Manuel d'utilisation / d'entretien du produit VT 1900 du fabricant VTech
Aller à la page of 17
@za VTECH COMMUNICATIONS LTD. Is a trademark of VTECH COMMUNICATIONS LTD.., a member of THE VTECH GROUP OF COMPANIES. Distributed in the U.S.A. by VTECH Communications, 8770 SW Nimbus Avenue / Beaverton, Oregon, 97008. Distributed in Canada by VTECH Electronics Canada Ltd.
Page INTRODUCTION ............................................................................................................. 1 SPECIAL FEATURES ...................................................................................................... 2 PARTS CHECK LIST .
Congratulations! You have purchased one of the most sophisticated cordless telephones on the market! The VTech VT1900 has been designed to offer a new standard in cordless telephone technology.
Parts Check List To purchase replacement battery 1. Base unit, Handset and AC adapter packs, call VTECH Communications at 2. One-Line Telephone Cord 1-800-624-5688. In Canada, call HANDSET UNlT CONTROLS AND FUNCTIONS 3. Battery Pack VTECH Electronics at 1-800-267- 4.
This equipment complies with Parts 15 BASE UNIT CONTROLS AND FUNCTIONS and 68ofthe ~ederal Communications Commission (FCC) rules for the United - TONEIPULSE AC POWER JACK PHONE CORD JACK ANTENNA BAlTE.
FCC Part 68 The FCC requires that you connect your cordless telephone to the nationwide telephone network through a modular telephone jack (USOC RJIIC, RJIlW or RJ14). Your telephone company may discontinue your service if your equipment causes harm to the telephone network.
When using your telephone equipment, basic safety precautions shouldalways be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product.
Follow the steps below: 1. Remove the battery case cover by pressing on the ridged lines and slidina downward. PRESS and SLIDE DOWNWARD 2. Discard the old battery pack. Don't put the old battery pack in a trash compactor or a fire - it could burst.
Fill in the telephone number card on the base unit. CARD CHEAK FOR A DIAL TONE. After the batteries are charged, pick up the handset. Now press PHONE on the handset, you should hear dial tone. If not, see 'IN CASE OF DIFFICULTY' on page 26. CAUTION: 1.
USING THE WALL MOUNT ADAPTOR 1. Position the wall mount bracket on the base. Line up the tabs on the wall mount adaptor with the holes on the bottom of the base (Figure 1). Snap the wall mount bracket firmly in place. 2. Mount the base on the wall. Position the base so the mounting studs will fit into the holes on the bottom of the base.
MEMORY STORING The phone should be m. press (PTG) . Enter the two digit memory location (00 .. 20). Enter the number you wish to store, up to a maximum of 20 digits. Press (MEM) to store number and exit program mode. MEMORY STORING -11 1 MEMORY DIALING Enter the memory location of the number you wish to dial (00.
TEMPORARY TONE If you have a rotary (dial-pulse) telephone service, (TONEIPULSE switch is set to PULSE), this feature allows you to enter special codes and tones to operate answering machines, use electronic banking services, calling cards, or other special services.
The VTech VT1900 is capable of memory dialing. You can dial by pressing the memory location in which the number was stored. STORING SPEED DlAL NUMBERS To program a speed dial location, do the following: With the hone @@ mode. Press (&G) . The PHONE LED will flash quickly to indicate that the unit is in program mode.
CHANGING STORED NUMBERS To change or replace a stored number, simply store a new number in the desired memory location following the instructions listed in, STORING SPEED DIAL NUMBERS. See page 21. DELETING STORED NUMBERS To delete a stored number from memory do the following: Press to enter program mode.
If the handset is moved to a point where the base and handset can no longer communicate, the handset will make a quick series of beeps to signal Out of Range. OUT OF RANGE WHEN PHONE IS ON ' If you are presently engaged in a phone conversation move closer to the base.
YOU HEAR OTHER CALLS WHILE USING YOUR PHONE. Disconnect your base unit from the telephone jack, and plug in a regular telephone. If you still hear other calls, the problem is probably in your wiring or local service. Call your local telephone company.
FREQUENCY CONTROL Crystal Controlled Dual PLL Synthesizer TRANSMIT FREQUENCY Handset: 925.05 MHz to 927.75 MHz (All ten channels within this range) Base: 902.3 MHz to 905.0 MHz (All ten channels within this range) RECE~VE FREQUENCY Handset: 902.3 MHz to 905.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté VTech VT 1900 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du VTech VT 1900 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation VTech VT 1900, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le VTech VT 1900 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le VTech VT 1900, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du VTech VT 1900.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le VTech VT 1900. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei VTech VT 1900 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
