Manuel d'utilisation / d'entretien du produit S1668 du fabricant TYAN
Aller à la page of 39
TY AN S1668 Dual Pentium Pro A TX 440FX PCI-ISA System Board User's Manual Revision 1.2.
2 S1668-A TX-001 http://www .tyan.com T able Of Contents 1. Introduction....................................................................... 3 1.1 Overview ................................................................3 1.2 Hardware Specifications.
3 S1668-A TX-001 http://www .tyan.com 1. Introduction 1.1 Overview The S1668 is a quality , high performance dual processor mainboard based on the powerful Intel Pentium Pro microprocessors. This mainboard is designed around the latest and fastest Intel 440FX chipset and can support CPU speeds of 150MHz through 200MHz.
4 S1668-A TX-001 http://www .tyan.com 1.2 Hardware Specifications/Features CPU Intel Pentium Pro 150 thru 200 MHz (Socket 8) (Single or Dual CPU configuration) Coprocessor On-chip floating point unit Speed 60/66 MHz system bus 30/33 MHz PCI bus 7.
5 S1668-A TX-001 http://www .tyan.com 1.3 Software Specifications BIOS A ward or AMI BIOS A T CMOS setup, BIOS/CHIPSET setup, and hard disk utility included. Support for easy BIOS upgrades with flash EEPROM chip. O.S. Operates with MS-DOS, W indows 3.
6 S1668-A TX-001 http://www .tyan.com 2. Board Installation 2.1 Unpacking The mainboard package should contain the following: S1668 Mainboard One IDE 40 pin cable One 34 pin floppy cable .
7 S1668-A TX-001 http://www .tyan.com VRM 0 PWR CON. 5V Com1 Com2 Bank 0 Bank 0 Bank 1 Bank 1 Bank 2 Bank 2 Bank 3 Bank 3 Socket 8 Socket 8 CPU 0 CPU 1 RT C Parallel Port PCI Slot 1 PCI Slot 2 PCI Slot 3 PCI Slot 4 PCI Slot 5 ISA Slot 1 ISA Slot 2 ISA Slot 3 Primary IDE Secondary IDE Floppy Con.
8 S1668-A TX-001 http://www .tyan.com 3.2 Jumper Settings: CPU Speed: J27, J21, J22, J23, and J24 CPU Speed J2 7 J2 1 J2 2 J2 3 J2 4 J 1 1 J1 2 150MHz 3-4 of f o n o n o n o n o ff 166MHz 1-2 of f o n.
9 S1668-A TX-001 http://www .tyan.com I/O Selection: J28 & J29 J28 J29 For COM 1 and 2 1 -2 1- 2 Default For InfraRed 2 -3 2- 3 Speaker Connector: J43 Pinout Assignments 1 Speaker out 2 Ground 3 Ground 4+ 5 V Keylock Connector: J44 Pinout Assignments Pins 1 to 3 for power LED.
10 S1668-A TX-001 http://www .tyan.com Reset Connector: J45 Pinout Assignment 1 Power Good 2 Ground T urbo LED Connector: J42 Pinout Assignment 1 Cathode 2 Anode Flash EEPROM: J32(Default 5V) This jumper should be left at the factory default.
11 S1668-A TX-001 http://www .tyan.com Soft Power On Switch: J1 Pinout Assignment 1 Soft Power On 2 Ground CPU F AN Power: J49 and J50 Pinout Assignment 1 12V olts 2 Ground 3.3 CMOS R TC CMOS R TC includes an internal battery and Real T ime Clock circuit.
12 S1668-A TX-001 http://www .tyan.com 3.7 Hardware Reset Switch Connector Installation The RESET switch on your cases' display panel provides users with the HARDW ARE RESET function which is the same as power on/off. The system will do a cold start after the RESET switch is pushed by the user .
13 S1668-A TX-001 http://www .tyan.com 3.10 DRAM Installation The S1668 uses a 64-bit data path from memory to CPU and can accommodate up to 1024 MB of RAM. The mainboard supports standard, EDO (Extended Data Out) and ECC(Error Correcting Code) 72 pin SIMMS .
14 S1668-A TX-001 http://www .tyan.com Memory T able Bank0 Bank1 Bank2 Bank3 Total 4MBx2 none none none 8MB 8MBx2 none none none 16MB 4MBx2 4MBx2 none none 16MB 8MBx2 8MBx2 none none 32MB 4MBx2 4MBx2 .
15 S1668-A TX-001 http://www .tyan.com 1. Make sure the ZIF socket lever is up. T o raise the lever , pull it out to the side a little and raise it as far as it will go. The top plate will slide back. 2. Align the CPU and socket Pin 1 corners. The pins on the bottom of the CPU should align with the rows of holes in the socket.
16 S1668-A TX-001 http://www .tyan.com 3.12 VRM Installation The VRM is required for the Pentium Pro to work. The CPU will program the VRM for the correct voltage needed. No jumper settings are needed, just install the VRM into the VRM socket nearest the CPU that is being installed.
17 S1668-A TX-001 http://www .tyan.com 4. BIOS Configuration A ward's BIOS has a built in setup program that allows the user to modify the basic system configuration. This type of information is stored in the battery-backed CMOS SRAM. Entering incorrect information or for- getting your password can lock you out of your system.
18 S1668-A TX-001 http://www .tyan.com 4.2. Control Keys PgUp key Increases the numeric value or make changes PgDn key Decreases the numeric value or make changes F1 key General help, only for Status .
19 S1668-A TX-001 http://www .tyan.com 4.3. Getting Help 4.3.1. Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen.
20 S1668-A TX-001 http://www .tyan.com Standard CMOS setup This setup page includes all the items in a standard compatible BIOS. BIOS features setup This setup page includes all of the enhanced features of A ward's BIOS. Chipset features setup This setup page includes all the items of the 430HX chipset features.
21 S1668-A TX-001 http://www .tyan.com Date The date format is <month>, <day>, <year>. Press <F3> to show the calendar . Base Memory: 640 K Extended Memory: 7168 K Expanded.
22 S1668-A TX-001 http://www .tyan.com Primary/Secondary Drive type This category identifies the types of hard disk drives that have been in- stalled in the computer . There are 46 predefined types and a user definable type. Press PgUp or PgDn to select a numbered hard disk type or type a number and press <Enter>.
23 S1668-A TX-001 http://www .tyan.com V ideo This category detects the type of graphics adapter used for the primary display system. It must match your video display card and monitor . Al- though secondary monitors are supported, you do not have to select that type in setup.
24 S1668-A TX-001 http://www .tyan.com Expanded Memory Expanded Memory (EMS) defines a 64 K page frame in the area between 640K and 1Mb containing four 16K pages that are windows into the EMS memory . Programs issue requests to the EMS manager to switch the page to any part of EMS memory .
25 S1668-A TX-001 http://www .tyan.com V irus warning This category flashes on screen. During and after the system boot up, any attempt to write to the boot sector or the partition table of the hard disk drive will halt the system and the following error message will appear .
26 S1668-A TX-001 http://www .tyan.com Boot Up Floppy Seek During POST , the BIOS will determine if the floppy disk drive installed is 40 or 80 tracks. 360K type is 40 tracks while 720K, 1.2M and 1.44M are all 80 tracks. Default value is Enabled Enabled BIOS searches for floppy disk drive to determined if it is 40 or 80 tracks.
27 S1668-A TX-001 http://www .tyan.com ROM ISA BIOS CHIPSET SETUP UTILITY A W ARD SOFTW ARE, INC. Auto Configuration :Enable DRAM Speed Selection :70ns DRAM RAS# Precharge Time : 4 MA Additional W ait.
28 S1668-A TX-001 http://www .tyan.com 4.7.1 Power Management Setup ROM ISA BIOS POWER MANAGEMENT SETUP A W ARD SOFTW ARE, INC Power Management :Disabled IRQ3 (Com2) :Off PM Control By APM :No IRQ4 (C.
29 S1668-A TX-001 http://www .tyan.com Doze Mode Defines the continous idle time before the system enters Doze mode. Standby Mode Defines the continous idle time before the system enters Standby mode. Power Down Activities Defines the the activities that can cause the PM timers to reload.
30 S1668-A TX-001 http://www .tyan.com PCI Slot 1/Slot 2/Slot 3/Slot 4/Slot 5 INT# For Default Setting. Connect to PCI System INT# PCI Slot1 INT A INT A PCI Slot1 INTB INTB PCI Slot1 INTC I.
31 S1668-A TX-001 http://www .tyan.com Resources Controlled By The A ward Plug and Play BIOS can automatically configure all the boot and Plug and Play compatible devices. If you seelect Auto, all the interrupt request and DMA assignment fields disappear , as the BIOS automatically assigns them.
32 S1668-A TX-001 http://www .tyan.com 4.9 Integrated Peripherals Integrated Peripherals A ward Software, Inc. IDE HDD Block Mode :Enabled IDE Primary Master PIO :Auto IDE Primary Slave PIO :Auto IDE .
33 S1668-A TX-001 http://www .tyan.com ST ANDARD CMOS SETUP P ASSWORD SETTING BIOS FEA TURES SETUP IDE HDD AUTO DETECTION CHIPSET FEA TURES SETUP DA VE & EXIT SETUP PCI SLOT configuration EXIT WITH OUT SA VING LOAD SETUP DEF AUL TS 4.10. LOAD SETUP DEF AUL TS ROM ISA BIOS CMOS SETUP UTILITY A W ARD SOFTW ARE INC.
34 S1668-A TX-001 http://www .tyan.com ROM ISA BIOS CMOS SETUP UTILITY A W ARD SOFTW ARE, INC. ST ANDARD CMOS SETUP P ASSWORD SETTING BIOS FEA TURES SETUP IDE HDD AUTO DETECTION CHIPSET FEA TURES SETU.
35 S1668-A TX-001 http://www .tyan.com 4.1 1. IDE HDD AUTO DETECTION ROM ISA BIOS CMOS SETUP UTILITY A W ARD SOFTW ARE, INC. CYLS. HEAD PRECOMP LANZONE SECTORS Drive C: (202 Mb) 9 8 9 1 2 65535 989 35 Do you want to accept this as drive C (Y/N)? Esc:Skip T ype "Y" to accept the H.
36 S1668-A TX-001 http://www .tyan.com 5.0 Flash Writer Utility Y ou can upgrade the BIOS of your mainboard by using a "Flash Memory W riter"(FMW) utility . This utility can be downloaded from the factory's BBS(Consult your system vendor for the phone #).
37 S1668-A TX-001 http://www .tyan.com T o reprogram the System BIOS, you must first do the following: 1. Check jumper J32 The S1668 uses a 5V Flash EPROM so jumper J32 should be left in the default postion on pins 1 and 2. This jumper should never be moved.
38 S1668-A TX-001 http://www .tyan.com Once you have satisfied the two requirements mentioned above, you can run FMW . Y ou can copy the contents of the “Flash” directory to your hard drive, or you can run the utility from a backup of the support floppy disk.
39 S1668-A TX-001 http://www .tyan.com 6.0 System Resources 6.1. TIMER & DMA CHANNEL MAP TIMER MAP: TIMER Channel-0 system timer interrupt TIMER Channel-1 DRAM REFRESH request TIMER Channel-2 SPEA.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté TYAN TYAN S1668 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du TYAN TYAN S1668 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation TYAN TYAN S1668, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le TYAN TYAN S1668 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le TYAN TYAN S1668, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du TYAN TYAN S1668.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le TYAN TYAN S1668. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei TYAN TYAN S1668 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
