Manuel d'utilisation / d'entretien du produit 178704 du fabricant Weed Eater
Aller à la page of 44
OWNER'S MANUAL MODEL NO . S165H42C 16.5 HP 42 Inch La wn T ractor For Parts and Service, contact our authorized distributor: call 1-800-849-1297 For T echnical Assistance: call 1-800-829-5886 178704 Re v .
2 Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
3 • Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. • Never carry passengers or children even with the blades off. • Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing.
4 PRODUCT SPECIFICA TIONS GASOLINE CAPACITY 2.0 GALLONS AND TYPE: UNLEADED REGULAR OIL TYPE (API-SF-SJ): SAE 30 (above 32 ° F) SAE 5W-30 (below 32 ° F) OIL CAPACITY: 3.4 PINTS SPARK PLUG: CHAMPION RN4C (GAP: .030") GROUND SPEED (MPH): FORWARD: 5.
5 UNASSEMBLED P AR TS Steering Wheel Steering Wheel Insert (1) Large Flat Washer (1) Locknut 5/16-18 (1) Hex Bolt 5/16-18 x 1-1/4 (1) Hex Bolt 3/8-16 x 1 (1) Lockwasher 3/8 Steering Boot Steering Exte.
6 ASSEMBL Y T OOLS REQUIRED FOR ASSEMBL Y A socket wrench set will make assembly easier. Standard wrench sizes are listed. (1) 9/16" wrench Pliers (2) 1/2" wrenches Tire pressure gauge Utility knife When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).
7 ASSEMBL Y TO ROLL TRACTOR OFF SKID (See Operation section, for location and function of controls) • Press lift lever plunger and raise attachment lift lever to its highest position.
8 CHECKLIST BEFORE YOU OPERATE AND ENJOY YOUR NEW TRAC- TOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST: All assembly instructions have been completed. No remaining loose parts in carton.
9 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. BATTERY CAUTION OR WARNING REVERSE FORWARD FAST SLOW ENGINE ON ENG.
10 OPERA TION KNO W Y OUR TRA CT OR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
11 OPERA TION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.
12 OPERA TION TO OPERATE ON HILLS CAUTION: Do not drive up or down hills with slopes greater than 15 ° and do not drive across any slope. • Choose the slowest speed before starting up or down hills. • Avoid stopping or changing speed on hills. • If slowing is necessary, move throttle control lever to slower position.
13 PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is run- ning. To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time.
14 FIG. 9 MO WING TIPS • Mower should be properly leveled for best mowing performance. See “ TO LEVEL MOWER HOUSING ” in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trimming. • Drive so that clippings are discharged onto the area that has been cut.
15 CUST OMER RESPONSIBILITIES BEFORE EACH USE T R A C T 0 R Adjust Motion Drive Belt(s) Tension Inspect Muffler/Spark Arrester Lubrication Chart Check Brake Operation Clean Air Filter Change Engine Oi.
16 CUST OMER RESPONSIBILITIES BLADE REMOVAL (See Fig. 10) • Raise mower to highest position to allow access to blades. • Remove hex bolt, lock washer and flat washer securing blade. • Install new or resharpened blade with trailing edge up towards deck as shown.
17 CUST OMER RESPONSIBILITIES V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling.
18 CUST OMER RESPONSIBILITIES MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. SPARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first.
19 SER VICE AND ADJUSTMENTS FIG. 16 CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress clutch/brake pedal fully and set parking brake. • Place motion control lever in neutral (N) position. • Place attachment clutch in “ DISENGAGED ” position.
20 TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 21) The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake. BELT REMOVAL - • Remove mower from tractor (See “ TO REMOVE MOWER ” in this section of this manual).
21 SER VICE AND ADJUSTMENTS FIG. 23 ENGINE PULLEY CLUTCHING IDLER STATIONARY IDLER TRANSMISSION INPUT PULLEY WITH PARKING BRAKE “ ENGAGED ” JAM NUT OPERATING ARM NUT “ A ” FIG. 22 TO REPLACE MOTION DRIVE BELT (See Fig. 23) Park the tractor on level surface.
22 FIG. 26 POSITIVE TERMINAL CHASSIS POSITIVE TERMINAL CHARGED BATTERY CABLES NEGATIVE TERMINAL NEGATIVE TERMINAL REPLACING BATTERY (See Figs. 27 and 28) CAUTION: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time.
23 SER VICE AND ADJUSTMENTS FIG. 28 KEPS NUT HEX BOLT POSITIVE (RED) CABLE NEGATIVE (BLACK) CABLE TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 29) • Raise hood. • Unsnap headlight wire connector. • Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.
24 ST ORA GE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
25 TR OUBLESHOO TING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “ CHOKED ” properly. 2. See “ TO START ENGINE ” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug.
26 TR OUBLESHOO TING POINTS PROBLEM CAUSE CORRECTION Engine continues to run 1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not when operator leaves corrected, contact an authorized service center/ seat with attachment department.
27 TRA CT OR - - MODEL NUMBER S165H42C SCHEMA TIC BATTERY FUSE IGNITION SWITCH RED RED RED BLACK IGNITION UNIT HEADLIGHTS REMOVABLE CONNECTIONS BLACK BLACK BLACK WHITE WHITE WHITE RED BLACK ORANGE BLA.
28 28 29 26 24 42 43 27 27 25 41 27 27 40 33 30 8 2 1 27 16 16 52 D .C . A M P E R E S 45 22 21 REP AIR P AR TS TRA CT OR - - MODEL NUMBER S165H42C ELECTRICAL 81 81 81.
29 REP AIR P ARTS TRA CT OR - - MODEL NUMBER S165H42C ELECTRICAL 1 144925 Battery 12 Volt 25 Amp 2 74760412 Bo l t Hex Hd 1/4-20unc X 3/4 8 156417 Case Battery 1 6 153664 Switch Interlock Push -In 2 1.
30 REP AIR P AR TS TRA CT OR - - MODEL NUMBER S165H42C CHASSIS AND ENCLOSURES 37 37 3 2 35 3 26 3 35 26 33 10 34 1 208 11 17 29 28 208 13 207 20 207 23 12 51 57 53 52 54 55 24 26 25 26 25 3 31 24 30 2.
31 REP AIR P AR TS TRA CT OR - - MODEL NUMBER S165H42C CHASSIS AND ENCLOSURES 1 174620 Chassis 2 176554 Drawbar 3 17060612 Screw 3/8-16 x 3/4 5 155272 Bumper Hood/Dash 6 155923 Saddle Flat Lt Fender Shift 8 155138 Clip Retainer Slide-On 9 168348X012 Dash 1 0 72140608 Bolt RdHd Sqnk.
32 REP AIR P AR TS TRA CT OR - - MODEL NUMBER S165H42C DRIVE 51 59 81 38 61 41 42 40 42 39 89 69 56 64 65 212 63 116 70 57 66 27 51 48 151 202 49 47 50 120 150 156 166 165 82 168 163 14 164 21 8 10 83.
33 REP AIR P AR TS TRA CT OR - - MODEL NUMBER S165H42C DRIVE KEY P ART N O . NO . DESCRIPTION KEY P ART N O . NO . DESCRIPTION NO TE: All component dimensions given in U .
34 REP AIR P AR TS TRA CT OR - - MODEL NUMBER S165H42C STEERING ASSEMBL Y 44 51 54 5 9 5 7 7 9 4 3 32 43 6 43 8 10 40 11 8 6 9 46 46 8 6 9 2 47 47 26 30 28 1 41 42 37 36 37 38 63 11 39 68 67 67 67 13 .
35 REP AIR P AR TS TRA CT OR - - MODEL NUMBER S165H42C STEERING ASSEMBL Y 1 133741X428 Wheel Steering 2 154427 Axle Asm Front 3 169840 Spindle Asm Lh 4 169839 Spindle Asm Rh 5 6266H Bearing Race Thrus.
36 NO TE: All component dimensions given in U .S . inches 1 inch = 25.4 mm KEY P ART N O . NO . DESCRIPTION 1 170551 Control Throt/Ch 2 17720410 Screw Hex Thd Cut 1/4-20x5/8 T 3 - - - - - - Engine Tec, Model OHV165 (Order parts from engine manufacturer) 4 137351 Muffler Tec 13.
37 1 159460 Wire Asm Inner/Sprg w/Plunger 2 159471 Shaft Asm Lift 3 105767X Pin Groove 4 12000002 E Ring #5133-62 5 19211621 Washer 21/32 x 1 x 21 Ga. 6 120183X Bearing Nylon 7 109413X Grip Handle 8 124526X Button Plunger 1 1 139865 Link Lift Lh 1 2 139866 Link Lift Rh 1 3 4939M Re t a i ner Spring KEY P ART N O .
38 REP AIR P AR TS TRA CT OR - - MODEL NUMBER S165H42C SEA T ASSEMBL Y KEY P ART N O . NO . DESCRIPTION KEY P ART N O . NO . DESCRIPTION 1 4 72050412 Bolt Rdhd Sht Nk 1/4-20 x 1-1/2 1 5 134300 Spacer .
39 20 2 3 9 7 4 10 7 11 14 WHEELS & TIRES KEY P ART N O . NO . DESCRIPTION 1 59192 Cap Valve Tire 2 65139 Stem Valve 3 106222X Tire F Ts 15 X 6 0 - 6 Service 4 59904 Tube Front (Service Item Only).
40 REP AIR P AR TS TRA CT OR - - MODEL NUMBER S165H42C MO WER DECK 15 14 13 11 10 9 8 16 68 37 30 31 32 33 146 148 145 150 45 144 147 147 142 149 142 49 50 51 54 52 53 55 56 34 1 46 44 21 22 24 25 26 .
41 REP AIR P AR TS TRA CT OR - - MODEL NUMBER S165H42C MO WER DECK 1 165892 Mower Deck Assembly, 42" 2 72140506 Bolt 3 138017 Bracket Asm Fr. Sway Bar 3/42 4 165460 Bracket Asm Deck 42" Sway.
42 LIMITED WARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and workmanship.
43 15 MAX. SIGHT AND HOLD THIS LEVEL WITH SKY LINE OR TREE. CUT OUT ON DOTTED LINES THIS IS A 15 SLOPE SIGHTING GUIDE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION Operate your Tractor up and down the face of slopes (not greater than 15 ), never across the face.
®.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Weed Eater 178704 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Weed Eater 178704 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Weed Eater 178704, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Weed Eater 178704 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Weed Eater 178704, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Weed Eater 178704.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Weed Eater 178704. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Weed Eater 178704 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
