Manuel d'utilisation / d'entretien du produit 9100/9400/9600 du fabricant Wayne-Dalton
Aller à la page of 18
GARAGE DOORS & OPENERS Part No. IMPORT ANT NO TICES! Wayne-Dalton highly recommends that you read and fully under - stand the Installation Instructions and Owner’ s Manual before you attempt this installation. T o avoid possible injur y , read the enclosed instructions carefully before installing and operating the garage door .
2 Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com A.
I m p o r t a n t S a f e t y I n s t r u c t i o n s Definition of key words used in this manual: W ARNING W ARNING INDICA TES A POTENTIALL Y HAZARDOUS SITUA TION WHICH; IF NOT AVOIDED , COULD RESUL T IN SEVERE OR FA T AL INJURY . CAUTION: PROPER TY DAMAGE OR INJURY CAN RESUL T FROM FAILURE TO FOLLOW INSTRUCTIONS.
5/16” x 1 5/8” Hex head lag screws (as required) 1/4”-20 x 11/16” Self drilling screws (as required) 1/4”-14 x 5/8” Self tapping screws (as required) (2) #12 x 1/2” Phillips head screws .
and flush with the inside edge of the jamb. T emporarily secure the weatherstrip with equally spaced nails. Repeat for other side. This will keep the bottom section from falling out of the opening during installation. Equally space nails approximately 12” to 18” apart.
INST ALLA TION Before installing your door , be certain that you have read and followed all of the instruc- tions covered in the pre-installation section of this manual. Failure to do so may result in an improperly installed door . NOTE: Reference TDS 160 for general garage door terminology at www.
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com section until it is seated against bottom section.
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com T op Section T ools: Hammer , Step ladder , T ape measure 14 Place the top section in the opening.
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.
Door Arm Hookup T ools: Needle nose pliers Align hole in the door arm with holes in drawbar operator bracket tabs, as shown. Insert 5/16” x 1-1/4” clevis pin, making sure hole in clevis pin is outside of second tab of drawbar operator bracket. Insert hairpin cotter into clevis pin hole and spread hairpin cotter to secure assembly , as shown.
Second section 1/8” Inside lock End cap (4) 1/4”-20 x 11/16” Self drilling screws Square hole in vertical track Pull Down Rope T ools: Power drill, 1/8” Drill bit, T ape measure W ARNING W ARNING DO NOT INST ALL PULL DOWN ROPE ON DOORS WITH OPERA TORS.
Cleaning Y our Garage Door IMPORT ANT : DO NOT USE A PRESSURE W ASHER ON YOUR GARAGE DOOR! While factory-applied finishes on garage doors are durable, it is desirable to clean them on a routine basis. Some discoloration of the finish may occur when a door has been exposed to dirt-laden atmosphere for a period of time.
Lifetime Limited Warranty Models 9100, 9400, 9600 Subject to the terms and conditions contained in this Lifetime Limited Warranty , Wayne-Dalton, A Division Of Overhead Door Corporation (“Manufactur.
.
AFTER INST ALLA TION IS COMPLETE, F ASTEN THIS MANUAL NEAR THE GARAGE DOOR. Please Do Not Return This Product T o The Store Thank you for your pur chase. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pa ges business listings or go to the Find a Dealer section online at www .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Wayne-Dalton 9100/9400/9600 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Wayne-Dalton 9100/9400/9600 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Wayne-Dalton 9100/9400/9600, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Wayne-Dalton 9100/9400/9600 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Wayne-Dalton 9100/9400/9600, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Wayne-Dalton 9100/9400/9600.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Wayne-Dalton 9100/9400/9600. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Wayne-Dalton 9100/9400/9600 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
