Manuel d'utilisation / d'entretien du produit WESY86303 du fabricant Weider
Aller à la page of 36
USER'S MANUAL QUESTIONS? As a manufacturer , we are committed to providing complete customer satisfaction. If you have questions, or if there are missing or damaged parts, we will guarantee complete satisfac- tion through direct assistance from our factory .
2 T ABLE OF CONTENTS LIMITED W ARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .
3 IMPORT ANT PRECAUTIONS W ARNING: T o reduce the risk of serious injury , read the following important precautions before using the training system. 1. It is the responsibility of the owner to ensure that all users of the training system are ade- quately informed of all precautions.
4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 78 in. W idth: 64 in. Length: 70 in. Foot Plate Low Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arms Press Arm Weight Stacks Backrests Leg Press Plate Ab Pulley Station W ARNING DECAL W ARNING DECAL Thank you for selecting the versatile WEIDER ® 8630 t raining system.
5 ASSEMBL Y Make sure you have the following tools: • T wo (2) adjustable wrenches • One (1) standard screwdriver • One (1) phillips screwdriver • One (1) rubber mallet • Y ou will also need grease or petroleum jelly , a small amount of soapy water , and clear tape or masking tape.
1. Locate and open the parts bags labeled “FRAME ASSEMBL Y BAG ONE” and “FRAME ASSEMBL Y BAG TWO.” Press two 2” Square Outer Caps (58) onto the Weight Base (14) in the indicated locations. Press a 2” Square Inner Cap (56) into the end of the Weight Base.
4. Slide the Front Seat Frame (8) onto the indi- cated 5/16” x 2 1/2” Carriage Bolts (49) in the P ress Base (13). Hand tighten two 5/16” Nylon Locknuts (40) onto the Carriage Bolts.
8. Lubricate the insides of the holes in the T op Weights (24) as shown. Slide a T op Weight o nto each set of Weight Guides (23). 9. Attach the T op Frame (2) to the Ab Upright (1) with two 5/16” x 2 3/4” Bolts (55), two 5/16” W ashers (20), and two 5/16” Nylon Locknuts (40).
1 1. Attach the Leg Press Plate (1 1) to the Adjustment T ube (10) with a 5/16” x 2 1/2” B olt (39), two 5/16” W ashers (20), and a 5/16” Nylon Locknut (40). Be sure that the Leg P ress Plate and Adjustment T ube are ori- ented as shown. Press a 1 3/4” Square Inner Cap (48) into the Adjustment T ube (10).
10 15. Attach a Press Arm (7) to one side of the Press Frame (12) with two 5/16” x 2 1/2” Bolts ( 39) and two 5/16” Nylon Locknuts (40). A ttach the other Press Arm (7) to the Press Frame (12) in the same manner . 16. Press a 1” Round Inner Cap (70) into one of the Press Arms (7).
1 1 18. Press a 1 3/4” Square Inner Cap (48) into the lower end of the Left Fly Arm (6). Wet the l ower end of the Left Fly Arm with soapy water . Slide a 10” Pad (22) onto the Left Arm. Repeat this step with the Right Fly Arm (5). 19. Locate and open the parts bags labeled “CABLE ASSEMBL Y” and “PULLEYS.
12 21. Wrap the Butterfly Cable (89) around a 3 1/2” Pulley (82) as shown. Attach the Pulley and a C able T rap (80) to the bracket on the Leg Press Upright (4) with a 3/8” x 2” Bolt (50) a nd a 3/8” Nylon Locknut (42). T he Cable T rap must be oriented as shown and be positioned to hold the Cable in the groove of the Pulley .
13 25. Identify the Rear Cable (87)—this is the shortest Cable. Slide one end of the Rear C able onto the 5/16” x 3” Bolt (92). Thread another 5/16” Nylon Jam Nut (91) onto the B olt, b ut do not fully tighten it. Leave enough room between the two Jam Nuts for the Cable to pivot.
14 29. Identify the Press Cable (88)—this is the longest Cable. Attach the end of the Press C able (88) to the Large “U” Bracket (84) with a 1/4” Nylon Locknut (44) and a 1/4” W asher ( 37).
15 32. Route the Press Cable (88) over the indicated 3 1/2” Pulley (82) attached to the Pulley P lates (31). T he Cable must be routed from the direction shown. Refer to the inset draw- i ng. B e sure that the Cable is between the Cable T rap (80) and the Pulley , and that the Cable T rap is positioned to hold the Cable in place.
16 36. Route the Press Cable (88) over the indicated 3 1/2” Pulley (82) attached to the Press F rame (12). B e sure that the Cable T rap (80) is turned to hold the Cable in place a nd that the Cable is between the Pulley and the crossbar on the Press Frame.
17 40. Note: The 3 1/2” Pulley (82) used in this step was attached in step 38. It is shown r emoved for easier part identification. R oute the Press Cable (88) around the 3 1/2” Pulley (82). Be sure that the Cable T rap (80) is turned to hold the Cable in place and that the Cable is routed as shown.
18 44. Locate the remaining preassembled pair of Pulley Plates (31) and 3 1/2” Pulleys (82). Route the High Cable (85) under the indicated 3 1/2” Pulley (82). The end of the Pulley Plates (31) with two holes should be down- ward. Refer to the inset drawing.
19 48. Wrap the Low Cable (86) around a 3 1/2” Pulley (82). Attach the Pulley and a Cable T rap (80) to the Ab Upright (1) with the 3/8” x 3 3/4” Bolt (76) and a 3/8” Nylon Locknut (42). B e sure that the Cable T rap is in the indi- cated position.
51. Locate and open the parts bag labeled “SEA T ASSEMBL Y .” Attach the Small Backrest (18) to the Ab U pright (1) with two 1/4” x 2 1/2” Machine Screws (64) and two 1/4” W ashers (37). 52. Press a 1 1/2” Square Inner Cap (57) into the Rear Seat Frame (16).
55 56 57 SEA T ASSEMBL Y MISC. 21 58. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in HOW T O USE THE TRAINING SYSTEM, beginning on page 22 of this manual. Before using the training system, pull each cable a few times to be sure that the cables move smoothly over the pulleys.
22 HOW T O USE THE TRAINING SYSTEM T he instructions below describe how each part of the training system can be adjusted. Refer to the exercise poster accompanying this manual to see how the training system should be set up for each exercise.
23 A TT ACHING THE AB STRAP TO THE AB PULLEY ST A TION Attach the Ab Strap (35) to the Low Cable (86) at the a b pulley station with a Cable Clip (33). A TT ACHING AND REMOVING THE SEA T T o attach the Seat (17), set the bracket on the Rear Seat Frame (16) onto the pins on the Ab Upright (1).
24 WEIGHT RESIST ANCE CHART This chart shows the approximate weight resistance at each weight station. “T op” refers to the 6.5 lb. top weight. The other numbers refer to the 12.5 lb. weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm.
TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the training system. Replace any worn parts immediately . The t raining system can be cleaned using a damp cloth and mild non-abrasive detergent.
26 CABLE DIAGRAMS The cable diagrams on this page and the next page show the proper routing of the High Cable (85), the Low Cable (86), the Rear Cable (87), the Press Cable (88), and the Butterfly Cable (89). Use the diagrams to be sure that the Cables have been assembled correctly .
27 High Cable (85) Rear Cable (87) Weight Stack— 5 High Pulley— 1 2 2 3 3 1 —T op Frame 4 —Weight Stack 4.
1/2" x 3/4" Abstandsstück (69) 2" Quadratische Innenkappe (56) 2" Quadratische Außenkappe(58) 1 3/4" Quadratische Innenkappe (48) 1" Runde Außenkappe (46) 1 1/2" .
3/8" Nylonkontermutter (43) 5/16" x 1 3/4" Bolzen (68) 3/8" x 2" Bolzen (50) 5/16" x 2 1/4" Bolzen (62) 5/16" x 2 1/2" Bolzen (39) 3/8" x 2 1/2" .
5/16" x 2" Augenbolzen (79) Kabelklammer (33) 3/8" x 5" Bolzen (74) 3/8" x 3 3/4" Bolzen (76) 5/16" x 2 3/4" Schraubenbolzen (77) 5/16" x 2 1/2" Schra.
P ART LIST—Model No. WESY86303 R0100A Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty .
This chart is provided to help you identify the small parts used in assembly . Im po rta nt : Some parts m ay ha ve b ee n pre-assembled for shipping purposes; if you cannot find a part in the parts bags, check to see if it ha s bee n pre-assembled.
REMOVE THIS P AR T LIST/EXPLODED DRA WING FROM THE MANUAL! 81 REMOVE THIS P ART LIST/EXPLODED DRA WING FROM THE MANUAL. SA VE THE P ART LIST/EXPLODED DRA WING FOR FUTURE REFERENCE.
1 2 3 4 5 6 7 7 8 9 10 1 1 12 13 14 15 16 17 18 19 17 21 21 22 22 23 23 24 24 25 25 26 26 27 27 28 28 29 29 29 29 30 31 32 32 33 34 35 36 21 21 85 85 87 86 31 41 41 86 87 88 88 89 89 56 76 82 38 42 20.
3 4 5 6 7 12 13 14 1 19 1 21 22 22 23 23 24 24 25 25 26 26 27 27 31 32 32 33 34 35 36 21 21 8 85 87 8 31 4 86 8 7 88 8 89 8 9 5 50 3 2 0 56 82 80 43 42 50 40 69 4 0 6 9 6 7 67 40 68 37 44 40 37 68 44 .
ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- p ared to give the following information: 1.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Weider WESY86303 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Weider WESY86303 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Weider WESY86303, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Weider WESY86303 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Weider WESY86303, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Weider WESY86303.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Weider WESY86303. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Weider WESY86303 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
