Manuel d'utilisation / d'entretien du produit XDECT R055 du fabricant Uniden
Aller à la page of 60
XDECT R055.
.
Headset (HS910) XDECT R055 Series Owner's Manual What's in the box? Base AC adapter (AAD-041S(M)) 2 x Telephone cords Belt clip XDECT R005 accessory handset and repeater with charger If you .
Important Safety Instructions! When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of re, electric shock and injury to persons, including the following: This unit is NOT waterproof. DO NOT expose this unit to rain or moisture.
1 Installing Your Phone Setup the Base Attach the stand Before you attach the stand, you have to decide if you want the phone to rest on a desk or hang on a wall. For desktop use, turn 1. the stand so the locking tabs that say DESK are facing the base with the arrows pointing up.
2 Connect the power and telephone cord(s) Connect the base AC adapter to the 1. DC IN 9V jack and route the cord as shown: For desktop use For wall mount use PRIMARY LINE TEL LINE 2 DC IN 9V PRIMARY LINE TEL LINE 2 DC IN 9V Connect one of the included telephone cords to the 2.
3 Place the main base on the wall Place the mounting slots (hole spacing is 100mm vertical) over the pins on the wall plate, and slide the base down to lock it into place.
4 Setup the Repeater/Charger(s) (if included) Connect the repeater/charger power cord 1. If your phone came with any accessory handsets and chargers, connect a charger AC adapter to each charger's DC IN 9V jack and set the plug into the notch as shown.
5 Setup the Handset(s) Install the battery Unpack all handsets, battery packs, 1. and battery covers. If any handset has the battery cover already attached, press in on the notch and slide the cover down and off. Line up the battery pack connector 2. with the jack inside the handset.
6 If... Try... a CHARGE light doesn't turn on reseating the handset. - checking the AC adapter connection. - Charge all handsets completely (about 15 hours) before using them. When fully charged the battery will provide up to 8hrs talk time and 7 days standby time.
7 Test the Connection Pick up the handset from the base and press TALK/FLASH. . The phone should pick up line 1 automatically and change the display to show Talk , and you should hear a dial tone. When you get a dial tone, make a test call; press END to hang up.
8 Using the Repeater How it works An XDECT R005 repeater can extend the range of your base in all directions, including up and down. The XDECT R005 repeater unit is also a charger for the accessory handset.
9 Repeaters can be up to 3 chain-links (maximum) from the base Example of coverage area with 6 repeaters (maximum total) You can roam anywhere within range of the base or the repeater(s) and make and receive calls as usual from your handsets.
10 Picking the best spot The best spot for the repeater is as far from the base as possible while still maintaining a good signal, or near the edge of the base’s coverage area. To find the edge of the coverage area: Stand near the base 1. and make a call on the handset.
11 Getting to Know Your Phone Parts of the Base If the key name is spelled out on the key itself, it's not labeled in the drawing below. Base keys and how they work Key name (and icon) What it does PHONEBOOK/ LEFT ( / ) In standby or during a call: open the phonebook.
12 Key name (and icon) What it does UP ( ) In standby: increase the ringer volume for line 1 or line 2. - During a speakerphone call or while a message is playing: - increase the speaker volume. In the menu or any list: move the cursor up one line. - CALLER ID/ RIGHT ( / ) In standby or during a call: open the Caller ID list.
13 Parts of the Handset Handset keys and how they work Key name (and icon) What it does UP ( ) In standby: increase the ringer volume for line 1 or line 2. - During a call: increase the call volume. - In the menu or any list: move the cursor up one line.
14 Key name (and icon) What it does CALLER ID/ RIGHT ( ) In standby or during a call: open the Caller ID list. - During text entry: move the cursor to the right. - SPEAKER ( ) Switch a normal call to the speakerphone (and back). - INTERCOM/ HOLD In standby: page another station using the intercom.
15 Reading the Displays On the base On the handset The table below shows the possible icons and what they mean. Since the icons appear based on what you're doing with the phone, you won't ever see all of these icons at the same time. Base Icon Handset Icon What it means or The accompanying information (in use, on hold, etc.
16 Base Icon Handset Icon What it means The ringer is turned off for 1) line 1 only, 2) line 2 onl y, or 3) both. T his station will not ring when a call comes in on the indicated lines. You have a vo ice message waiting (se e "Using Voice Message Notification" on page 39).
17 Using the Soft Keys Soft keys are controlled by the software: they will automatically change their function depending on what you're currently doing: Soft keys with the phone in standby On the.
18 If the description for a soft key is blank, that key doesn't currently have a function. Sometimes, the current function of a soft key can duplicate the function of a regular key.
19 Entering Text on Your Phone When you want to enter text into your phone (for example, a name in the phonebook), use the twelve-key dial pad to enter the letters printed on the number keys. Here's how it works: The phone enters the letters in the order they appear on the key.
20 Using the Menus The menus are des igned to be as easy as possibl e. Some users don't even need the manual once they know how to perform these actions: If you don't press any keys for thirty seconds, the phone times out and exits the menu.
21 Close the menu On the handset, press END ; on the base, press MUTE/ EXIT . (If you open the menu during a call, press BACK to back out of the menu without hanging up.
22 Menu option: Use it to: Autotalk (Handset on ly) Turn on Auto T alk so you can ans wer the phone just by picking up the handset from the cradle (without having to press any buttons). Any Key Answer (Handset only) Turn on Any Key Answer so you can answer the phone by pressing a key on the twelve-key dial pad.
23 When you select the Global Setup menu, the phone prompts you to select Line 1 or Line 2 . Then, you can choose one of the following options to change the global settings for that line: Menu option: Use it to: Set Line Mode Do not ch ange this settin g unless instruc ted to by custo mer service.
24 Using Your Phone Working with Two Lines When performing common tasks, you can let the station use the primary line, or you can manually choose a particular line for each task. Using the primary line makes common tasks much simpler, but you will need to assign a primary line to each station (see below).
25 primary line assignment by manually choosing line for your current task. To assign a primary line, open the menu and select Handset Setup or Base Setup . Select Primary Line , then choose the line you want this station to connect to when it goes off hook: Line 1 Always connect to line 1, regardless of either line's status.
26 Changing the Volume You can set the volume of the ringer and speaker separately for the base and each handset; you can also set the earpiece volume on each handset. The available volume levels and how to change them are listed below; for each item, press UP to make it louder or DOWN to make it softer.
27 Using the lists Open the CID list Press CALLER ID/RIGHT . Open the redial list Press REDIAL/PAUSE . Scroll through the CID or redial list Press DOWN to scroll through the lis t from newest to oldest. Press UP to scroll from oldest to newest. Close the CID or redial list Press END on a handset or MUTE/EXIT on the base.
28 Delete All Erase all entries from this station's CID or redial list. (This doesn't affect the CID or redial lists on any other stations.) Add Call Block (CID list only) Add the number to the call block list (see page 36). Using Call Waiting A Call Waiting call refers to a call received on a line while that line is already in use.
29 press INTERCOM/HOLD again or press TALK/FLASH followed by END on the handset. Using the Headset You can use a standard 2.5 mm telephone headset with your cordless handsets. To purchase additional headsets (HS910), visit our website; www.uniden.com.
30 Using the Phonebook Each station can store up to 100 entries in its phonebook, and each entry can have two different phone numbers. Open the phonebook Press PHONEBOOK/LEFT. Scroll through the entries Press DOWN to scroll through the phonebook from A to Z or UP to scroll from Z to A.
31 Edit Number1 Enter the primary number (up to 32 digits) for this entry exactly the way you would dial it. If you need the phone to wait before sending the next set of - digits, press REDIAL/PAUSE to enter a two-second pause. If two seconds isn't long enough, you can enter as many - pauses as you want.
32 Phonebook Menu Options Open the phonebook with the phone in standby, and press OPTIONS to open the phonebook menu. From the main phonebook screen, you have three options: Create New Add an entry to your phonebook. (See "Creating a new entry" on page 30.
33 Using Multi-station Features The expandable base works together with the accessory handsets to give you some useful multi-station features. (A station can be any cordless handset or the base.) You must have at least one accessory handset to use the features in this section.
34 To leave a conference call, hang up normally; all other stations remains connected to the call. If you conference line 1 and line 2 together (see page 23), the base and four cordless handsets can hold a seven-way call with both outside callers at the same time.
35 Using the Intercom Here are some things you need to know about using the intercom: Whenever the phone is in standby, you can make an intercom call between stations without using the phone line. You can make an intercom call from any station, but only two stations can be in an intercom call at any time.
36 Using Special Features Using Do Not Disturb The Do Not Disturb or DND feature turns off the ringers of the base and all handsets at the same time. With the phone in standby, press and hold DO NOT DISTURB on the base. The phone automatically turns on the answering system and shows Do Not Disturb in the display on all stations.
37 Call Blocking menu options With the phone in standby, open the menu and select Call Blocking . Choose one of these options: View Number See the numbers on your call block list. Create New Add an entry to your call block list. The phone will prompt you to enter a name (optional) and phone number.
38 Using the Alarm Feature You can set 3 different alarms on each cordless handset so your phone can remind you of important events. When an alarm is set, the alarm icon ( ) appears on the top of the screen. Setting an alarm Open the menu and select 1.
39 When an alarm rings When the day and time on the phone matches the day and time of an alarm setting, the handset sounds the selected tone and displays the alarm screen. The alarm will ring for three minutes. To turn off the alarm, press END . When the phone prompts you to confirm, press YES .
40 Using the Answering System Each line has a separate answering system. Whenever you access the answering system, the phone prompts you to choose a line.
41 Delete your greeting Open the menu and select 1. Ans. Setup . Select 2. Line 1 or Line 2 , then select Greeting Options . While the system plays back the current greeting, press 3. DELETE to erase the personal greeting for this line. (You can't erase the pre-recorded greeting.
42 Getting Your Messages Accessing your system from a handset (remote operation) You can access your system from a handset whenever the phone is in standby. Only one handset at a time can access the system through remote operation, and you can't use remote operation if the base is using the answering system.
43 To... From the base From a handse t (during remote operation) replay previous messages Press PHONEBOOK/LEFT repeatedly until you hear the message you want to replay. Press 1 repeatedly until you hear the message you want to replay. skip a message Press CALLER ID/RIGHT .
44 Using the System While You're Away from Home You can also operate your answering system from any touch-tone phone. Before you can use this feature, you have to program a security code. Programming a security code With the phone in standby, open the menu and select 1.
45 Solving Problems If you have any trouble with your phone, try these simple steps first. If you still have a question, call our Customer Care Line listed on the front cover. If… Try… No stations can make or receive calls. Checking the telephone cord connection.
46 If… Try… No stations will display any Caller ID information. Letting calls ring at least twice before answering. - Seeing if the call was placed through a switchboard. - Checking with your telephone service provider to - make sure your Caller ID service is active.
47 If… Try… Messages are incomplete. The incoming messages may be too long. Remind - callers to leave a brief message. Deleting messages (the memory may be full). - The system keeps recording if I answer on an extension. You may have to change the line mode.
48 radio-based wireless devices, such as room monitors, wireless contr ollers, o r wirele ss headphones or speakers large fluorescent light fixtures (especially if they give of f a buz zing no.
49 Resetting and Registering Handsets If you are having trouble with a cordless handset or if you want to replace one, you need to clear the registration information from the base and the handset: Do you have the base the handset is registered to? Yes No Press and hold 1.
50 Registering Repeaters If you are having trouble with a repeater or if you want to replace one, you need to register the repeater to the base. TIP: Connect the repeater close to the base for easy access to the necessary buttons and indicators. Locate the repeater in the desired position after registration is complete.
51 Handling Liquid Damage Moisture and liquid can damage your cordless phone. If the handset or base is exposed to moisture or liquid, but only the exterior plastic housing is affected, wipe off the liquid, and use as normal. If moisture or liquid has entered the plastic housing (i.
52 Important Information Terms Used In This Manual Accessory Handset An extra handset that can register to and be used with an expandable phone base. All accessory handsets must be registered to a base. Base The main part of the phone. It connects to your phone line and lets you make and receive calls.
53 Battery Information Fully charged, the battery should provide about 8 hours of talk time and about 7 days of standby time. For best results, return the handset to the cradle after each call to keep it fully charged. Keep an eye on the battery status icon.
54 Index A Alarm Feature ....................................... 38 Answering a Call ................................... 24 Answering System ................................ 40 Any Key Answer ................................... 22 AutoTalk ...........
55 One-year Limited Warranty UNIDEN XDECT R055 IMPORTANT Evidence of the original purchase is required for warranty service. Warrantor: Uniden Australia Pty Limited ABN 58 001 865 498 Uniden New Zeala.
© 2009 Uniden Australia Pty Ltd/Uniden New Zealand Limited Printed in Vietnam UNZZ01096BB(0).
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Uniden XDECT R055 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Uniden XDECT R055 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Uniden XDECT R055, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Uniden XDECT R055 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Uniden XDECT R055, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Uniden XDECT R055.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Uniden XDECT R055. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Uniden XDECT R055 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
