below.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electrical switch.

Do not use any phone in your building.

Wolf Multi-Function Cooktop — WHAT TO DO IF YOU SMELL GAS: diagram (page 4)
Fig. 2

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

Model Number · Serial Number · Rating plate location

Page 5 of the Wolf Multi-Function Cooktop user manual — BEFORE YO U S TA RT
Page 5 · cliquer pour agrandir
Page 5

BEFORE YO U S TA RT

Proper installation is your responsibility. Have a qualified technician install this cooktop. You must also ensure that electri- cal installation is adequate and in compli- ance with all local codes and ordinances.

Check the location where the cooktop will be installed. The location should be away from strong draft areas, such as windows, doors and strong heating vents or fans. Do not obstruct flow of combustion and ventilation air.

Please check the product rating plate or Use & Care Information for type of gas needed.

Make sure you have everything necessary for correct installation. It is the responsibil- ity of the installer to comply with the instal- lation clearances specified on the product rating plate. The rating plate can be found on the underside of the cooktop.

Proper gas supply connection must be available; refer to Gas Supply Requirements on page 10. Electrical ground is required; see Electrical Requirements on page 11.

This cooktop is intended for indoor use.

Page 6 of the Wolf Multi-Function Cooktop user manual — BEFORE YO U S TA RT
Page 6 · cliquer pour agrandir
Page 6

INSTALLATION I N S T R U C T I O N S

SITE P R E PA R AT I O N

O V E R H E A D C A B I N E T D I M E N S I O N S

C) Minimum spacing between overhead side

cabinets must be greater than or equal to the nominal width of the module(s).

D) Minimum 457 mm vertical distance from

Wolf Multi-Function Cooktop — BEFORE YO U S TA RT diagram (page 6)
Fig. 3

the countertop to the bottom of side cabinets within minimum side clearance.

To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a ventilation hood that projects horizontally a minimum of 127 mm beyond the bottom cabinets.

E) Minimum vertical distance between the

countertop and combustible materials above the cooktop module must be 762 mm.

F) Minimum 64 mm from rear wall.

G) Maximum 330 mm depth of overhead and

side cabinets directly above and within side clearance.

L O C AT I O N I N C O U N T E RTO P

Wolf Multi-Function Cooktop — BEFORE YO U S TA RT diagram (page 6)
Fig. 4

A) Minimum flat countertop surface. Must be

Failure to locate the cooktop module without the proper clearances will result in a fire hazard.

equal to or greater than the width of the module(s).

B) Minimum 178 mm wide clearance from the

module side edge to any combustible surface up to 457 mm above the countertop (noted by shaded area).

Wolf Multi-Function Cooktop — BEFORE YO U S TA RT diagram (page 6)
Fig. 5

Minimum installation clearances

Page 7 of the Wolf Multi-Function Cooktop user manual — BEFORE YO U S TA RT
Page 7 · cliquer pour agrandir
Page 7

INSTALLATION S P E C I F I C AT I O N S

M O D E L I C B I M 1 5 / S D I M E N S I O N S

The illustrations below provide the overall dimensions, installation specifications and countertop cut-out for Model ICBIM15/S.

Overall Width 381 mm

Overall Height 127 mm

If the cooktop is not installed above an oven, the gas service may be supplied through the floor. When an oven is installed below the cooktop, unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in the base cabinet to the right of the oven. Refer to the Installation Specifications illustration below for specifics on placement of the electrical and gas supply.

Overall Depth 533 mm

Minimum Cabinet Depth 578 mm

Minimum Height Clearance* 127 mm

Cut-Out Width 356 mm

Cut-Out Depth 489 mm

*A minimum height clearance of 140 mm is required between countertop and any combustible surface directly below the cooktop.

Unit dimensions may vary to ±3 mm.

Wolf Multi-Function Cooktop — BEFORE YO U S TA RT diagram (page 7)
Fig. 6
Wolf Multi-Function Cooktop — BEFORE YO U S TA RT diagram (page 7)
Fig. 7

LOCATION OF GAS SUPPLY MAY ALSO EXTEND 127 mm ON

NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 838 mm recommended cabinet width. 457 mm recommended cabinet width for installation of single 381 mm cooktop or module. *Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop.

356 mm COOKTOP CUT-OUT

Installation Specifications and Countertop Cut-Out Dimensions

Wolf Multi-Function Cooktop — BEFORE YO U S TA RT diagram (page 7)
Fig. 8

Model ICBIM15/S · Overall Dimensions

Page 8 of the Wolf Multi-Function Cooktop user manual — WIDTH
Page 8 · cliquer pour agrandir
Page 8

INSTALLATION I N S T R U C T I O N S

INSTALLATION O P T I O N S

M U LT I P L E C O O K TO P I N S TA L L AT I O N

When two or more modules are installed together, an integrated module filler strip (IFILLER/S) is recommended. Contact your Wolf dealer for information on these accessory components.

If the multi-function cooktop is to be used with any combination of additional cooktop units or modules with a filler strip, the cut-out width is calculated by adding the corresponding units' cut-out dimensions plus 32 mm for each addi- tional unit. Refer to the illustration below.

A C C E S S O R I E S

Optional acces- sories are available through your Wolf dealer.

1518 mm – FOUR MODULES WIDTH OR 1511 mm – 762 mm COOKTOP AND TWO MODULES OR 1276 mm – 914 mm COOKTOP AND ONE MODULE

1130 mm – THREE MODULES WIDTH OR 1124 mm – 762 mm COOKTOP AND ONE MODULE

743 mm TWO MODULES WIDTH

WIDTH

DEPTH

FRONT OF COUNTERTOP

Countertop cut-out dimensions for installation of multiple cooktops and/or modules

356 mm CUT-OUT · 489 mm CUT-OUT · 64 mm min

Page 9 of the Wolf Multi-Function Cooktop user manual — GAS R AT I N G
Page 9 · cliquer pour agrandir
Page 9

GAS SUPPLY R E Q U I R E M E N T S

The product rating plate, located on the under- side of the cooktop, has information on the type of gas that should be used. If this infor- mation does not agree with the type of gas available, contact your Wolf dealer. To obtain local dealer information, visit the Locator section of our website, wolfappliance.com.

EXPLOSION HAZARD—

Securely tighten all gas connections.

I M P O RTA N T N OT E

Failure to do so can result in explosion, fire or death.

An ISO 7-1 gas inlet thread is provided on all units. Please contact your local Wolf dealer if an ISO 228-1 or other gas inlet thread is required. Pipe joint compounds suitable for use with LP gas should be used. LP gas suppliers usually determine the size and materials used on the system.

This installation must conform with local codes and ordinances.

If rigid pipe is used as a gas supply line, a combination of pipe fittings must be used to obtain an in-line connection to the cooktop. All strains must be removed from the supply and gas lines so the cooktop will be level and in line.

GAS R AT I N G

Total Heat Electrical Types and Output Gas Rating Gas Pressures Model # (Gas) Units (Amps) Category (mbar) Country of Destination

AT, DK, EE, FI, GR, IE, IT, I2H G20 at 20 LT, NO, PT, ES, SE, SI, SK,

ICBIM15/S 8.0 kW 0.17 GB & CH

I2E G20 at 20 DE & PL

I2E+ G20 at 20/25 BE & FR

ICBIM15/S-LP 581 g/h 0.17 I3P G31 at 37 BE, CZ, FR, GR, IE, NL, NO, PT, ES, GB & CH

Page 10 of the Wolf Multi-Function Cooktop user manual — ELECTRICAL SHOCK HAZARD—
Page 10 · cliquer pour agrandir
Page 10

INSTALLATION I N S T R U C T I O N S

ELECTRICAL R E Q U I R E M E N T S

Electronic ignition systems operate within wide voltage limits, but proper ground and polarity are necessary. In addition to checking that the electrical outlet provides 220-240 V AC power and is correctly grounded, the outlet must be checked by a qualified electrician to see if it is wired with correct polarity.

ELECTRICAL SHOCK HAZARD—

Plug into a grounded 3-prong electrical outlet.

Do not remove ground prong.

Do not use an adapter.

A wiring diagram covering the control circuit for the Wolf multi-function cooktop model can be found on page 15.

Failure to follow these instructions can result in electric shock, fire or death.

If an electrical outlet is not available, it is the obligation of the customer to have a properly grounded, 3-prong electrical outlet installed by a qualified electrician.

A 220-240 V AC, 50/60 Hz, 15 amp electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this appli- ance be provided.

Page 11 of the Wolf Multi-Function Cooktop user manual — C O O K TO P INSTALLATION
Page 11 · cliquer pour agrandir
Page 11

C O O K TO P INSTALLATION

G A S S U P P LY L I N E C O N N E C T I O N

Insert the cooktop into the countertop cut-out opening. Center the cooktop in the opening and make sure that the front edge of cooktop is parallel to the front edge of the countertop. Check that all required clearances are met. Use a pencil to outline the rear edge of the cooktop on the countertop. Remove the cooktop from the countertop opening.

Assemble the flexible metal connector from the gas supply pipe to the gas entrance nipple. You will need to determine the fittings required, depending on the size of your gas supply line and flexible metal connector.

Use a pipe-joint compound made for use with natural and LP gas. If a flexible metal connec- tor is used, be sure the tubing is not kinked.

Remove the foam strip from the hardware package. Apply the foam strip around the bottom of the burner box flush with the edge as shown in the illustration below.

Reinsert the cooktop into the countertop opening. Check that the cooktop is parallel to the front edge of the countertop. Lift the entire cooktop to make adjustments and align the rear edge with the pencil line.

Attach the brackets to the burner box by insert- ing the clips into the rectangular punchouts on the left and right side of the burner box. Insert the 89 mm clamping screws into the brackets. Use a screwdriver to tighten the clamping screws against the underside of the counter- top. Refer to the illustration below. Do not overtighten screws.

Show 11 more labels / short text on this page
Countertop · Burner Box · Cooktop Burner Box · Foam · Strip · Bracket · 89 mm Clamping · Clip · Screw · Foam strip application · Bracket installation
Page 12 of the Wolf Multi-Function Cooktop user manual — C O O K TO P INSTALLATION
Page 12 · cliquer pour agrandir
Page 12

INSTALLATION I N S T R U C T I O N S

C O O K TO P INSTALLATION

SURFACE B U R N E R S

G A S L E A K T E S T I N G

I N I T I A L L I G H T I N G

Use a brush and liquid detergent to test all gas connections for leaks. Bubbles around connec- tions will indicate a leak. If a leak appears, shut off gas valve controls and adjust connections. Then check connections again. Clean all the detergent solution from the cooktop.

The cooktop burner uses an electronic igniter in place of a standing pilot. When the cooktop control knob is pushed in and turned to the

position, the system creates a spark to light the burner. This sparking continues for 4 seconds or until the electronic ignition senses a flame, which ever comes first. If the igniter fails to ignite the gas in 4 seconds, the gas safety shutoff valve will close, eliminating the gas flow for 5 seconds. The valve will reopen after the purge time of 5 seconds, and the igniter will automatically attempt to re-ignite the gas. This cycle of events is attempted 3 times. After the third attempt, in order for gas to flow to the burner once again, the user must return the knob to the position and then turn the knob to the position.

Never test for a gas leak with a match or other flame.

C O M P L E T I N G T H E I N S TA L L AT I O N

Once the cooktop has been checked for any gas leaks, plug the power supply cord into the grounded electrical outlet.

To check operation of the cooktop burner, push in and turn the control knob to the position. The flame should light within four seconds.

Place the burner head on the burner base and position the burner grate over the burner assembly.

If the burner does not light properly, turn the control knob to the position. Check that the burner head is in the proper position. Check that the power supply cord is plugged in and that the circuit breaker or house fuse has not blown. Check operation again; if the burner does not light properly at this point, contact your Wolf dealer or regional distributor.

Page 13 of the Wolf Multi-Function Cooktop user manual — TROUBLE S H O OT I N G
Page 13 · cliquer pour agrandir
Page 13

COOKTOP R E M O VA L

I F YO U N E E D SERVICE

If it is necessary to remove the multi-function cooktop for cleaning or service, shut off the gas supply. Disconnect the gas and electric supply. Remove the mounting brackets on the right and left side of the burner box and remove the cooktop. Reinstall in the reverse order and check the gas connection for leaks.

For service in your area, contact either your Wolf dealer or visit the Locator section of our website, wolfappliance.com to find the regional distributor by country.

C O N TA C T I N F O R M AT I O N

When calling for service, you will need the model and serial number of your multi- function cooktop. Both numbers are listed on the rating plate, located on the under- side of the cooktop. Refer to the illustration on page 5.

TROUBLE S H O OT I N G

Websitewolfappliance.com

Verify that power is being supplied to the cooktop.

Check the gas supply and electrical connections to ensure that the installation has been completed correctly.

Refer to the Troubleshooting Guide in the Wolf Multi-Function Cooktop Use & Care Information.

If the cooktop still does not work, contact your Wolf dealer or regional distributor. Do not attempt to repair the cooktop yourself.

Page 14 of the Wolf Multi-Function Cooktop user manual — WIRING D I A G R A M
Page 14 · cliquer pour agrandir
Page 14

INSTALLATION I N S T R U C T I O N S

WIRING D I A G R A M

Wolf Multi-Function Cooktop — WIRING D I A G R A M diagram (page 14)
Fig. 9

The information and images in this book are the copyright property of Wolf Appliance, Inc., an affiliate of Sub-Zero, Inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Wolf Appliance, Inc., an affiliate of Sub-Zero, Inc.

©Wolf Appliance, Inc. all rights reserved.

Sources

Références et liens

Pages mentionnées dans ce manuel — fabricant, assistance et téléchargements.

Poser une question sur : Wolf Multi-Function Cooktop

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Wolf Multi-Function Cooktop

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Wolf Multi-Function Cooktop manuel PDF

63 pages·776 KB·Table de cuisson·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…