Manuel d'utilisation / d'entretien du produit 640 Series du fabricant Ultra Start
Aller à la page of 16
www .ultrastar ter s.com FCC/ID Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2.This device must accept any interference received, including interference that may cause undesired operation.
OWNER ’S MANUAL PAGE 2 T able Of Contents T able Of Content s Page 2 Alarm Functions Pages 3-5 Arm System Disarm System Priority Unlock* Silent Arm/Disarm Panic T runk Release* Pages 7-10 Icon Descr.
P AGE 3 OWNER ’S MANUAL Disarm System 1.Press and release the button on the remote transmitter . 2.The park lights will flash and the siren will chirp two times.
Panic Mode Activating Panic Mode Press and hold the button for three seconds. The park lights will begin to flash and the siren will activate. Disabling Panic Mode Press and release the or button to disable Panic. NOTE: Panic mode will stay activated for sixty seconds.
Alar m Functions St arter Disable (optional) The system will interrupt the vehicles starter when the system is armed and allow the vehicle to start when the system is disarmed. Ignition Auto Locks (optional) 1) The system will lock the doors 2 seconds after the ignition key is turned to the “on” position.
OWNER ’S MANUAL PAGE 6 T emporar y Shoc k Sensor Bypass. Within three seconds press and release the button and then press and release the button. The system will chirp once when the button is pressed and once when the button is pressed. The shock sensor will be disabled until the system is disarmed and the rearmed again.
P AGE 7 OWNER ’S MANUAL SIREN ICON - This icon indicates that the alarm has been triggered. The remote will start to beep and the siren icon will come on solid at the same time as the icon for the violated zone.
OWNER ’S MANUAL PAGE 8 Setting The Time T o enter: Press and hold the and buttons until the remote transmitter chime and the minute portion of the clock begins to flash. T o change from minutes to hours, press and release the button. T o increase the minutes or hours, press and release the button.
P AGE 9 OWNER ’S MANUAL SERVICE MODE ICON- This icon indicates the status of the Service Mode feature. If this icon is present, the system is in Service Mode. NOTE: In Service Mode, keyless entry and optional features will still operate. ? SHOCK SENSOR ICON* - This icon indicates the status of the shock sensor .
OWNER ’S MANUAL PAGE 10 LCD Display (660 & 670) LOCK ICON- This icon indicates the LOCKED status of the system. NOTE: The doors will be locked (optional) and the LEDs on the antenna will be flashing. UNLOCK ICON - This icon indicates the UNLOCKED status of the system.
P AGE 1 1 OWNER ’S MANUAL T r ansmitter Prog ramming STEP 1 - Within 3 seconds turn the ignition key to the “ ON ” position three times leaving “ ON ” the third time. NOTE: STEP 3a (Default) - While holding the Program Button, press and release the button on each of the remote transmitters to be programmed.
OWNER ’S MANUAL PAGE 12 NOTE: Pause for 2-3 seconds between transmitters All the transmitters to be used must be programmed at the same time. All transmitters not programmed at this time will be erased from memory for security . The system holds a maximum of 3 transmitter codes.
P AGE 13 OWNER ’S MANUAL T o activate Car Jack Mode: T ype 1 (Door)- With the ignition key in the “On” position, open and close the door . The LEDs will begin to flash rapidly for 30 seconds. After an additional 30 seconds the siren will begin to chirp on/off for 10 seconds, followed by full siren.
OWNER ’S MANUAL PAGE 14 Emergency Ser vice Mode - (V alet Mo de ) T o Activate Service Mode: T urn the ignition key to the “On” position then press and hold the Program Button located on the antenna for 5 seconds. The system will chirp the siren 5 times as confirmation.
P AGE 15 OWNER ’S MANUAL Diagnostics While the system is disarmed and the ignition is in the off position, the LEDs will activate from the following triggers: 1) If the door is opened the LEDs will stay on until the door is closed. 2) If the hood is opened the LEDs will stay on until the hood is closed.
OWNER ’S MANUAL PAGE 16 Limited Lifetime W ar ranty The manufacturer warrants to the original purchaser of their remote starters and alarms, that the product shall be free from defects in material and workmanship.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Ultra Start 640 Series c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Ultra Start 640 Series - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Ultra Start 640 Series, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Ultra Start 640 Series va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Ultra Start 640 Series, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Ultra Start 640 Series.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Ultra Start 640 Series. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Ultra Start 640 Series ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
